-
Boiler not turning off
We have a problem with our boiler. It seems to have lost connection to the tado system. Tado is not calling for hear but the boiler will not stop heating the radiators. The house got up to 26 degrees yesterday before we worked out how to turn it off. It wasn't heating the hot water tank though.
-
Water whooshing sound
Hi, we’ve had a new boiler and new Tado valves fitted. In some radiators, especially those if it’s just that you me radiator on, the water can be heard whooshing into the radiator. The pump has already been turned down to 70% and can’t be adjusted lower apparently (Ideal Vogue). Can anyone advise how to prevent the…
-
Tado Balance with an electric boiler
Hi, I would like the functionality of using the cost forecast of Octopus Agile for overheating my apartment prior to a high cost period. These seems to be the functionality of Tado Balance for heat pumps. However, I have an electric boiler. Would the Tado Balance service work with an electric boiler instead of a heat pump…
-
Schedule profiles
I have now had the tado system for nearly a week, and its certainly better than my old hive system. You guys have done a good job on it. However you (and every competitor) are missing what I believe is probably an important feature for many people, and I can say 100% would have made me choose to move to you years ago had…
-
Vokera vibe wiring
Hi I was fitting a tado to my brothers with the above combi, and when setting the tado up it couldn’t find the boiler model, do we email support for wiring instructions ? Thanks
-
Recommended Powerline Adapter
Hi, I am trying to improve the connection between my Wireless Receiver and my Internet Bridge as the connection seems to be being lost periodically. I have been advised to try connecting the Bridge to a Powerline Adapter to extend the range. Can anyone recommend one they have used to do this successfully in a three-storey…
-
Vaillant Ecotec Plus (VC 25CS/1-5) via ebus - Heating works but Hot Water does not
Hello Tado Community, I had to replace my boiler and my new one Vaillant Ecotec (VC 25CS/1-5) got connected via ebus properly - heating works as it should (although I will need to find a way to limit max flow temperature for better efficiency but that's a detail). The issue is with Hot Water as boiler seems not to care…
-
Vloerverwarming
Ik heb op mijn vloerverwarming een rasp thermostaat kraan en deze staat tussen de 24 - 24.5 - 25 graden De Tado maakt geen onderscheid tan vloerverwarming en radiatoren. In de praktijk staat de vloerverwarming aanzienlijk hoger Mijn vraag is om een keuze te kunnen maken naar vloerverwarming met een ander temperatuur…
-
Poor reliability with Bridge Connection
I used to be a real fan of Tado and recommend it to people but now because of recent reliability issues I’m definitely a detractor! Constant Bridge disconnection is the problem and has been for weeks now. For example, my Bridge had been working fine all day yesterday. But it disconnected over night again. So no heating…
-
Bridge lost cloud access after 4 years
Woke up this morning to no heating or hot water, looks like the bridge lost cloud access last night. I've tried: Rebooting my ONT (BT FTTP connection) - this was done after each other change Rebooting my router (which is a Huawei AX3 pro) - this was done after each other change Rebooting the bridge - this was done after…
-
EnergyIQ: Reminder Notification Preferences
Hi, Hopefully not the biggest amount of work for this one: It would be nice to be able to define “when” you want to get notified from Tado to submit an energy reading. For weekly notifications it could be specifying a day of week, for monthly a day of month, for quarterly or yearly selecting an initial date that…
-
Range of Internet Bridge / Multiple Bridges
I've recently bought a Tado Wired Smart Thermostat and 6 Smart Radiator Valves for use in my apartment, but came across an issue I wasn't expecting: I live in a 2 storey apartment with concrete construction and an unconventional plan, which means 3 of my Radiators are out of range of the Internet Bridge. I haven't been…
-
Connectivity issues with smart radiator thermostats
I'm joining many others in my opinion that havng all radiator thermostats centered on a single Bridge is dumb and not applicable for anything but the smallest single-floor houses or appartments. I have a modular house built with reinforced concrete and have been struggling to find a placement for the Internet Bridge that…
-
Wireless Receiver and Internet Bridge keep dropping out
Hi, I posted a question previously about my Internet bridge and wireless receiver losing connection but my trv's still being active and heating according to the schedule. They keep dropping out, which means we are unable to adjust temperatures until everything is reset and connectivity is resumed. The Internet bridge is…
-
Internet Bridge with PoE
Would love to see the Tado Internet Bridge with Power over Ethernet. This could save us an additional cable because everything can be done with the Ethernet cable. Since the raspberry pi and many other similar devices can do it, this should be an easy task for Tado.
-
Tado graph key
Hi all, does anyone have a definitive list of the symbols used in the Tado graph. I’ve searched the help articles but they don’t go into detail. In particular there is a turquoise symbol of a house with a line through it that I can’t find the meaning for. I’m also under how to post a picture in this forum!
-
Tado Smart AC V3 and HomeKit - only off/cool, no way to set heat mode
The title tells it all: I can only turn off and set AC to Cool mode, but not Heat mode in Apple Home. In Tado own app I can set all modes. What am I doing wrong? Thanks!
-
Support 2 point calibration for adjusting temperature offset (Temperature Guesstimate)
It would be very helpful to enable 2 point calibration for adjusting the temperature measurement to match the middle of the room. Scenario as follows: At low temperature the thermostat reads the same as the temperature measured in the middle of the room e.g. 15°C so no offset required but at higher temperature the…
-
Does Tado (wired) work as a dumb thermostat without the bridge?
I'm just curious, if anything happens to my bridge, e.g. my cat chews through the wires, can I still control my heating (temperature, on/off) using the wired Tado thermostat?
-
tado + MCZ
Bonjour, J'ai un poêle a pellets de Marque MCZ avec une télécommande infrarouge ou on peut gérer la température est ce que TADO fonctionnerais dessus? Merci de votre retour
-
Intelligent Climate Control Device V3+" as an External Temperature Sensor for Thermostatic Valves
The "Intelligent Climate Control Device V3+" should be able to be associated with the same room as a thermostatic valve and be chosen as the reference for the external temperature. This can be done similarly to how it is done with a second thermostatic valve, an external temperature sensor, or the thermostat. If present in…
-
Can I completely remove the old time clock?
Hi, I am sure this has been discussed many times, I have read numerous threads but I cannot see any with my specific setup... I have a 3 zone plus hot water system, currently time managed by a Timeguard 7 day 4 zone controller and 3 wired room stats controlling 3 motorised valves. A 4th motorised valve controls hot water.…
-
Will these work or conflict with Google Nest thermostat
Will these work or conflict with Google Nest thermostat?
-
Multiple Smart Thermostat config
We have an existing Tado installation with most (but not all) rooms having Smart Radiator thermostats & Smart thermostats. Currently, all of the smart thermostats can call for heat. I’m thinking of modifying this setup so only the more frequently used rooms can call for heat, and lesser used rooms will only be heated when…
-
Tado smart thermostat compatibility
I have a Worcester Bosch 4000 combi boiler I want to now if tado smart stat is compatible with my boiler and what features I can use of it
-
New Tado installation
Hi Electrician just left, all test setup correct but no c/h or hot water?8
-
Thermostat button not responding
Hi, The buttons on my thermostat aren't responding to touch even though the battery is showing as good and the blink test works? Please advise. Kind regards
-
Flashing Orange Power LED on Wireless Receiver - Heating On
Hi All, Last night for the first time ever, the heading was stuck on and could not be turned off from my phone or thermostat. The Power Led on the wireless receiver was flashing orange, and the LED indicting the reciever was calling for heat was also on. I had to toggle the call for heat on and off manually from the…
-
Boiler always on
I've installed the wireless receiver as per instructions. The system used to have another thermostat system so these were the only wires I could change over. It all looks correct to me, but the boiler is constantly on, even though Tado says it is off. Any help appreciated. Or have I got a faulty wireless receiver?
-
Installation - Bridging the old wireless thermostat receiver
Help! Installing Tado V3 today. HW works fine but I am unable to find instruction on bypassing my old wireless CH thermostat receiver to enable TADO control of the boiler for CH. Receiver is a Plumb Center BDR91 (see photos). Exam question is which wires do I join and which should I blank off? (frustratingly not covered in…