-
Type of TRV to ask plumber to fit for Tado comparability
I am shortly getting my electrician to install a tado wireless control to replace the programmer & wired thermostat (I have a standard UK/Ireland Baxi boiler with one heating zone and one hot water zone). I would then like to replace my radiator valves with the Tado smart valves. However, a few rads don't have TRVs and…
-
Internet Bridge, Ethernet and Blinking Router Light
Every few days my Tado setup goes offline, leaving me without hot water or core functionality of Tado. My Tado is connected to my router via Ethernet with an IP reserved. It's powered via USB cable plugged into the router. Troubleshooting steps (with router powered on): Reserved IP address Verified all other network…
-
Opentherm Installation - Ideal Logic C30 Combi Boiler
Hi all, I'm brand new here! I'm moving into my new house at the minute, and in a burst of foresight I bought the Wireless Extension Starter Kit on Prime Day last year. The new house has an Ideal Logic C30 Combi gas boiler, and already has the Opentherm Harness installed. There is already a 'smart' controller installed in…
-
Hot water and heating not working independently
My system replaced a Honeywell ST6300a controller that allowed independent timing control of the heating and hot water. I followed the wiring instructions for the Tado controller and have checked, double checked and triple checked it’s wired correctly. However I can bring the hot water on independently of the heating, but…
-
Can I create 2 different houses i the same app?
Can I create 2 different houses i the same app?
-
Thermostat stopped responding to app
Hi all. My thermostat has stopped responding to the app. I’ve also tried to increase the temp manually in the thermostat but my boiler still is having none of it. I’ve got a plumber coming out tomorrow but I’m thinking since the thermostat seems to be playing up it might be that. The app does show the thermostat as being…
-
Bypass radiators too hot
Hi, I have 9 radiators over 2 zones. 3 bedrooms, 2 bathrooms and the hall on one zone. Lounge, kitchen and utility on the other zone. The hall and lounge radiators are the bypass radiators on each zone. The issue I have is that if I call for heat on the SRVs the lounge and hall are too hot. It’s uncomfortably hot to sit in…
-
Installing tado to two zones.
Hi there, I'm trying to understand how to install tado to my boiler. I have two zones - one for rooms and one for bathroom(with hot water), and I have two wired programmer for them individually. Based on initial consultation with Tado, I have to install wired thermostat and one extension kit. But, next consultation said…
-
Bosch Condens 5000W
Does anyone know how to hook up the tado wireless thermostat to this boiler type ? Service desk says its compatible. Appreciate your help in advance
-
Help with set up in a new build
Hi, New to tado and have a basic system atm that I want to expand. We live in a new build. There is a wired thermostat in our master bedroom with a fixed radiator valve (stays open) and this controls all of upstairs. There is another wired thermostat in the downstairs hallway, solely for downstairs. I have changed our…
-
Hot Water showing instead of Heating
I’ve just set up my V3+ kit for the first time, but it states Hot Water in the app instead of Heating. I can only control heating with the setup in my home anyway, so how can I reflect this in the app?
-
Any savings using eBUS when minimum boiler output is 7kw+
Has anyone gone from using eBUS back to using relay mode where their boiler is simply to powerful for the rooms they are trying to heat? The issue I have is my boiler is realistically too large for my central heating requirements (probably the same for most combi's fitted in the UK) My heating demand for the whole house is…
-
Combi boiler volt free, heating off boiler and ufh zone
Hi everyone, Just been to look at a job, customer has a tado starter pack. Combi boiler feeding radiators and a seperate zone for some ufh Combi (biasi s) only accepts volt free Customer had purchased an electric ufh stat which I advised isn't really suitable. Currently heating is controlled at the boiler. I've suggested…
-
Tado + Worcester Bosch 18ri + Modulation control
Hi All, It used to be so much better getting answers from Tado concerning things like this but I guess they've slimmed down their support with the amount of competition in the marketplace. I have the latest Smart stat and - Wireless Receiver [Programmer with Hot Water] along with a Worcester Bosch 18ri system boiler. I…
-
Combi Boiler OT Max Temp On Water?
hi all, i have a Vitodens 100-W WB1B combi with the Open Therm setup, all seems to work fine instructions from Tado were spot on. on setup though i was to believe it was heating only and the boiler would continue to govern the hot water which is fair enough, but since fitting, the hot water doesn't seem as hot and changing…
-
Wiring Configuration Tado Controller/Sonoff Temperature Control
I have read several posts regarding the desire to have temperature control for hot water through the Tado controller but believe this is currently not possible. As an alternative I am thinking of purchasing the SONOFF TH316 (the upgraded TH10/16 version) with temperature/humidity sensor to control my hot water. I currently…
-
Wireless receiver only starts boiler when zone valve has been manually opened
Hi I would appreciate words of wisdom. I've just installed Starter Kit V3+ with extension. (Replaced wired thermostat, Drayton programmer). Boiler is Worcester Greenstar 30CDi. Wifi all connected and hot water control is working via the app. However although the light showing response to heat demand is lit, boiler fails to…
-
Smart Wired Thermostat - Zone Controller
Hi All, So I have been through the help section and followed the instructions on setting up the smart wired thermostat and I just cant get it to become a zone controller. Some background, we have had the system for a good 2 years now and it all works perfectly, lots of TRV's, Controller for the HW (extension kit, also the…
-
Honeywell CM701 Bridge/loop wire
Can anyone help with why I have this wire from terminal A to C. I have another thermostat upstairs which is wired the same. thanks
-
Ability to open valves within summer
Does anyone know if Tado has got a way to open the valves without turning the heat on yet? Many boilers operate their pump once per day (mine doesn't) to keep the fluid circulated and exercising the pump. Without the ability to open the valves it means the pump isn't circulating the water around the full system which isn't…
-
Thermostats calling for maximum heat when in away mode
So… This is a weird one. No one is home, the system is in away mode, yet one of the rooms is asking for maximum heat even though it was automatically set to frost protection. I would have expected that that meant heat requests should be canceled IMMEDIATELY. I’ve manually turned off the whole house with the “Turn off”…
-
Upstairs rads not heating 2 zone
Hi, I've just installed Tado smart system to replace my old Danfoss system, I have a 2 zone system which I replaced the main TP9000 with a recieve kit, the TS sensor with a wireless thermostat, and a TP5000 with a wired thermostat, plus I have put smart TRVs on all rads apart from the 2 where the wall thermostats are. My…
-
Trying to connect my extender to my new Vaillant 425 Eco Fit Pure open vent boiler
It is an existing extender which controlled the water and heat, the old boiler was a Potterton. the extender went straight to the boiler so no programmer and wired/wireless thermostats also in the mix along with Rad valves. all worked fine until the boiler change. The system no longer works, I have tried to reconfigure in…
-
Tado & Mixergy?
Question- I've got a Tado thermostat with the wireless extension kit so that it can turn my hot water on and off. If I get a Mixergy hot water tank will Tado be able to handle that? Presumably Tado just controls the hours of operation (so you'd set that to be all day/night and let Mixergy manage the magic) and the presence…
-
Will changing to modulating control make old controller redundant?
Hi, long term Tado user here and now looking to change to modulating control. My current set-up sees a combi boiler connected to the original boiler control which in turn connects to the wired thermostat. Question is will the original boiler controls need to be removed if I want to get the full benefits of modulating…
-
Replace EPH Controller with Tado wireless
Hi all Tado support were no help. I managed to work out I need to replace the EPH controller. I assume this is with a wireless one. The wires behind the EPH are on N L, 3 and 4 but per the tado instructions it’s not clear where they map to there is no P3 for example. I can’t add pictures here to show. Can anyone help I…
-
Universa floor heating thermostat
I have replaced my floor heating thermostat from Universa and connected a Tado smart thermostat according to your instructions. I can't get it to work though, that the floor heating valve doesn’t respond. What could be wrong? Micke Granath
-
NEST
Believe me I’ve looked at previous questions but I think I’m getting lost. So here goes , I have a NEST Thermostat and only use that, now I’ve bought some taco valves , but as in reading I can see that I would be better with the tado thermostat to replace it, is this easy to do ,ie swap with same wires , and I keep reading…
-
How do I use Tado with a combi and two heating zones, UFH and rest of house rads?
Hi All. I've had Tado for over two years with a conventional boiler/tank/CH system. The existing system was a boiler with controller/extension kit, internet bridge, a wireless stat that I use in the living room to regulate the temp of two rads with Tado TRVs and then Tado TRVs on the rest of the rads throughout the house.…
-
Tado bridge and connectivity
I have bought a Tado wireless starter kit and 14 radiator thermostat, I haven’t been able to get them all to connect to the bridge, is there a extension to help with the signal ? If not can I get my money back it’s a big expense for something that’s doesn’t work as it should ?