-
Wireless temperature sensor and 12 smart radiator thermostats
Hi, I have looked around and can't seem to find an answer. If I have 12 radiators and only one wireless temperature sensor, I can only add 10 rooms. Is it the case that if I want a setup like this I need to have the wireless sensor always on and then all 12 should work, or is there a smarter way to set them up?
-
Underfloor and conventional heating - help please
Have underfloor downstairs where individual wired room stats, calling for heat, open the motorised valve to the manifold (turning on boiler), and the appropriate room valve. Upstairs there are radiators (with thermostatic valves) , and only one wireless stat controls the motorised valve feeding them. Hot water is…
-
Multi zone wireless thermostats
Can you replace two wired multi zone thermostats with two wireless tado thermostats and still control each heating separately? Or does the second thermostat need to be a wired tado thermostat? Thanks.
-
Make Smart AC Control expose more AC settings to HomeKit?
Is there any reason why the only options in HomeKit are cooling, heating and off? In the Tado app I can see that it knows the commands for auto mode, dry mode, fan mode, fan speed, tilt, fixed etc. HomeKit supports these modes and settings, I don't think it would be that difficult to expose these modes and settings to…
-
Zone Setup - Main wireless thermostat to override TRV heat calls
OK, so new boiler fitted and a wireless thermostat put in the lounge room, all other rooms have TRVs fitted. I've setup all the rooms in the app and added schedules, but I want it so that if the lounge is up to temperature then it shouldn't allow other rooms to call for heat. At the moment if a upstairs room calls for heat…
-
Please implement the possibility of disabled the three LED lights of the internet bridge
Hi Everyone, the Tado internet bridge has three very bright LED lights. I would like to have the possibility to disable those LED lights please. A configuration as described below could be useful for all users: by default, after booting, the LED's are also on but in the app and/or the web portal you can choose to disable…
-
Can I do it myself?
Hi all, just looking for some advice please. I've got a dual zone set up with wired Danfoss thermostats upstairs and downstairs. After speaking with Tado customer support, they advised that I can replace the downstairs thermostat with a wired Tado (as I want to keep the same location) and I can replace the upstairs wired…
-
Danfoss RA-N compatibility
I came across Tado via a Consumentenbond test (though it was for the older product) and now I am trying to install Tado X. It was unfortunate that I only discovered now that the radiator knobs only support so-called "thermostatic" knobs. I was wondering all along how do these knobs generate the torque required to turn my…
-
Bridge not connecting
Bridge has been functioning fine until a couple of days ago. Tried new cables different router, upright bridge, location changes etc net speed is ultrafast
-
Already use tado. New Air Source Heat Pump coming -
Hi. Trying to start a conversation... I have a question about a new heating system. I currently use Tado on my oil fired system. Starter Kit, TRVs etc. I will soon get an air source heat pump system. It uses Honeywell T3 programable thermostat as installed. I believe a T6 wall stat is an option. Simple(ish) question - Can…
-
New to me TADO. Water control problem
I have recently moved Into to a new to me house with TADO. The previous owner demonstrated the rads control and water on/off control on the wall thermostat. Now that I have set up on phone via the app I have no water On/off controls on wall therm control or on my app control. The app tells me that the internet bridge,…
-
Current status of open-source/API integration on V3+ and X models
Hi everyone, I am going to buy a tado system soon for my apartment and unfortunately I just discovered that only the V3+ model supports my boiler (a Vaillant VCW 180 with analog control). If I would buy a X I would have to rely only on Relay on/off. As I am interested (or have the possibility) to integrate the heating into…
-
Boost
Hi, is there a way to just boost the heating for let's say 30min V3+ wired ?
-
After 4 visits from an installer, Tado still doesn't work
I have been building a holiday cottage in Northern Finland. Construction has recently been completely, and we temporarily moved in here. We've had our underfloor heating system professionally installed, but a year later we have not been able to get the Tado thermostats to work. Even after inviting the installers back over…
-
How do I deal with having 2 COM(L) and 2 P1(N) wires to connect to my Tado Thermostat?
Dear Tado community Perhaps someone can help. The first thermostat I replaced had 3 wires (1 COM(L), 1 P1(N) and 1 NO wire). However, the 2nd thermostat has a total of 5 (2 com(L) and 2 p1(N) and 1 NO wires.) Could someone please help with the double COM(L) and P1(N) wires? I was not counting on that curve ball. Thanks in…
-
V3 Wired Thermostat Wiring and config help needed
Hi, I have a Potterton Promax 28 Combi Erp boiler with a Danfoss TP7001 wired thermostat. The TP7001 has two wires connected - Red to the 'H ON', Yellow to the 'H COM'. The blue wire from the cabling is there but disconnected. I'm unsure where these connect in the back of the Tado V3 wired thermostat. I don't know which…
-
Multi zone help
Hi members, I've had an issue with an install of my tado smart system, I tried searching but can't find the right response. I have two heating zones in my house, upstairs and downstairs on separate valves to the water tank. I had the smart thermostat installed and have the wireless one downstairs, but left the existing…
-
Honeywell t8400a -> tado
Hello, tado community! I’m seeking for help. I want to switch from Honeywell to tado, but I’m not sure if my current setup is compatible. I’ve recently moved to a new apartment, so everything has been installed by previous owners. Any help appreciated. Current setup: - District heating - Honeywell controller t8400a - 4…
-
What components do I need to make my Tado system fully smart?
I recent bought Tado Smart TRV starter + 4 smart TRVs. These work fine, in that I can schedule when they open the TRV and at what temperature. Mine is a single non-Zoned heating system, that still uses a manual Potterton EP3000 scheduler and an attached Honeywell "dial" thermostat to provide overall control of the boiler…
-
Travelling to a different time zone
The radiators in my shop are controlled by Tado via the App on my phone. I am going to travel to a different time zone this winter; so the clock on my phone will change to a different time. I have set up starting up and shutting down times as a program on my App for the heating. What time will this correspond to? The time…
-
Termostato Cablato non da il segnale di accensione e spegnimento alla caldaia.
Buongiorno a tutti. Premetto che ho già un sistema tado con termostato cablato e valvole in un appartamento secondario. Il problema ce l'ho nel mio appartamento Primario. Ho installato solo il Termostato Cablato e Internet Bridge. Tutto il sistema funziona. Se alzo la temperatura dal telefono si alza nel termostato e se…
-
Help needed with Worcester Bosch Greenstar 32CDi Compact
Hi, I've been using tado since March 2015 on a WB Greenstar R30 HE Plus (the tado replacing a TR2 wired thermostat). My old boiler died in early January 2022 and I've had it replaced with a Greenstar 32CDi Compact combi - no programmer or timer as I was expecting the tado to work. Unfortunately, I can't get the tado…
-
Home Assistant sync with Tado app delayed
I installed the Tado integration into my Home Assistant platform and it works quite well. One single problem: when I set my Tado thermovalves from HomeAssistant, the Tado app will update immediately, fine. But when I set the same Tado thermovalves from the Tado app, HomeAssistant will update after a few minutes, probably 5…
-
Make it easier to see which room is requesting heat by adding a symbol/colour to room Icon
I have a few rooms with smart TRVs and it always takes me a while to find which room is requesting heat. It would be easier if there is a little logo, or maybe a coloured border around the room icon if it is being heated.
-
User access to selected rooms only
Hi, Is it possible to give a user access to selected rooms only? Eg the kids only for their room and the living room? Or an au pair only for her room and the shared bathroom for example?
-
Automating Home/Away process
Apologies if this has been raised before but I couldn’t find a reference. When setting the system to “Away” provide an option to revert to “Home” either by setting a future date (preferred option) or at least by giving the number of days user will be away. This would save user forgetting or if out of internet connection…
-
Cooling function for Heat Pumps with floor cooling
Please create a function where we can use Tado with a heat pump (equipped with a cooling function) connected to a floor heating system to cool the rooms (with Tado thermostat) to the specified temperature. Each room is equipped with Wireless Smart Thermostat or Wireless Temperature Sensor. The heat pump is connected to the…
-
Panasonic 8/10 degrees mode missing
After a lot of reading about the AC controller, I was falsely mislead to believe that I’d be able to control ALL the features/buttons from my old Panasonic heat pump - but no - apparently Tado do not support such simple thing as modes. I have a vacation home where I need to be able to set an away mode, and when I’m there I…
-
Help bridging a wired thermostat
I have been using Tado with a wired thermostat and the wireless receiver for a while. Yesterday, I got myself TRVs and installed them, but when they call for heat, the boiler doesn’t fire up. I have been looking at other threads, and from what I can see, I need to bridge the wired thermostat so that the receiver takes…
-
The Tado internet bridge drastically slows down my internet connection
Hello, I've bought the Tado Smart Thermostat – Starter Kit V3+ and a Tado Smart Valve, however, if I have my internet bridge plugged in, my internet speed drops. I have a 900MB/s (DL) to 300MB/s (UP) fibre connection. If the bridge is unplugged, my speed and latency is stable at 3ms, but when I connect the bridge for just…