-
Temperature sensor accuracy
Is the temperature sensor accurate, it consistently reads 2 degrees c colder than it actually is. Is there a way to calibrate it properly?
-
Geofencing not working
I also have the same issue with geofencing not working. I raised this issue with Tado and got the following response Thank you for your patience. The target temperature increased 1 hour before you were home, it was just not enough to trigger a heat demand before 7:23PM. This means you were moving faster than the App knows…
-
Thermostat not controlling the boiler
I have installed the wired thermostat but it doesn’t seem to control the boiler. I set a target temperature, but the boiler does not shut off once the target is reached - it carries on heating and pushes on to higher temperatures. This is true in the smart schedule and manual settings. Can anyone help or guide me with this?
-
V1 Installtion
Hi I have the original V1 beta which I have not used since probably 2019. I powered it up today and it said all components were offline. I then deleted the home so that I can add everything back again. But it's asking for the serial number and 4-11 digit code. I have the serial number but where do I find the code?
-
Upgrade tado app for more Homes, connection with external open window sensors
I have two Homes, and I installed new thermostats on tado° X radiators in my home. I have a V3 system in my company and I had to create a 2nd account. This causes complications especially with Geofencing!!! When will the new version of tado° for multihomes be available? It would be good if the tado° app could respond to…
-
Altantic Boiller and Tado wiring
Hi everyone, I'm in the process of replacing my old thermostat with a wired Tado V3, but I'm running into an issue. The old thermostat had just two wires connected to it, and following the manual instructions, I connected these to the + and - terminals on the Tado (on the right-hand side) and set the correct settings…
-
Tado to Worcester Bosch GreenStar 30i Digital Interface EMS Connection Bus (Working Setup Attached)
Hi below is a working setup for a Worcester Bosch GreenStar 30i Combi Boiler using the Digital Interface EMS Connection to a seperate wireless tado thermostat in another room I hope others find it useful Basically I removed my old Hive connection and receiver altogether from the boiler before i started on setting up Tado I…
-
House WIFI and Tado system
Hi. I am confused and cannot seem to find an answer to my question as to if the Tado system does or does not use your home wifi. I have a Tado Bridge connected to my BT router ethernet port, I have a thermostat, and a Wirless receiver near the tank in the loft. If my home WIFI generated by the BT Hub goes down I cannot…
-
Thermostat Receiver not communicating with boiler
Hi there, we had a danfoss receiver installed previously and we replaced it with Tado. We followed the same wiring based on how the danfoss was wired and for a couple of days it was working fine. After 2-3 days the Tado stopped communicating with the boiler and now when we boost the heating on the app or turn on the…
-
TRV Compatibility
Hi, I have the V3+Thermostat with an additonal stat. I want to add some TRVs. Would the Tado V2 TRVs work with what i have? Thanks
-
What happens when last valve closes at the end of heating cycle?
Hi! Setup: all radiators with tado thermostatic valve + thermostat to control the heating start/stop Scenario: heating is on, last thermostatic valve reaches set temp and closes → thermostat should switch the heating off Heater PoV: 'stop' signalled from thermostat so burner goes off, and the water pump kept on until the…
-
SOLVED: tado setup for one boiler with two heating circuits (UFH and radiators)
Slightly odd one perhaps but as I spent quite a bit of time researching whether tado could work for my home's heating setup and didn't find any clear answers I wanted to post for others to see that it is possible -- and how! Original setup: one boiler (Vaillant EcoTec Plus 838 + two heating circuits, one for the underfloor…
-
New setup with combi, rads and UFH - advice needed
Seeking advice. Have been a happy Tado user with a conventional heating system controlled by smart thermostat and trv’s for radiators and extension kit to add hot water control. Now moving to a combi boiler with radiators and UFH and ideally want to use Opentherm by connecting the extension kit to the boiler to control.…
-
Controlling two radiators in a room
Hi. I have just installed Tado X. I have a room with two radiators, each of which has a wireless smart thermostat X, but there in no wireless temperature sensor X in the room. I want one of the radiator thermostats to control the temperature of both radiators. In the old Tado system, I could set it so that one of the…
-
Buderus logamax plus gb072 (RC310)
Good day, I want to buy a Tado smart thermostat. I have a gas condensing boiler at home, brand Buderus logamax plus gb072-24k. I already bought one thermostat of another brand, which unfortunately could only On/Off, and I need it to communicate with the boiler also based on changes in the temperature of the circulating…
-
Has anyone found 'early start' worth persevering with?
Hi, Day 4 of our tado system up and running here. A few teething problems but so far OK. I've done some forum searching now and see the 'early start' function does not get a lot of love! So far the rooms I've had early start activated on (I've followed advice is earlier threads and not used it in smaller rooms - only in…
-
Changing internet provider
I am changing my internet provider do I have to do anything for Taxi to operate
-
Replacing a Tado wired Smart Thermostat with a Tado Wireless Smart Thermostat
Hi all I currently have a Tado V3+ smart thermostat hard wired to a Tado V3+ Bridge. The location of the thermostat and wiring is historic and due to a remodelling of the house this thermostat is simply in the wrong place. Because of its location the heating is constantly trying bring the heating up to temperature in the…
-
Replacing BOSS THERM wireless thermostat
Hi I have ordered a Tado Wireless Smart Thermostat Starter Kit V3+ with Hot Water Control and currently have a “BOSS THERM” thermostat and receiver (looks just like a Siemens) connected to a Glow Worm combo boiler. Will it be a easy swap?
-
wired thermostat - wiring
help wired thermostat Logic Heat 15 Boiler I’m replacing my Therma Wired Thermostat with a Tado wired thermostat, need help with the wiring and set up.
-
Energy consumption with Tado
Hi Everyone, I updated my old wired thermostat and programmer with Tado Smart V3+ wireless system (including smart radiator valves). I set individual temperatures in every rooms and I realized that my boiler is on much frequently but for shorter periods than before, according to the heat demand per rooms. Obviously trying…
-
Swapping BPT TH/124 with tado° X
Hello chat, I'm looking into swapping my current BPT TH/124 with a tado X, but I'm unsure about the compatibility as I'm not finding a wiring diagram matching my thermostat. From what I'm seeing, it should be compatible and pretty straight forward as current wiring is on C and NO (NA), which should be pretty much the same…
-
Last ditch attempt before I send my Tado wired thermostat back (UK)
Hi all, I am wondering if anyone has successfully got the following to work and if so, how? I am just at the point of giving up and returning the Tado Wired thermostats. So the background is: I recently moved into a new build and it has a combi boiler and a dual zone thermostat wired setup to a wiring centre. The boiler is…
-
Tado X No Matter Code For Wireless Reciever X Therefore No Hot Water Control
When running V3 I had linked the bridge to Homekit and had a hot water option in home kit. Just in the process of adding my new X equipment to homekit and expected to see a matter code on the wireless receiver X so that I can add the hot water control to homekit but no code present. How are you supposed to add hot water…
-
after mounting the thermostat the calibration doesn't start and show it's not mounted yet.
My thermostat V3 does not recognize when it is mounted. When putting it on the socket at the radiator it just does nothing. How can I make it recognize that it was just mounted on the radiator to start the calibration etc.?
-
Tado Manual Control settings
Recently one of my radiator valves has not been following settings - in the settings I have it set that when I manually change the temperature it should do it for a set time. This wasn't happening and it was just doing until I resume schedule. I contacted tado and they asked me to swap it with one that is working…
-
Why does 'wired' thermostat require batteries?
Considering replacing wired thermostat (+ controller) with Tado wired system. Why does Tado 'wired' thermostat require batteries. In the proposed installation, a remote village hall, battery thermostats are a no-no. If allowed on here, and if Tado DOES need batteries, can anyone recommend a system that doesn't, but still…
-
why does my Tado ignore my schedule
for some unexplained reason our TADO keeps ignoring the existing schedule and decides we only want/need 7 degrees. Any ideas?
-
Open Letter with ChatBot support team
My apologies for the odd formatting in the document, I wanted this published asap since it might be of interest to all Tado X users.
-
Tado X and Vitodens 050-W BPJD OpenTherm
Hello, Today I received and installed Tado X and Bridge to control my Vitodens 050-W BPJD. I used the cabling suggested by the app Relay pin NO/COM and it works. Later I found this post here that seems to confirm the boiler supports OpenTherm. My questions are: 1 - do I have to move cables from Relay to OpenTherm…