-
Fitting Tado remote to Ideal Boiler Vogue 32 Gen 2
Hi I have Tado valves fitted to radiators heated by the above boiler but working independently. I would like step by step guide to fitting the Tado remote thermostat to replace the ideal remote thermostat. Any help appreciated Thanks Graham
-
Danfoss adapters
I am new to this and apologies if I have missed the answer elsewhere on the forum. Can someone please advise how to fit the smart rad head to the pictured valve below. Thank you.
-
Adapter for EPH 75 TRV
Hi. New to Tado, but have successfully set up SRVs on four of six radiators. All six radiators have EPH TRVs but two of them don’t fit right- the SRT from Tado only screws on part of the way and then stops before the plastic tightens up so it remains loose. The valves are marked 15 & 94 on the ones that fit, but the other…
-
New wireless temoerature sensor and reciever
Hi any help greatly appreciated . I removed a nest wireless thermostat on a simple system boiler. When installing the tado I couldn't find my boiler and pressed a Honeywell controller . The thermostat now control the hot water output. How do I configure the reciever to simply control the boiler output to turn the boiler on…
-
Gravity fed system with no thermostat - Sanity check wiring plan
Hi All, I just wanted to post here and sanity check my proposed wiring before installing. We currently have a gravity fed system with no thermostat installed. Controlling both hot water and heating is done via a simple timeclock wired into the switched live on the boiler. When the timeclock is switched on both hot water is…
-
Tado wiring for switching a floor pump
Hi, I have one floorpump in our livingroom which I want to turn on and off when Tado wants to heat the livingroom. The current setup I’m using is an automatisation within Home Assistant that switches on/off a smart switch which turns on/off our floorpump. But what I don’t like is the dependency on Homeassistant. Is it…
-
Tado and Google Home
hi. is there any guidance for what I should I say for Google Home to instruct Tado? I have connectivity but verbal instructions always default to one room. All other instructions ( alternative rooms etc) respond with ‘ it looks that thermostat is not set up yet’! although occasionally it will work randomly when instructed.…
-
Does anyone know what versions of EBUS are currently supported by Tado in their wired or
Hi, I'm looking for a straight answer on what versions of EBUS are currently supported by Tado in their wired or wireless extension kit? I did see a post from 2019 saying EBUS was supported up to version V65 is that still the same or are more recent versions now supported?…
-
Heat pump connector availability in the UK
Is there any plan to release the heat pump connector into the UK market?
-
Is it possible to increase the minimum opening size on the radiator valves?
Hi Sometimes my radiators are wheezing (not just with the Tado smart valves, but the old manual ones too), I think when most of them are closed and a few ones are barely open. Now this is not an issue with the manual valves, I just set them to an opening when they are not wheezing. Because Tado adjusts them automatically…
-
Vokera vibe wiring
Hi I was fitting a tado to my brothers with the above combi, and when setting the tado up it couldn’t find the boiler model, do we email support for wiring instructions ? Thanks
-
what is the correct way to connect my Tado wireless receiver to my Vokera Compact 29A combi boiler
a wiring diagram for my question would be very.helpfull. Cheers
-
Replacing RWB2
I’ve got an old Glow-worm Mastermind RWB2 which uses the industry standard back plate. Boiler is a Worcester Danesmoor 20/25 oil boiler. Room stat is a Honeywell T6620B. I can only see one 2 port valve in the airing cupboard, and for the heating to come on, the hot water must be on too. I believe it’s gravity fed. Would…
-
Heating and hot water on
Hello. I replace my old termostat today with tado v3. I follow the wireing method but for some reason the heating and hot water is on even if is turned off. So I play with that for a good few hours. But still. I have to put it back my previous termostat. Any idea
-
Voice commands
Hi, According to the tado docs, we can voice command "one or multiple rooms". What is the command for multiple rooms? Currently I have setup manual routines/automations in Google Home, e.g. "Boost all heating", "Boost upstairs heating", but these are just 'change set point' ones which is the same as manual control. Also,…
-
Painting thermostat casing with water based emulsion.
Would be interested to find out if anyone has successfully painted thermostat to blend with wall colour? Thanks.
-
Is it just me, or is the graphing broken?
Both online, and via the Android app, the option to display a graph of temp/humidity under the 'heating' icon now seems messed up. it no longer shows the rough times across the top etc. It appears all that is compressed into RH side... this is from the web but my phone is just the same.. sigh. I suspect this is since last…
-
Receiver signal quality
Hi, Is there any debug option to know the quality of the receiving signal? I´m so sure that the developers have something to know how well it works. Actually the used radios should provide the RSSI parameter. So, is there any way for user to access to these metrics for helping during the installation? Thanks
-
Can Tado replace a wireless Danfoss Icon (water based underfloor heating) system?
Hi, I’d like to replace two Danfoss Icon Thermostats I have with Tado, I have a water based underfloor heating system from Danfoss, two zones, and two wireless Danfoss Icon Thermostats. The Danfoss module controlling the heating system is connected to the Icon sender module via Ethernet / RJ45 cable, which is what I’m…
-
How to connect two devices to one tado
Hi. I am dealing with a situation at my home. I need my Tado to turn on the boiler and the pump. There will be all three possible situations. That means boiler heating and pump not running. Boiler heating and pump running. Boiler and pump turned off. I have three wires running from the thermostat to technical room. Is…
-
Help replacing British Gas UT1 and hard wired temperature control
I’m trying to install my Tado starter kit to replace my old British Gas UT1 model. The house has a combi boiler, wired to the UT1, with a separate hard wired temperature control. Pictures of wiring attached and also the wired temperature control. Please could you advise on how to wire my tado in successfully as following…
-
Confirmation of kit requirements.
Evening all, I have been lurking for a while and have two questions for those who have Worcester 2/ 4/ 8000 models, or whoever has knowledge of these. 1, given the option between Tado with eu for modulation or the Worcester easy control. What would you have ? I can get both for a similar prices £150 - £170 2, if I went…
-
Opentherm with Worcester 25i ERP (GC47-406-60)
Hiya all. I am looking to fit a wireless V3+ starter kit to a Worcester 25i ERP. I want to use OpenTherm connections and Tado compatibility says its OK with EMS-Bus but not EMS+ Bus. The boiler says its EMS but doesn't stat which? Any ideas? Thanks :-)
-
Replacing Honeywell devices
Hi, thinking of getting a tado device as one of my Honeywell displays has failed. in one room I have a Honeywell wireless thermostat with bdr91 receiver this controls the heating in the house. there is a wired Honeywell thermostat in the kitchen which controls under floor heating. this is all connected to a green star…
-
Moving from a Danfoss wired RET-230L thermostat to wired TADO thermostat
I currently have a Draytom LP522 controller which has 4 Danfoss RET-230L wired thermostats controlling four underfloor heating zones and I would like to replace the thermostats with Tado wired thermostats keeping the Drayton controller. The RET-230L has a 3 wire connection (4 if you count ground) as shown below. How would…
-
DHW controls doesn't work Vaillant combi
Hey, I have installed the wireless receiver, a V3+ module and radiators thermostats, a v3+ was configured with Vaillant EBUS, before I have the vr 940f receiver by Vaillant and it can control a temperature of flow for CH and DHW. For now I cannot control CH flow in the tado app and cannot control it on the boiler but…
-
Anyone had success using Tado radiator thermostats as google home automation starter?
I’ve been trying to use Tado readings as triggers for Google home automations but the readings are not available. The are though in IFTTT. Anyone had luck setting this in in google home?
-
Tado smart trv
Why do the smart trv’s cost more from Tado professional shop than off Tado shop, I have bought the Wireless Smart Thermostat Starter Kit V3+ as it has Modulation Control but can see no difference in the trv apart from the guarantee. Thanks
-
Why can't Home Assistant see TADO thermostats?
TADO working fine if individual STRVs are added to dashboards but where 2 x STRVs are controlled in TADO by the room stat in that room I cannot get the thermostat onto the dashboard. This means the zone temperature cannot be simply adjusted like a single STRV can. Looking for a fix by TADO!
-
Wireless Smart Thermostat V3 - Vitodens boiler - OpenTherm query
Hi - I have an Visseman Vitdodens 100 OpenTherm compatible boiler. OpenTherm updated their technology in 2021 and I want to know it the Wireless Smart Thermostat V3 supports the full latest Open Therm technology which was updated in 2021? I presume I need to get the EU version? If so, is there anything additional required?…