-
My app keeps saying “open window detected” but all windows are closed
Hi all My app started to send me notifications about open window detections but there is no windows open. It has been a very cold night in Denmark and the thermostat is close to a large window, could that be the reason? Although, I also have another thermostat close to a big windows that does not say anything. I tried to…
-
TADO works as a Relay System or Modulating?
Hello, I have a Logic combi esp1 35 boiler which was controlled by a Danfoss tp5001 wired thermostat. The thermostat had only two wires, COM and NO. Its manual states it is an "On/Off load compensation thermostat". The boiler has a "Fully modulating operation to low outputs" (from the manual). The manuals state that both…
-
Tado energie-zuinig?
Tado presenteert zich als de oplossing voor teveel energieverbruik. Alleen de temperaturen die jullie adviseren (de voor-ingestelde temperaturen, maar ook die geadviseerde temperatuur in de tab klimaatcomfort), zijn hoger dan de in nederland geadviseerde 19 graden. Lijkt mij niet erg energie-zuinig. Als bv mijn woonkamer…
-
Tado to Worcester Bosch GreenStar 30i Digital Interface EMS Connection Bus (Working Setup Attached)
Hi below is a working setup for a Worcester Bosch GreenStar 30i Combi Boiler using the Digital Interface EMS Connection to a seperate wireless tado thermostat in another room I hope others find it useful Basically I removed my old Hive connection and receiver altogether from the boiler before i started on setting up Tado I…
-
Replacing Mechanical Timer + Thermostat
Hi I have a mechanical timer controlling both hot water and heating. I also have a wired thermostat for the heating. Images attached. Can I replace my current system with the Tado V3+ with Hot water control(or any other Tado thermostat ??). And can I do that on my own or I need an expert? Are there any instructions or…
-
Manual adjust graph axis
I would like to be able to adjust the axis of the temperature graphs in the Tado app. Currently this goes automatically hence graph axes jump every day and is different for each room. That makes it difficult to compare different days or rooms and makes it difficult to observe how quickly a room heats up or cools down. I…
-
Raam open
Ik wil zelf kunnen aangeven dat de raam open staat. Hij detecteert niet dat het open staat. Als ik zelf opgeef dan wil ik ook tijdsduur meegeven voor hoelang ik denk dat het raam nog openstaat
-
Schema - zomer / winter
Wanneer het winter wordt, wil ik overschakelen van een “zomer” schema naar “winter” schema ipv alles moeten aanpassen
-
Help! Wireless start kit v3+ installation
Please help! So sorry if this is silly but I am very confused and unsure if I have bought the wrong kit. I have a Worcester Greenstar CDi classic boiler and Digistat Optimiser and have bought the Tado wireless start kit with radiator valves. I have someone coming to fit for me but was looking through the box beforehand and…
-
Switching on/off based on humidity
Hello, It would be grate if we could have a function in the app where one can choose to switch on or off based on humidity. For example: if humidity reaches 60% switch on to 23C till humidity is lower then 60% or another value
-
Humidity trigger
I think it would be nice to have a humidity trigger as well as temperature trigger. As an example I have a TRV in the basement where the desired humidity is btw 60-70 and the temperature is not really important. It would be great if the TRV kicks in when the humidity is as an example above 70
-
Humidity smart action trigger
Is there a way to set trigger for when humidity is at the set level to send notification via Alexa or Google or any third party integration? Ideal would be to look at the humidity inside and compare to weather forecast humidity level and if outside is lower than inside send notification to Smart home devices or phone to…
-
Can an Extension Kit do a ZeroVolt link ?
Can the Extension Kit give a ZeroVolt Volt Free connection ? Basically, if a boiler needs two pins to be shorted out to fire the boiler, can the Extension kit do such a connection, or does it just send 230v down one link ?
-
Bye Bye tado
Well. tado is no longer in control of my heating. The final straw was someone in their support team pushing a new configuration that completely broke the system. Smart Thermostats: (both) constantly show Configuration Download icon. Internet Bridge: When powered up or reset, goes through the normal cycles, then ends with…
-
Comfort setting rather than temperature
As an option, why do we need to set a temperature at all? Why don't we set air comfort instead. I really couldn't care what the temperature is per room, the figure is irrelevant to me, I just want it to be "pleasant" in each room. Given the temperature to achieve "pleasant" can change depending on humidity etc it would be…
-
Extend open window time
Is it possibile to extend or to modify the open window time? So when you are doing the spring cleaning or leaving the window open due fry smell (in the kitchen) leaving longer then 15 minutes? And having a smooth warm up after the windows are closes
-
Anyone used this Opentherm Adaptor with the TADO Thermostat?
Hi, Im trying to convert my new Bosch Worcester 8000 Life to use Opentherm (or any modulating interface) with TADO. Nest users have pointed to this adaptor which converts the EMS in the boiler to Opentherm that can be read by a Nest V3. Just wondering if this also applies to TADO?
-
Heating still on when all TRVs off
Hi. Tado support recently updated my config so all TRVs have the extension kit as a zone controller. This was in response to a situation when a call to heat for one bedroom radiator would result in a lounge radiator also heating. I was told it was because the bedroom radiator had the wrong zone controller, which was a…
-
Setup question
Hi, just looking for some advice on a setup for a newly renovated house. im having a WB boiler with separate water tank. looking to control UFH with three zones then heating to std rads in the rest of the house(will add in tado trvs at some point) could someone advise what kit would be needed. thanks for the help
-
Radiator Thermostat not keeping target temperature
I just got a new wireless thermostat+ smart radiator valves for the different rooms. The issue is that the rooms heat up to the target temperature at the beginning of the schedule/ when turned on manually, but then fail to keep the target temperature. My flat is extremely poorly insulated, so the temperature drops markedly…
-
Heat transfer profiles to choose from
My old Honeywell thermostat had 4 profiles I could choose from. Each profile represented a different type of heat transfer speed. For example, hot air heating is a quick heating method. Convector heating a slower one. Both have their cons and pros. What currently happens is that when you use the Tado thermostat for hot…
-
How can I stop my boiler firing all the time?
4 bed house Two zones: underfloor heating wired thermostat; regular radiators wireless thermostat Got this set up working well with the zones independent of each other. Happy! Condenser boiler. Decided to add some TRVs to control some rooms on Monday. And I’m less happy! 1x study only used in the day so set at low temp in…
-
Schedule not always starting heating - Tado support says my system is problem
Hi, I contacted support because in the last 10 days or so, the Tado schedule is not triggering the boiler and I need to start the heating manually. Tado support have said absolutely no problems on their side. They are asking me to do lots of resetting, moving the bridge and even changing the router, is it worth me doing…
-
Cylinder, stat
Hi does anyone know if there will be a Tado cylinder stat in development?
-
Some radiators not turning off
Afternoon everyone. I’ve fitted Tado valves to most of my radiators but have had problems with three of them (8 are working fine). When I fit the Tado valves, they never manage to fully turn off the radiators. I’ve tried changing the temperature adjustment for them to see if I could fool the valve into closing completely,…
-
Diffret status for thermostats that are not linked to a zone
In order to stop a room calling for heat and switching on the boiler (like a toilet, closet etc) you can remove the zone controller for the room. It would be good to acknoladge this on the tile in the app.. currently regardless of the zone set for the room it will say "heating to" i think the rooms that are assigned a zone…
-
Date scheduling
Hi, it will be a great opportunity to be able to schedule from starting date and end date, please. The away option is not an option I like to use because off security. What will happen if some one hack my Tado account, and they have full information that I am away. So please add the option to scheduling from starting date…
-
Add detailed status info to tado app for Wireless Receiver connection problems
I recently reported that the wireless link and error LEDs on my Wireless Receiver were often flashing together to indicate a lost connection. tado support said they have access to detailed connection status information with date / time of error events. This type of data would be very useful for us customers to help…
-
My app is saying my heating is offline and I'm away on holiday at the moment what can I do?
Have uninstalled the app and re installed but no joy. Anyone got any ideas? Am worried my pipes will freeze!
-
Get the status of the relay
I have 3 wired thermostats connected with Home Assistant (both clouyd and local by HomeKit). I would like to know the status of the thermostat relay. That is, if the thermostat is asking my stove to turn it on or off. In the app this information is absent (I don't understand why) and there are 3 waves that give an idea of…