-
Going from a 10 wire Drayton LP822 to Tado X
Hi, I currently have a Drayton LP822. The boiler has a hot water tank. I have looked at wiring guides online and everything seems straightforward, however, once i removed the Drayton LP822 I can see 10 wires (not including an additional 3 earth) and I can't make sense of how to wire this correctly. Any help would be…
-
How do I disable geofencing for hot water using Tado X?
I have a system boiler which means I have a hot water tank. The water needs to be heated periodically to ensure Legionnaires disease does not grow in the tank. When Tado X is in Away mode the hot water can only be set to on or off, there is no schedule. I am about to go away for a month in the middle of winter and in Away…
-
Hot water control like in V3 - other device control i.e. Apple Home, Google Home or Home Assistant
I have found it impossible to see any control of the hot water in any of the Matter/Thread control systems. It is impossible to add the wireless controller X to any of Apple Home, Google Home or Home Assistant. The only place that hot water can be controlled is through the app, and then only with the facility to set a…
-
All Tado X devices disconnected
Hi all, I upgraded from a Google Nest thermostat to a Tado X earlier in December and since the change I kind of had to battle with this system in a way or the other and I see in the forum I'm not the only (not sure if this is actually comforting). Anyway, after buying the second Bridge X I managed to have all the TRVs…
-
Rename Zone Controllers / Wireless Receivers
We should have the ability to rename the wireless receivers and give them proper zone names. I have 3 wireless receivers on my boiler for 3 floors in my house. When I add a new temp sensor or radiator TRV, I should be able to add it to 'downstairs' or 'basement' or 'upstairs'. Not to PR123456789! I installed all three…
-
Tado X Alternative as Tado X does not work with Home Assistant and no support
I have several devices (10+) and several of them deadlocked and the Matter Device Linking is not available… I've opened a ticket almost 6 months ago and the answer is "we are looking into it". Also to get the devices working was a nightmare I had to reset everything more than 5 times to the answer to "can you reset…
-
Tado X pairing connection Wireless Smart Thermostat X - Starter Kit
Hello there, I have the following problem. I just bought a Tado X Wireless Smart Thermostat X - Starter Kit The problems are the following: The Wireless Receiver X did connect with my wifi without any major problem (even if i needed 4-5 attempts). The Wireless Temperature Sensor X is not able to pair with my phone and…
-
Tado X Thermostat Always Shows Offline in Google Home
Got the Wireless Smart Thermostat X - Starter Kit incl. Programmer with Hot Water Control and OpenTherm, installed and set up flawlessly through the Tado app. In Google Home app I tap add vice, Matter-Enable device, it finds the thermostat, adds, creates the relevant credentials and I get the final message 'Device added…
-
Set the status of the radiator valve to off when reaching temperature.
Currently if i set the smart radiator valve X on 22°C, and reach the desirable temperature, the valve is closing but the status of the valve is not off but 22°C because that's the desired temperature. It will be nice to be off so I can turn off my distribution pump via smart plug, oparated with google home in combination…
-
Exposure of additional information to Matter for Tado X Radiator Thermostat
Hello, I'd like to ask if the development roadmap for the Tado X Radiator Thermostats has the exposure of additional entities to Matter planned in the near future? I'd like to see the battery % and also the valve position (valve open %) directly within the connected home automation ecosystem through Matter, which is…
-
Pre-heat and early start for Tado X
Hello, Just bought the tado x System and I am a bit disappointed that the pre-heat and early start feature are missing. Are there any plans to implement those two features? Please implement those two features🙏 Thanks, Florian
-
Vaillant VR33 + VR66 for 2 zones and HW possible?
Hello, I am writing for some advice on my proposed setup, to see whether it is feasible. I have a Vaillant Ecotec Plus 630 boiler (not combi) already connected to a VR66. I will be shortly connecting the VR33 module to enable OpenTherm. My objective is to run 2 zones + HW. One zone for rads upstairs and the second zone for…
-
Add missing features from V3+ to X app/system
On Tado support page https://support.tado.com/en/articles/3387209-how-do-i-set-up-my-tado-room-smart-schedule However this is for a V3+ system. If you have the newer X system, the following features are not implemented: - No schedule days - Edit time block - no geofencing option - Away - no preheat before arrival option -…
-
Add (back) hot water schedule to Tado X
I would like Tado to bring back a schedule for the hot water boost function. I have a combi boiler controlled by opentherm. It has a preheat comfort mode that keeps some water hot in the heat exchanger so that you get hot water more quickly . For economy I only really need this for the morning and evening rush so would…
-
New smart thermostat says I need a thread border, but I already have a Bridge X
Hello, I figured I'd try this here since the support chat person offered me one solution and then stopped responding. We have a tado Bridge X in our house and it has two smart radiator thermostats and a room thermostat connected to it and able to be controlled from the apps on my phone and my husband's phone. We recently…
-
Samsung Smartthings hub integration as border router
Hi all, I would like to ask to start the integration of Samsung Smartthings as border router. This integration should solve a lot of issue for the Smartthings users. Thanks Daniele
-
Tado X Wireless Receiver Sending Incorrect Information to OpenTherm Boiler
I'm trying to setup a Tado X system to use OpenTherm to control my Combi Boiler and it is not working. Setup: Vaillant ecoFIT sustain 835 combi-boiler, Tado Wireless Receiver, Tado Wireless Thermostat, Tado TRV's I first setup the system in relay mode and it worked fine. I then added a Valliant V33 OpenTherm module to the…
-
App logic under limit cases
Hi everyone. I just installed the TVRs in all of my house's 5 radiators, toghether with the Tado X Thermostat. I have a normal boiler (Ariston Clas HE), and I live in Italy. I'm new to smart thermostats and TRVs, but I find incredibly problematic the behaviour I just discovered: Using the app function "BOOST" which opens…
-
Single App or Bridge linking V3 and Tado X.
I propose a single App and / or a bridge product to links V3 and X products. This would enable those on V3 to extend their systems to reach distant radiators. Reason: Many people have invested in Tado products for their home on V3. These people identified the problem that Tado V3 had limited range and some radiators could…
-
Display Tado x on when change
The new tado x does not turn on the display when changing the temperature from the app, which the previous version V3+ did. It is not great that an updated version of the device has fewer features than the new one