-
Smart Thermostat Touch Buttons issues
I was having all kinds of issues with the touch buttons but now it getting worse. Sometimes they work properly while other times they seem to get stuck, for example when I want to reduce or increase the temperature by pressing once, it seems as if I keep pressing it and it goes to OFF or 25 respectively. The problem is…
-
Tado Thermostat X battery life
I have a Tado V2 Thermostat (I don't use any radiator valves as I have a small apartment). I'm very happy with it EXCEPT for the battery life. When the thermostat was new, Tado promised the batteries would last for 2 years. Very quickly, people (including me) started complaining that the batteries only lasted for a few…
-
3 zones plus hot water
Hello, I'm having trouble finding the right kit list. I currently have a house with 3 floors. With a Vaillant Ecotec 624 boiler. Each floor has a wired thermostat. There are 3 heating zones - one floor per zone. I also have a hot water cylinder so I need hot water control. After speaking with Tado sales, they recommended I…
-
Plug required?
Hi there, I recently purchased a Starter Kit VS, Wireless Smart Thermostat Incl Programmer with Hot Water Control My boiler is a Vailant EcoTEC Pro and I have previously not had a Thermostat. I have managed to set up the Thermostat and the Internet Bridge. My issue is with the Wireless Receiver. The instructions advise…
-
No connecting with each other
Got tado installed today, worked fine for a few hours and then started switching heating off, now the system/bridge etc wont connect with each other, any ideas?
-
Added VR33 to EcoTech Plus 937 and radiators heating all the time.
I have been running my EcoTech Plus 937 using eBUS from an Extension Kit for a couple of years without problem - apart from signal strength to TRVs. About to take the plunge on the Tado X discount offer but before spending nearly a grand I wanted to make sure I could still run the boiler with modulation so I ordered the…
-
Having Opentherm error issues with navien LCB700 oil combi boiler.
Hi, I just installed my Wireless Receiver, temp sensors and rad valves etc this evening, its too hot to test thoroughly as my house is so hot today the heating cant come as the rooms are all too warm. I managed to set one room half a degree warmer than it was (set to 25deg when room was at 24.5) and the boiler came on,…
-
Tado Installation
Hi 1 I have a Worcester green star heatslave II external 12/18 2 attached is a EPH R27 HW 2 Zone programmer 3 also a Draytec SCR I can’t find any clear instructions. Worryingly when I clicked for the instructions based on the boiler it says tado doesn’t work with it even though your website says it works with Worcester…
-
Which has priority
Hi, I'm a newbie at this and I have what may potentially be a stupid question, but here goes. I have on my system 2no. smart room stats and 8no. smart TRVs. All this is connected to my Worcester Greenstar Heatslave II oil fired boiler. I have left my original Worcester Comfort II RF roomstat and integral receiver in place…
-
Which adaptor for oventrop
Dear community, I recently bought the tado x thermostat and can´t find out which adapter I need for it to work. It is an oventrop valve. Can someone help? Thanks in advance.
-
Two systems
We have tado in our caravan and looking to install it in our home. Can you use the app to control both systems?
-
Tado X accessories and Google Nest Hub - 2nd gen.
So I bought Tado X smart radiator thermostats and since I have 2nd generation Google Nest Hub, I thought that I don’t need Tado X Bridge to connect these to my thread network. Google Nest works as border thread router. But it didn’t work for Tado so I had to buy the bridges. Is this expected? I thought thread and matter…
-
Can I use wireless thermostat
Hi, I have a Vailant ecotec 624 with a hot water tank unistore. I got two floors and two wired thermostats for each floor so two zones. The wired thermostat upstairs is in not great place and too close to hest source. Question is can I go for the wireless Tado x kit instead of wired which would allow me to move thermostat?…
-
Advice on new tado set up
I have the following existing setup Vaillant system boiler Megaflo Water based underfloor heating on ground floor and 4 radiators in 4 bedrooms on first floor and loft. Old Heatmiser system with UH2 wiring centre. the system is not networked. Ground floor has 4 rooms each with their own thermo - so 4 zones of UFH. the…
-
Has anyone installed the v3 on a vaillant ecotech pro 28 with two seperate thermostats
Currently have a wired honeywell thermostat in the living room to control downstairs and one in the bedroom to control upstairs. Wanting to switch to the wireless v3 but unsure how to wire the boiler if anyone could help
-
Issues installing thermostat on Nefit SmartLine HR 11/24
Hey guys, I have a little issues getting my Tado thermostat to actually turn on my boiler. I have a feeling I just need to configure the right settings into the Tado thermostat, but I can't find the right settings. I already tried to follow the installers guide (with no luck) and tried both the OpenTherm settings (D01 &…
-
Strange thermostat display
Well, Newbie here, but on a few occasions I’ve gotten strange display on my wireless thermostat, Now, compared to my wired thermostat, upstairs, the faceplate fits the base plate with no movement. Unlike the wireless thermostat the bottom clip doesn’t engage properly. Now, since the wire thermostat has terminals on the…
-
Heat pump optimiser x with myvaillant connect?
I have a vaillant heat pump that has been recently installed that has a myvaillant connect box connected to it. This allows live reading and web/app control of the programmer. It’s also required to access the heat pump tariff options with ovo. I can’t tell if this is plugged into the same port on the internal boiler unit…
-
Moved into a house with a missing Internet Bridge
Hello, I have just bought a house and moved in over the weekend just gone. We didn't have any instructions from the previous owner about how the hot water and heating system other than to use the Tado thermostat to control the temperature and turn the hot water on or off. On day one we went over to the thermostat to try…
-
Boiler not Firing, even-though wireless receiver is calling for heat
I have installed the Starter Kit V3+ with my Worcester Greenstar Boiler and have followed the instructions and managed to get all the wireless devices to be talking to each other. The Wireless Receiver has the LED’s on to indicate that it is calling for heat on the boiler, but the boiler is not firing and not heating the…
-
Individual geofencing workaround for specific requirement
I have read the various threads and appreciate that geofencing by person and for individual rooms is not coming soon or probably ever (V3+). I have a specific requirement and think I have a workaround. 5 bed home with 2-4 adults (depending on uni terms etc). I have set up the whole system over the last few years and am…
-
Why does my Tado not respond when I turn it off via the app. All links showing they are connected.
Why does my Tado not respond when I turn it off via the app. All links showing they are connected.
-
Graphs key
Hi Did a bit searching, but couldn’t find a definitive answer to what this symbol represents …
-
Tado x devices added to google home but wont work with voice commands.
Hi Just installed wired tado x thermostat and 6 tado x trv I have successfully added all items ms to google home and can control via google home app. I am also able to ask google home for humidity and temperature values of all devices but i am not able to change temperature via google assistant. Whenever I ask to set a…
-
Can Tado Receiver X be set to timed central heating and water?
I have a Worcester boiler with DT20RF controller which I can disconnect. I have the hot water and heating on a schedule. I can see that the HW can be scheduled with the Receiver X and app, but I cannot figure out what control the Receiver X has over the CH? Is it possible to schedule the heating?
-
Query re. Home and Away
Just a quick question, does the frost protection feature remain active when the system is set to “away?”
-
Tado X support for hot water?
I currently have a Nest controlling the radiators and hot water, and a Drayton programmer controlling 3 zones of underfloor heating. Both demand from the gas boiler independently. I think I’ve worked out that the V3+ supports this configuration with a wireless receiver and 3 wired thermostats. But am I right in thinking…
-
Underfloor heating compatibility list
Does anyone know of a tado compatibility list? I have an underfloor heating system that does not work with tado so I am looking into replacing the wiring units etc to something that does as the existing room stats are dumb, ugly and well just awful! Can't seem to find any kind of compatibility list so that I know what not…
-
Pairing WIRED thermostats
I've got 2 WIRED thermostats and a wireless receiver. Do I to pair each WIRED thermostat with the receiver?
-
Swapping two Salus Wireless RT520RF thermostats connected to Samsung Heat Pump to Tado V3
Hi there, I currently have two Salus Wireless RT520RF thermostats each connected to Salus receiver in the airing cupboard. One controls the downstairs central heating, the other the upstairs central heating. The downstairs receiver is wired into the upstairs receiver which is then wired in to the Samsung heat pump…