-
App Failure
Hi, this morning the app failed to show any thermostat devices and seems to be useless. This is after a mail was sent confirming the offline schedule had been activated. Any clues, don’t want to delete the app and start again. Sherman
-
Merged: Multiple homes
This discussion has been merged.
-
Merged: Manage multiple homes through one Tado app
This discussion has been merged.
-
Merged: Multiple homes
This discussion has been merged.
-
Merged: how to add a second (and 3th) home with Tado to my app
This discussion has been merged.
-
Merged: Second home problem
This discussion has been merged.
-
Add Second Home (Multihome) - September 2022
Hi, when is the option being added to the app so we can control a second home. I find it surprising and to be honest, disgusting that this is not already a feature. I can see 3 years of complaints and an Admin person stating in April that it just keeps falling off the to do list.
-
Baxi cannot be turned off via the power off button
Hello, My boiler, Baxi Luna Duo-tec 1.24 E, is controlled via OpenTherm using the tado wired thermostat. Heating and DHW control works fine. I noticed that when I connected the thermostat via OpenTherm basically the boiler cannot be controlled via the HW buttons located on the front which is okay and expected, however also…
-
Tado with Viessmann 100-W
I have a mixed tado system (three zones with wired stats, trvs, strvs, and a wireless stat) that works well with my ancient Worcester Bosch boiler. The Megaflo hot water cylinder is heated via a timer switch on a fourth zone. I have no idea what controls the temperature of the DHW. I adjust the boiler temperature from time…
-
One tado out of battery, but the rest not stable anymore.
Curious to see if others have the same experience: I have one room with a tado knob being out of battery. I know, I should have replaced them; there was enough time, but I didn't. I had that before: when one room is out of batteries, the rest starts to be unstable. I have total outages, I have weird mis-readings of higher…
-
Central Heating not switching on via Tado (hot water ok)
Hi all, I'm looking for some help. I've installed tado wireless, thermostat, receiver and bridge. All connected. App speaking to thermostat and receiver and switching on/off hot water, boiler fires up. However with central heating the light goes on (receiver) when i increase temperature to switch on heating but it doesn't…
-
Humidity accuracy
How accurate do you think the humidity sensor is? My spare bedroom, with good airflow, no mould and at room temperature reached a humidity level of 71% whilst my bathroom, which I had showered in shortly before, only reached 67% even with the shower on. I feel like the sensors are pretty far off.
-
language for android
Hello, please add language settings for Android in the app
-
Internet dropping out
When my internet connection drops, which it does regularly, my boiler appears to be left firing at full force - so in house the temperature rises to apprx 25 degrees unchecked by any thermostat. If i am our of the house this csn mean hours of overheating whichbis dangerous for pets. When at home, until i can get the…
-
How to add tado when heating is controlled via manual time lock on boiler
Hi everyone , I’m looking for help - we control my current heating system ( Worcester green star) using the time clock on the boiler - we simply switch it on for a few hours on nights and use the manual trvs to only heat the rooms we wantt etc. w rush ally use our log burner as our main heat. We DO NOT have a room stat or…
-
Grant Vortex Kerosene Boiler Powers Rads, Ariston Nuos Plus Heat Pump Powers Potable
I moved into a pre-owned house in March. My previous house I equipped with Tago V3 TRVs, a control panel for the boiler and several wireless thermostats which I adored. I want that level of control back. So, I've been exploring the new home systems. It's a two energy source system. The first, potable heat pump water heater…
-
Homekit wouldn't recognise Tado
Hello, I have Tado for the last 8 years. It is a solid reliable system that works perfectly. I have added it before to apple home app (Homekit) before whilst trialling it with no issues. I have now sat up all my home in Homekit but It wouldn't recognise the internet bridge anymore! I made sure that my wireless network is…
-
Major concerns around the reliability of Smart Radiator Thermostat
I purchased a set of smart radiator thermostats last year with the aim of efficiently controlling room temperatures and reducing energy consumption in unused areas. Unfortunately, the devices have not performed as expected. Rather than saving energy, the thermostats frequently turn on by themselves, disconnect from the…
-
Temperature still visible with grouped TRV’s
In my Living Room I have multiple TRV’s, two of them for some reason intermittently lose connection. When this happens I cannot see the temperature on the main screen of the app. It just says the whole room has a fault. I think it would be better if you could still see the temperature of the room on this screen but there…
-
Model number shown in app
Can we please have the model number of the device show in the app, or at very least a serial number lookup on the support site. I have spent two hours so far trying to figure out if I can put NiMH batteries in my radiator valve. The "What type of batteries..." documentation says I can only put alkaline batteries in VA01…
-
Configuration
Hi. Just installed wireless receiver. When trying to test the system, only the heating clicks on. When I press the hot water test nothing happens, no clicks, no light on the receiver. I have triple checked the wiring and it is definitely correct and secure. After an hour of trying to sort it, I noticed in the installers…
-
wiring wired tado
hi, the 'customised' instructions were as clear as mud so here I am. an old setup so a bit more quirky: an old Danfoss timer + thermostat that is connected to the timer potterton promax he plus boiler the timer identifies ON, COM, L and N - but there is a bit of a maze of cables. can anyne suggest what the correct way to…
-
Whole House Override from main thermostat
HI, I'm new here, I did a quick search but couldn't find anything. We have an issue in our house which is that I love smart home tech but my fiancee hates it. We have a tado thermostat in the hallway with radiator ones in every room. Our house is quite drafty and cold and sometimes we just need to override the schedule…
-
Range of Internet Bridge / Multiple Bridges
I've recently bought a Tado Wired Smart Thermostat and 6 Smart Radiator Valves for use in my apartment, but came across an issue I wasn't expecting: I live in a 2 storey apartment with concrete construction and an unconventional plan, which means 3 of my Radiators are out of range of the Internet Bridge. I haven't been…
-
Help with wiring the hot water controler
Hello, I have just bought a Tado Starter Kit V3+ (in programmer with hot water control) Following and reading the set up instructions (but not yet physically fitting the Tado devices) they are very easy to follow, both for the Bridge and the Wall Thermostat, however the programmer isn’t as clear to me. Details and…
-
Further savings going back to relay?
I have been using Tado wired thermostat through to Vailant ecotec 831 for over five years, using ebus set up. Also have 4 smart tado radiator thermostats in my set up. Has worked without problems. However, the house is 1930s solid brick external walls with double glazing throughout and good loft insulation. Would I gain…
-
"feels like" temperature setting
21c feels quite different depending on the humidity in the room It would be great if the trv would adjust accordingly, depending on the humidity.
-
Boiler has runaway
About an hour ago I noticed it getting very warm and I tried to control it via the app and by the wall thermostat. Nothing worked and as the room temperature was approaching 27 deg c, I've isolated it. I've been trying to set up a smart radiatoradiator thermostat today and I wouldn't be surprised if that's something to do…
-
Mounting thermostatic valves
Thanks to the previous help. Couple more questions;- It defaults to room 2. I've tried to change it to something else, but the continue bar is still greyed out. I sea whole load of plastic bits in the box, but the ring on the base of the controller looks as if it will go directly onto my radiator. See photos. Am I right?
-
valve will not pair. Show tool + 03 code
I am new to Tado. I have collective heating and I am trying to install my valves. Installing the Internet Bridge was quick and easy. Pairing the valves is a nightmare. Following the instructions, I push the pairing button for 3s. The valve vibrate and shows the dash animation. After a while the wrench icon light up with…