-
Tado X Offline
So I woke up today and found my whole system offline, I've tried resetting / factory reseeting everything to no prevail. Really not sure how to continue is this common with other users I am thinking of returning as I now have no way of controlling my heating in my house. I thought buying the tado x with matter support…
-
All tado devices suddenly offline
This morning all my tado V3 devices are suddenly offline. The internet connection is fine, and I have restarted the radio receiver but still everything is showing offline. I have paired the wireless thermostat as well. Any thoughts & suggestions welcomed Nick
-
Tado X devices randomly dropping off the network
I replaced my legacy Tado system with Tado X and I realised, that my devices randomly drop off Thread network. Never had that issue previously. Same location of bridge and end devices. They just drop off randomly but usually at least a couple of devices are offline. They are not even the furthest away devices from the…
-
Is it possible to disable schedule for a single room?
Setup: 9 smart thermostats distributed across 5 rooms. Every room has different schedules. The kids's room for example has two heating blocks during weekdays, from 6:30am to 7:30am and from 5pm to 7:30pm, with off blocks (14 °C frost protection) in between. This week the kids are away, and I want to disable the schedule…
-
Router problem with valves
Hi,i just bought tado x valves with tado x bridge.i bought i tp-link and a simcard. i followed the instructions,i can connect the bridge. When i try to connect the valve,it reports "matters credentials generated" and then "verify the connection to "my ssid". here it hangs for minutes then reports failed to connect. i…
-
Can't remove wall stat X from mounting plate
I wanted to reset a wall stat today by removing the batteries and could not removed it from the backplate. It unclips at the bottom ok but will not come away at the top. I have four and they are all the same. It seems as if I apply any more force it will break. Has anyone experienced this and found a solution? Is there a…
-
Worcester Bosch greenstar 8000 OpenTherm and Tado
Hi I have a Worcester Bosch greenstar 8000 combi boiler, and I was looking into using Tado to hopefully control it via the Opentherm connection. Has anyone managed to do this, if so how? Thanks Chris
-
Tado stopped calling for heat but the boiler continues to fire
Hi all. I've been having this intermittent issue with tado recently. Sometimes after all of my rooms are at the desired temperature tado stops calling for heat, but the boiler continues to fire and heat the radiators that do not have tado trvs on them. Has anyone encountered this problem before and how to resolve it Thanks
-
Thinking about a Tado system, questions
Hi, first post, please be gentle :) I'm looking to install a Tado V3+ system (probably) to give better control over the heating in our home, as currently we only have a simple timer/programmer, not even a thermostat for the main part of the house. The heating systems we have are: 1 - Viessman combi boiler, about 11 years…
-
Tado X
Can you please advise if the Tado X product is suited for our situation. We want to urgrade and better regulate our hot water and heating. We live in a 5 bedroomed house, currently it has 18 Radiators, 15 of which have old TRVs. The boiler is a Potterton Ultra with a separate water tank (Megaflow Cylinder). We have 1x…
-
Using Tado App - VIdeo suggestions please.
I'm trying to convince other trustees to let me install a Tado V3 2-zone system in our village hall and am looking for a SIMPLE YouTube video showing how to use the app. Most include talk of radiator thermostats, Air Comfort. Geo Location options etc which are not relevant and will only confuse. Failing that (or even as…
-
Tado X Installation Wiring - UK
Hi all - I have a question about UK wiring. I have a system boiler and I’m looking to install the wireless receiver. Current back plate has 5 wires - live, neutral and earth. Plus a black wire , and a grey wire which control the water/heating. I can’t find any clear instructions as to where these should be connected on the…
-
Iphone geolocation setting turn sometimes
The tracking option is turning off every week on my wifes iphone(11), after turning back it's working again for some time. Is that a common issue or it's uniqe?
-
Enable multiple smart schedules
During the week, we have various ways we want to smart schedule our radiators: If we're both in the office, then we don't want the heating on If I'm in the office, then we want the heating on but not in my partner's office If my partner's in the office, then we want the heating on but not in my office If we're both working…
-
Hot water not working? You need the room temperature sensor
I have just set up a tado system for my elderly mother. She has only 4 radiators and a hot water tank in a Y-plan configuration. I put smart TRVs on the radiators and they were working to plan, but the hot water did not work. The wifi receiver seemed to be refusing to configure to the Y-plan, reverting constantly to a…
-
Tado X radiator thermostat “unmounts” from radiator
So I’ve experienced this twice now in 2 different rooms. The thermostat suddenly thinks it is not mounted and the heat just rises like crazy. No one touched the thermostat or made any manual adjustments or anything. Only “warning” I get is looking in the app and seeing that a room is set to 20°C but actual temperature is…
-
Please, can anyone tell me why?
So I'm fine tuning my heating, and set my lounge to begin heating if the temperature falls below 16 degrees. I'm sitting here, it's 16.6 and warm enough for me right now, but the tado wired thermostat just turned on the heating. Why please?
-
Terminal block broke off
Hey everyone! During the installation of our new Smart Wired Thermostat X last night, the relevant terminal block broke off and the insight seems slightly damaged (see pictures). Is it possible to replace just that part? It seems to be a removable one.
-
Tado X TRV - Keeps asking to mount
I have a few smart TRV X’s and all work perfectly, except one. Quite often one of my radiators starts heating up a lot. On the app I notice it gets a fault and asks me to mount the smart TRV. Hold it for a few seconds and it mounts per the app instructions, and then it works perfectly again and temperature continues to…
-
Cannot get the internet bridge to connect through my TP-link router (EE sim)
I've had a Tado at home for years (bridge and wired thermostat) and never had any problems. We are trying to fit one in a Lodge with a Morco GB24 Series 3 boiler and need a V3 Tado as there's no room thermostat (receiver, bridge and room sensor). The bridge will not connect to the router (TP-Link TL-MR6400 with an EE Sim…
-
thermostat X LEDs
What to do so that the tado x thermostat shows the temperature permanently
-
Tado Heat x optimizer & Daikin Altherma R3
Hello, I have a Daikin Altherma R3 heat pump air to water. it has a lan adapter connected but unfortunately this adapter is very cumbersome to use and primarily to connect to, this makes it almost impossible to do minor changes in the heating schedule. due to this I am looking at the Heat X optimizer as a mean to get a…
-
Accessory is not reachable in Homekit
So my bridge lost connection with HomeKit. It works fine in the Tado app, I can access Home and Tado away from home so I know my network is fine. Can see Philips hue in HomeKit. I tried a reset and hard reset. I can see the bridge when I use camera and it grabs the numbers. I click the bridge and it says connecting, then…
-
Strange noise in the night
Hi all One of my tado radiator valves has been making a strange noise in the night (usually this one will be the only one on) this used to only be occasionally but it has got worse and is now every night. I have videod this and linked in here https://app.box.com/s/f2emw5eaau01s0lh00li9o0oumiy6ojs I have tried removing and…
-
Suggestion for Tado App: Ability to rename "Other Devices"
A suggestion for the next Tado app update from my side would be the ability to rename the individual Tado X Bridges and Tado X Receivers in the same way it is possible with the Smart Thermostats. Since i have two bridges and 6 Wireless Receivers (multizone setup) it gets tricky to know which one is which one without having…
-
Thermostat V3 cycles between on and off too often
I've noticed recently my Thermostat is opening and closing the relais quite often. The boiler activates for maybe a minute and then turns off again. This is not sufficient to get the water into the whole system. Yet, the care & protect is reporting it is 100% heating several rooms. This behaviour makes that the rooms are…
-
Can i set a maximum value for the heating water temperature?
I have a tado v3+ device. I connected the wireless receiver to the Ariston gas boiler via eBus. everything is going well, but the thermostat sometimes sets the heating water temperature too high. Is there a way to set a maximum temperature above which the heating water is not heated?
-
Vaillant and Hot Water
Got a Vaillant EcoTEC Plus VU30 CS/1-5 with a external hot water tank. My Tado v3 extension kit is connected to the ebus and is recognized by the boiler. In the boiler panel I cannot control the heating circuit (only can control in tado app) and it works ok. I configured the boiler in the app and in the thermostat to use…
-
EU tado with s plan ch +ufh
Hi all, 1st post here and trying to figure out.. I have not long done a renovation and installed a main eco30 combi, I also have a ufh wet system in my extension which hasn't been wired in, I have just installed 2 zone valves. I'm now at the point where I need to wire them up. Ch is one system through the house with tado…
-
What happened to my post?
I just posted https://community.tado.com/en-gb/discussion/26041/atdvanced-system-compatibility-and-boiler-modulation/ and it's not visible anywhere? What happened? Can an admin re-instate.