-
Fault in Tado App heating schedule
The tado app changes our heating schedule without any input whatsoever from our side. Geofencing is off. We don’t subscribe to Auto-Assist so seemingly it’s the App that ‘s at fault. Any suggestions what we can do would be a great help.
-
Replacing ESI water programmer with Tado Receiver
Hi everyone, I've got an ESI programmer, ES2247B, which I'm replacing with a Tado Wireless Receiver. The problem is the wiring; I should have some wiring according to the instructions. In reality, it's different. Here is my current wiring The problem is that instructions tell me to put the NR 1 cable into HW NC and NR 3…
-
Replace MySon Touch RS with Tado Wired Thermostat
Hi All, i have a few myson touch RS thermostat thats hooked up an UFH system. is it possible to switch it out with the tado wired thermostats? i have tried to look up how to replace them but couldn't figure out how to do it.
-
Q re upgrade from v1 to latest version and radiator thermostats
Hi. I have the very first Tado, v1 which is not compatible with Apple or add ons. I have a very old non-combi boiler which I am in the process of upgrading to combi. Due to compatible issues and a failing battery on the v1, I’m tempted to upgrade to v3 and go with rad thermostats all around so I can can be precise on where…
-
Heating partial load/ range rating
Hi Folks, Hope you can advise. Keen to reduce usage/cut bills. How do I find the range rating on Vaillant Eco Tec pro 28? Looking to see if it's auto or should be lowered? (To what?) I'm in a top foor/2nd floor 3 bed flat all on one floor, built around 2000 and I've 10 radiators. Gas does rads and hot water and electric…
-
tado V3 not support Mitsubishi air conditioners
:'( Just replaced two Mitsubishi air conditioners for my new home, when I setting up for the new machine, tado can rec the rc signal but the apps keep saying we couldn't identify your AC model Signal detected Could not identify AC AC model : 1） Mitsubishi SRK53MWKH1 2）Mitsubishi SRK25MHIP1 Any one can help? No any reply…
-
Towel rail valve fitting.
I would like to put a thermostatic radiator valve in the bathroom towel rail. I tried an existing tado valve I have with the standard fitting. The metallic ring screws in, but the plastic bit is a bit loose. When I try to fit in the valve itself, it does not lock in as the pin sits too tall. I tried the various valve…
-
Energy IQ not generating consumption.
Hi I've installed 4 wired thermostats to the 4 underfloor heating zones and 1 wired thermostat to the upstairs where I have radiators. I've also installed 6x tado TRVs and all working fine. Only issue I have is the energy IQ does not load any consumption data even after 24hrs, I've put my tariff in and meter readings but…
-
TRV Showing Incorrect Temperature
I woke up a few days ago with the heat very high in the main room. The thermostat was reading 17 degrees even though the room was about 25. I tried resetting by removing the batteries but had the same issue. I contacted support and did not get a response but I suspect they did a remote reset because I had a strange error…
-
Radiator thermostat moving the valve pin in/out?
Hi I'm new in tado. I started to mount bridge, pairing main thermostat and for the start mounted two radiator thermostats. Everything looks fine, thermostats did a calibration, when i connected to my FAR thermostatic valves. OK, my boiler is off , main tado wired thermostat is not yet connected. But when i changing…
-
Will tado work for my house?
I don’t know anything about heating systems. But my goal is managing the temperature of each room separately, make it comfortable and save money. I have Eneco district heat with Honeywell chronotherm IV in my leaving room. My house has 2 floors and 7 radiators (normal ones not floor). 1st floor 3 radiators - 2 in the…
-
No Heat! How do I fix it?
Hi All, I had someone install my tado v3 kit a few days ago. I have since found I have hot water but no heating. The App says it's on, and the light on the wireless reciever is on, but the pump in not pumping and the boiler is not firing. I have attached a picture of the current wiring. Can anybody tell me if this has been…
-
Starter kits
Just to confirm this is still correct with wireless starter kits at this time. uk version with weather comp euro version with open therm Thanks
-
Temperature change
Hi, I have my Tado set to a schedule but i have noticed the temperature goes up from the set temperature in a couple of rooms and I need to press the schedule button to re set !
-
Hot water just turns itself off when using Alexa
I use Alexa voice control to turn the hot water on, but I'm finding sometimes it will stay on for an hour or longer, other times it will randomly turn itself back off after only 10 mins. I don't have any schedules or time blocks set and I've tried it on both home and away modes and still have the problem. Hoping someone…
-
Underfloor and radiators system
Hi, I am looking for some help on which Tado products I need for my heating system... I have a gravity fed Y plan system with 1 zone underfloor heating downstairs in our kitchen/diner and the rest of the house on radiators. I would like to control the underfloor separately to the rest of the house, how do I go about this?…
-
Best setup for central heating from building
Hi, I’m new to this topic and would appreciate help in selecting best setup. Many thanks in advance!! Setup - I live in a building with communal heating (central boiler runs 10-22hrs, I cannot control it) - heating reaches my apartment through a main valve at the entrance, which is controlled by a radio “dumb” thermostat -…
-
Heating not going off
I have just fit the tado V3+ starter kit to my glow worm ultimate 3 30c combi I have got everything paired up as per instructions but the heating will not turn off even though the heating indicter on the receiver is off. I have noticed the Htg symbol on my boiler display flashing which it does when a Htg demand is req.…
-
How to add wireless temp sensor to hot water control
I had a working system for a few years then my wireless temperature sensor seemed to die. So I replaced it with a new one. I can't figure out how to add it to the hot water control. It now only shows the main box where it also displayed my previous wireless temp sensor which I've now removed from my setup. Hot water had…
-
Two boilers, two protocols, two thermostats?
So... I'm looking into replacing my current Nest thermostat with Tado. Our situation is as follows: Old part of the house: 8 radiators, wired thermostat on boiler one (opentherm). New part of the house: Floor heating, no thermostat yet on boiler two (EMS). Now I was thinking of getting the following, but I'm not sure this…
-
Changed boiler now Tado won’t communicate
I recently changed my boiler and moved to a new position. Tado receiver has not moved. Trying to re wire the new boiler back in and tado receiver is not turning heating on or off. The receiver clicks and lights up when I use the app but the boiler does not respond Could someone one help confirm that I have the wiring…
-
Issues with Tado keeping valves closed this season?
Hello, I have been using tado sind september 2022. The overall use of the system in that season was satisfying. However, since I started the system last Sunday, I have noticed weird behaviour of the system. First indicator was looking at the „Energy IQ“ module of the app. There I could see the predicted costs have reached…
-
Replace Danfoss RX2C and Danfoss FP715Si
I have a Danfoss RX2C with a wireless room thermostat and a hot water thermostat. These are all linked to a Danfoss FP715Si controller. I recently purchased a Tado V3+ starter kit and in the instructions for the Wireless Receiver I can select either the FP715Si controller or the RX2C, but as far as I know these 2 do not…
-
What to do with zone controller 'dummy room'?
I have three zone valves in my house: 1) hot water tank; 2) downstairs heating; 3) upstairs heating. Following guidance from these forum pages, zones 1 and 2 wired so as to be activated by the extension kit, and zone 3 is activated only by a wired smart thermostat. So far this works ok; rooms (using a mixture of smart TRVs…
-
Is the V3+ voltage free or low voltage?
Is the V3 plus voltage free or low-voltage? I have a voltage free boiler which is constantly on and cannot get infinity answer
-
Tado thermostat
Hello, I’m using tado for about 2 months and noticed weird behavior. Is that normal when temp drop by 0.1 boiler is triggered? It doesn’t make sense for me as my bill is 13€ per day! I’m using single wired thermostat. I noticed is better to set lower temp but heat 2x or 3x for 1h or less every 2h or whatever to higher temp…
-
How to connect the wireless receiver to my system
Hi guys, I have a tado wired thermostat which is in my living room that controls the floor heating. I have radiator thermostats in the first floor and the attic. Recently I found out that tado only heats up the radiator when the thermostat in the living room requests for heating. I have city heating and I live in…
-
boiler not firing
hello - problem with my tado system wired extension kit boiler doesnt fire when the radiator smart thermostats call for heat boiler fires when hot water is turned on help!
-
Should my boiler Alway be heating
I have an atag is18 boiler, 10 radiator valves, Controller and a wireless thermostat. Only had it all for a week and slowly working it all out. But even if I select all rooms to off the protect/care tab says that my boiler is heating? Is this correct? Many thanks
-
Fitting Tado remote to Ideal Boiler Vogue 32 Gen 2
Hi I have Tado valves fitted to radiators heated by the above boiler but working independently. I would like step by step guide to fitting the Tado remote thermostat to replace the ideal remote thermostat. Any help appreciated Thanks Graham