-
Internet Bridge and Ubiquiti Unifi Dream Machine
Since a few days I keep having issues with the Tado internet bridge not connecting to the Cloud, the LED keeps blinking. The bridge is connected to my Ubiquiti Unifi Dream Machine and the configuration has not changed over the last years, it used to work seamlessly. Anyone having the same experience or issues?
-
Tado X migration from V3+ with Worcester Bosch EMS
I am looking at the Tado X and wondering if EMS or EMS+ is supported on Tado X as I can only seem to see reference to OpenTherm. I also have 1 room where I have two Radiators with Smart Stats and a central stat controlling the two rads. I am guessing this is still possible? Also if anyone has made this migration and…
-
TRVs micro adjusting a lot - how to stop?
Has anyone else experienced Tado TRVs micro adjusting and have a solution to stop it, because it's noisy and slightly annoying in my bedroom. For me it only happens during the heat-up phase. I bought them about three weeks ago, maybe they are calibrating or something, or maybe it's a permanent thing. I tried to have the…
-
How to read the tado graph
I've been monitoring the tado graphs for each room for quite some time now. They are great for seeing how the temperature fluctuates throughout the day, but there is no "key" to explain the shadings below the line. Take a look at the graph below ... There are 4 shades of grey - but what do they represent? My assumptions…
-
Firmware confusion
Can someone definitively tell me the latest firmware numbers please?? Smart TRVs , Smart thermostats, temp sensors etc ?? Also how regularly do Tado offer new releases ??
-
Tado TRV when boiler on frost protection
Might seem like a daft question but have installed Tado v3 thermostat and TRVs on all radiators in a holiday home, during the winter it’s empty and we always put the central heating (condensing) boiler on frost protection. With the trv in frost protection when the temperature drops below 5 degrees will that turn the boiler…
-
Tado X and Matter device compatibility (temperature sensor)
Hello, I'm wondering if the Tado X system that should be use Matter, can handle any Matter compatible temperature sensor. Thanks M.
-
Advice needed
Hey Tado community, I hope everyone is staying warm this winter. I wanted to reach out about a concern we're facing in our new build home and see if anyone else has experienced something similar. In some of our bedrooms, we're struggling to maintain a temperature beyond 20°C. Our developer, mentioned that NHBC considers it…
-
Heating Rooms
Hi i was thinking of putting my heating on all day at 16° just to see how much it actually costs out of curiosity more than anything else as i always hear keeping it on 24/7 is false economy but as i say curiosity got the better of me. So I set the tado up for all rooms with smart valves to 16° and just left it after a few…
-
My opinion: Tado needs to improve
Summary: Tado loses signal every day, multiple times per day and takes my heating/hot water with it. Tado's products need vastly better connectivity options. I truly cannot believe there is no "offline schedule" built in to Tado by default. That should have been a critical day one feature before the product was ever…
-
Compatibility
Hello, I have a boiler for water and heat that has a dual controller and then a thermostat to control the temps. I also have water solar but looking at the diagram this is not controlled by this as I have a separate solar controller. I want a tado V3+ and the values for the radiator. I'm hoping to keep my newborns room at…
-
Future proofing & old boilers
I am planning to install a Tado system. My boiler is old. A V3+ system would be perfectly adequate at the moment. However, if I replace the boiler with a heat pump in the next few years will I regret not fitting the X system? Why?
-
Configuration advice for legacy boiler
I have a gravity-fed Potterton Suprema 60 boiler configured in a Y-plan. I recently replaced the Honeywell (water and heating) timer after it broke with a Tado Wireless Receiver and Smart TRV valves in all the bedrooms, lounge and dining room. Some rooms, like the downstairs toilet and conservatory radiators, still have…
-
Why isn’t my heating working?
Hi, I have been having problems with my heating for that last 2 days. Initially, it started with overheating on the weekend, waking me up at 03:00am on the 19th with a room heating to 25 degrees that shouldn’t have been on. I turned this off and went to work yesterday (19th) but when I arrived home last night the heating…
-
Heating not working
Hi I’ve followed the app’s instructions to wire the receiver into the boiler and connect it to the WiFi and I’m all connected it says but the app or thermostat isn’t actually controlling my boiler it says it’s heating but the radiators don’t increase in temperature please help haha
-
Does tado measure relative humidity?
Or does it just measure humidity?
-
Anyones v3 Thermostat display an incorrect (lower) temperature thus cause continual overheating?
I have an issue that is similar to others regarding ‘overheating’ however I have an extra issue on top that – which is that the actual Thermostat (and App) is displaying the wrong current room temperature, which I believe is causing the overheating – I’ve not seen this mentioned in other “overheating” posts. Set-up: Wired…
-
Multiple tado stats
Hi there, I've been happily controlling my central heating with a tado starter set for about a year now. The only problem I have is that the stat is in the kitchen, if I'm doing a lot of cooking or if the Woodburner is lit in the kitchen, the temperature setpoint will be satisfied and therefore Tado will stop the boiler.…
-
Heat-only boiler with programmer and wired thermostat - confused as to the best setup!
Hi, I've tried to do some reading but am getting a little confused as to the best set up for me. Can anyone please help? I have a Baxi 600 heat-only boiler (+ hot water cylinder upstairs), which is connected to a Honeywell ST9400S programmer. There's a wired thermostat in the hallway, and I can control both the central…
-
How accurate are the humidity readings
Hi just wondering how accurate are the humidity readings on the trv’s ? Thanks
-
Merged: Device Linking
This discussion has been merged.
-
Can the Smart TVRS on each rad work as a stand alone unit in the event of a failure of the wireless
Can Smart TVRS on each rad work as a stand alone unit in the event of a failure of the wireless system
-
Tado v3 extension and a New boiler
Anyone has any experience regarding the Baxi Platinum iPlus 24AF? Specs talk about a R-BUS connection. Is it ok with tado?
-
Heating
my radiator are coming on with hot water something not right with wiring hope someone can give me some advice thank you
-
tado & multizone wet UFH
Hello, On our first floor, we currently have a single zone UFH set-up, using a Robot manifold. The manifold has a 'dumb' TRV on it. We have an internet bridge. The dumb TRV is paired to a wireless smart thermostat which senses the temperature in the zone. This wireless thermostat is also paired to a wired thermostat which…
-
Energy IQ, opentherm
Hi, I live in Scotland, I have a v2 system, my current boiler is a Viessmann Vitodens 050-w B0KA, which was installed in January 2024, replaced an Alpha Intec. The installer connected the v2 extension kit using relay mode, the heat flow was setup to 60 C and the hot water to 60 C. After the installation I haven't changed…
-
Help with setup for a Worcester Greenstar 38CDI Classic with pre-existing wireless thermostat
I'm a bit stuck and can't find the answer readily on these forums (perhaps down to my own searching and comprehension). Not particularly technical either so any advice would be appreciated. We've moved into a new house recently, and would love Tado system with TRVs on most radiators. What we have: Worcester Greenstar 38CDI…
-
Tado devices too slow to react
Hi everyone. I have noticed recently that my devices are very slow to react. I change the temperature on the phone and it takes around 5 minutes for the change to be reflected on the device. I also request the devices to blink and there is no effect until after 5 minutes that I see the blink. Is this normal? Any help on…
-
Do I need the wired or wireless starter kit for my setup?
Hello, I have below setup in my home, I'm confused to whether to buy wireless or wired starter kit, can someone please help? Y plan setup, I think central heating is pump fed (please see pictures) Potterton profile boiler Wired Thermostat in living room Honeywell ST699B controller As per title do I need wired or Wireless…
-
Connecting receiver to a Worcester 34CdI Classic
Spent all day on this. I've connected as per Tado instructions. The white light comes on when heat is required but the boiler doesn't fire. L to Ls, N to Ns. Grey to Lr. Black not used. Nothing happens with or without the jumper between Ls and Lr . I've tried with and without the built-in programmer attached. When…