-
Change comfort scale
I find 18C comfortable, yet Tado tells me that I’m cold (even 19.5C is considered cold, whereas it’s uncomfortably warm for me). I’d like to be able to change the comfort scale, so I’m not prompted to “put on a jumper”, “snuggle under a blanket”, or “turn the heating up”. When we’re meant to be saving energy and resources,…
-
Smart schedule is not working
I have added time blocks but it is not working Out of all the radiators we have I have set up 3 for the following morning None of them turned on Is there anything that I’m missing ? Please could you help?
-
Fault detection if no temperature change detected
If a room has an temperature increase demand but there is no change in temperature for a given time period a warning should be triggered by Tado. My boiler has an issue that it needs resetting Every soften I only find out after an hour so after i get cold. That the system is not working. But the Tado ‘care & protect’ tab…
-
Smart Trv disconnecting intermittently
Just installed 4 smart TRV's, and one of them keeps losing connection. Weird thing is that it is the one closest to the Internet bridge. During installation it had an E2 error, but I did not have time to fix straight away. Later when I went back to it the problem had disappeared. As I understand it, E2 problem is an issue…
-
Boiler not firing - Tado calling for heat
I’ve installed my Tado thermostat and extension kit correctly and followed all the steps to the letter in the instructions. Everything is connected in the app and seems to be working fine. However, when adjusting the temperature on the tado stat it makes a click and changes to heating but the boiler never fires. I’ve been…
-
Why have my Tado wired thermostats lost power (Com is dead)?
My Tado stopped working last night after a year without issue. None of the wired thermostats are sending a signal to the receiver (they no longer "click" when you call for heat). Hot water continues to work. This lead me to test the cables for power and they were all dead. Now in a very cold house, I switched the zone…
-
Swapping Salus RT510RF to Tado system
Hoping someone can help. I used to have Tado fitted at home until I replaced this with Heatmiser controls due to introducing underfloor heating. The Tado equipment I have is the Internet bridge to connect to the router, a Tado Extension kit and 2 x wired Smart Thermostats. My son has recently moved into his new home. The…
-
Question about temperature modulation
I’m looking to replace my old non-smart (wired) thermostat with a Tado (wired) thermostat and I’m confused about temperature modulation. I know very little about boilers, what I do know is that I have a Baxi 800 boiler installed in 2019 with some sort of weather sensor/compensation. If I swap my existing wired thermostat…
-
Reset of meter counter
Hi, I have recently got replacement of meter device from gas company, and it has counter "reset" to some value that is smaller than last value I have entered in application. Current support recommendation is to delete all past records, and to start over from time when this meter was installed - with loosing all history…
-
Price increase
I am shocked by tado raising the cost for the Auto Assist monthly plan, WITHOUT NOTICE!!, by more than 30 percent. Why??
-
Tado Valve Issue
Hi i have tado smart valves on 3 of my Rads and i noticed that now when i switch either my Living Room Rad on or the Bedroom Rad on the Toilet one comes on as well, also my kitchen one without a smart valve comes on all the time now as well which i had already noticed but it's just lately that i noticed the toilet one with…
-
Modify Limits of Room Temperature Control
Is it possible to modify the upper limit of the Heating Temperature in the Smart Thermostat (it is currently restricted to 25 degrees Centigrade)?
-
Is this normal?
Hello, I’m about to install the Tado wireless receiver, but it looks like the old Honeywell controller is directly installed on top of the junction box. Is this normal will it complicate the installation? Thank you
-
Radiators and pipes making noise since installing Tado
Hello all, Since I have installed the Tado system my radiators and pipes are making a lot of noise when they are being heated. Before we installed Tado we didn't hear a thing. At first I thought it had to do with air in the system so I bled out everything several times but the noise continues. Perhaps it has something to…
-
Can I run two bridges off one internet router?
Is there somebody who can help with the below points please. I have a tado system set up in my house, comprising of an extension kit, bridge and a smart thermostat. What I would like to do is fit the same system in the house next door which I also own. The house next door does not have any internet access, so I was hopping…
-
Has anyone had problems with their Drayton RT212 radiator valves?
Hi, we installed Tado thermostats on Drayton RT212 radiator valves about 3 years ago and two of the RT212 valves have just failed within a week of each other, they leak water when closed off. Plumber thinks that maybe the thermostats push the pin down so hard that they are causing the valves to break. Has anyone else had…
-
Volledig open, volledig gesloten instelling
Beste Tado, Het zou zeer handig zijn om een kleine instelling toe te voegen aan de instellingen voor de slimme radiatorknoppen. Namelijk een instelling dat hij volledig open gaat als er warmte vraag is, en volledig gesloten gaat als er geen warmte vraag meer is. Dus een instelling toevoegen voor niet stapsgewijs inregelen,…
-
Themed icon for Android app
Since Android 12 or 13 apps can provide a themed icon that blends in nicely with the new visuals by adapting to the current accent color. Could you please implement it for tado as well?
-
is it normal tado fires the boiler and circulates hot water when all rooms are at or over temp?
is it normal tado fires the boiler and circulates hot water when all rooms are at or over temperature?
-
Room settings
Tado setup as follows:- Extension kit connected to combi boiler via Opentherm. 2 “rooms” both with temp sensors and basic rad thermostats. “Downstairs” has 1 x temp sensor and 3 basic rad thermostats, “Bedroom” has 1 x temp sensor and 1 x basic rad thermostat. In both rooms the temp sensor is the measuring device. The…
-
Smart Thermostat constantly heating
Hi Community. I'm new to TADO products and family. Couple of days ago I've replaced my Honeywell modular thermostat with TADO thermostat. Installation was quite simple and everything is working. But now my TADO thermostat is always heating. Temperature is set to 20 and current temp is 19.8, so it keep heating the system…
-
Heating Activity - Real Time
Hello, Whilst "Heating Activity" is good at showing which zone/room is currently heating, what is not in anywhere near real time is the Total Today value. It will sometimes take hours before the Total Today time changes when I know the heating has been on for more than the total of 11 minutes it has kept telling me.. I may…
-
Tado v3+ Glowworm 30cx
Hi I have a problem how to connect my new Tado v3+ to my boiler Glow Worm cx30. I've done receiver already but have problem where I suppose to connect four wires from receiver to boiler. Old one had just two wires. It was climapro2. Thanks for every tips
-
Smart thermostat all of a sudden stopped connecting
Hi all, Have had a pretty problem-free few years with Tado, event through changing boiler type, adding bits to the system, and the last year has been great. We have a fairly standard set up - smart wired thermostat controlling a combi boiler, and then individual radiator thermostats controlling each room. Works great.…
-
Wondering what kind of valve this is, and if I can get an adapter to work with it.
Hey all, I'm fitting smart TRV's all over the house, all done except one room, with three radiators, all with valves like this: https://ibb.co/m5Jj8nq https://ibb.co/sFQbfb6
-
Replacing 3 channels programmer - (2 zones) Rads, UFH and hot water
I am not an electrician or plumber but I did manage to replace my 3 channels programmer (Horstmann H37xl series 2 channel plus programmer) I have a S Plan system (can easily be identified if you have 2 pipes going to your valves). I have 3 valves for each of these Hot Water cylinder Radiators Underfloor heating I have 2…
-
Smaller increments for radiator thermostats
Hi, I run a couple of thermostats on my district heating system. The water temperature to the radiators is controlled by a PI-regulator, that does a good job. However, the Tado thermostats seems in daily operation to make quite dramatic changes to the waterflow through them, which means I see dramatic water temperarure…
-
Which adapter for Drayton 4 TRVs?
Which adapter if any do I need for Drayton 4 TRVs? Thanks
-
Is my smart radiator thermostat faulty - eating batteries?
One thermostat has consumed five times more batteries than others. I wondered if it was the radiator so I swapped this smart thermostat with another on a different radiator. It is still consuming batteries on the new radiator when the previous thermostat there was still on its original batteries. Looks to me like the fault…
-
Analog output different modes: a01, a02 etc…
Hello. I did connect a Siemens sas61.03 servo to tado and I can get this to move. I have a 24v power supply for the servo and a 10v one for tado analog power supply. Siemens servo is contrôles with a 0/10v analog signal. What is the meaning of the different analog options a01/a02…a015? Pid gain? . Thank you