Hello, I have just set-up successfully a Tado°X system based on Matter. Now I would like to add other devices which are not related to heating or temperature control for two reasons : To expand the Ma…
Hi All, Recently procured a Tado Starter Kit v3+ to replace a ESi ESRTP4RF+ thermostat. Just need a little help with the wiring. The ESi wiring attached has 4 wires Live, Neutral, COM and N/O. Where d…
My system has been setup for almost 2 years now without any major issues but in the last couple of days the response to a heat command or a simple blink is taking ages. I tested it throughout yesterda…
In a room with a V3+ TRV and a wireless temperature sensor, the new offline schedule feature seems to cause continual calls for heat (fires the boiler) when a TRV goes offline. This morning one of my …
I also have the same issue with geofencing not working. I raised this issue with Tado and got the following response Thank you for your patience. The target temperature increased 1 hour before you wer…
I have installed the wired thermostat but it doesn’t seem to control the boiler. I set a target temperature, but the boiler does not shut off once the target is reached - it carries on heating and pus…
Hi I have the original V1 beta which I have not used since probably 2019. I powered it up today and it said all components were offline. I then deleted the home so that I can add everything back again…
I have two Homes, and I installed new thermostats on tado° X radiators in my home. I have a V3 system in my company and I had to create a 2nd account. This causes complications especially with Geofenc…
Hi everyone, I'm in the process of replacing my old thermostat with a wired Tado V3, but I'm running into an issue. The old thermostat had just two wires connected to it, and following the manual inst…
Hi below is a working setup for a Worcester Bosch GreenStar 30i Combi Boiler using the Digital Interface EMS Connection to a seperate wireless tado thermostat in another room I hope others find it use…
Hi. I am confused and cannot seem to find an answer to my question as to if the Tado system does or does not use your home wifi. I have a Tado Bridge connected to my BT router ethernet port, I have a …
Hi there, we had a danfoss receiver installed previously and we replaced it with Tado. We followed the same wiring based on how the danfoss was wired and for a couple of days it was working fine. Afte…
Hi! Setup: all radiators with tado thermostatic valve + thermostat to control the heating start/stop Scenario: heating is on, last thermostatic valve reaches set temp and closes → thermostat should sw…
Slightly odd one perhaps but as I spent quite a bit of time researching whether tado could work for my home's heating setup and didn't find any clear answers I wanted to post for others to see that it…
Seeking advice. Have been a happy Tado user with a conventional heating system controlled by smart thermostat and trv’s for radiators and extension kit to add hot water control. Now moving to a combi …
Hi. I have just installed Tado X. I have a room with two radiators, each of which has a wireless smart thermostat X, but there in no wireless temperature sensor X in the room. I want one of the radiat…
Good day, I want to buy a Tado smart thermostat. I have a gas condensing boiler at home, brand Buderus logamax plus gb072-24k. I already bought one thermostat of another brand, which unfortunately cou…
Hi, Day 4 of our tado system up and running here. A few teething problems but so far OK. I've done some forum searching now and see the 'early start' function does not get a lot of love! So far the ro…
Hi all I currently have a Tado V3+ smart thermostat hard wired to a Tado V3+ Bridge. The location of the thermostat and wiring is historic and due to a remodelling of the house this thermostat is simp…
Hi I have ordered a Tado Wireless Smart Thermostat Starter Kit V3+ with Hot Water Control and currently have a “BOSS THERM” thermostat and receiver (looks just like a Siemens) connected to a Glow Worm…
help wired thermostat Logic Heat 15 Boiler I’m replacing my Therma Wired Thermostat with a Tado wired thermostat, need help with the wiring and set up.
Hi Everyone, I updated my old wired thermostat and programmer with Tado Smart V3+ wireless system (including smart radiator valves). I set individual temperatures in every rooms and I realized that my…
Hello chat, I'm looking into swapping my current BPT TH/124 with a tado X, but I'm unsure about the compatibility as I'm not finding a wiring diagram matching my thermostat. From what I'm seeing, it s…
Hi all, I am wondering if anyone has successfully got the following to work and if so, how? I am just at the point of giving up and returning the Tado Wired thermostats. So the background is: I recent…
When running V3 I had linked the bridge to Homekit and had a hot water option in home kit. Just in the process of adding my new X equipment to homekit and expected to see a matter code on the wireless…
My thermostat V3 does not recognize when it is mounted. When putting it on the socket at the radiator it just does nothing. How can I make it recognize that it was just mounted on the radiator to star…
Recently one of my radiator valves has not been following settings - in the settings I have it set that when I manually change the temperature it should do it for a set time. This wasn't happening and…
