-
iOS 16.3 HomePod Temperature Sensor
With iOS 16.3 HomePods can now relay temperature and humidity data to HomeKit. I’ve had trouble with the room heat being cold on one side, and the tado valve is near radiator… I’m using the HomePod for offsetting the room temperature, could this be automatic ?
-
2 heating zones plus hot water - guide unclear to me!
The guide included with the app doesn’t appear to clearly replicate my system. I have 3 heating zones in the house plus and unvented cylinder for hot water. Downstairs - Danfoss TP9000 which is a thermostat / programmer for both downstairs heating and hot water. It’s wired. Upstairs - Danfoss thermostat / programmer for…
-
After setting temp manually
After upping the temperature manually the stat seems to keep this setting until resume schedule is pressed on the app, (consequently often staying on all night) surly resuming the schedule at the next schedulde change would make more sense, does anybody know a way to make this happen
-
App should be able to shutoff manual settings of starterkit
For the use of Tado (starterkit) in rooms which cannot be accessed by you in person, such as; guestrooms, B&B, kids bedroom, other privacy sensitive situations, etc., it would be welcomed if the app can shut off the ability to change the roomtemperature manuallly. EG. We have a B&B and we have programmed the temperature…
-
Issues after updating to the new Wireless Temperature Sensor firmware
Today I have noticed one of my three Wireless Temperature Sensors is offline (noticeable in the app and as an error on the receiver). I started troubleshooting and I found out all the sensors have been updated to the new 204.1 firmware. I remember checking the firmware on Friday and it was still on 90.1 (still visible in…
-
Improve the temperature differential by applying a feedback loop
Every house is different. Boilers and plumbing is different. This leads to the temperature rising gradient being specific to each installation. So far so good? Now we often find a situation where a tado rad stat or room stat is set for, say, 18 degrees cent, but one later finds that the actual temperature is higher. It…
-
4 Zone System Boiler & OpenTherm
Hi All, Sorry for the long post... I have been using Tado for a good few years in our previous house which had a Valiant Combo and then a Viessman 111W and Tado worked well, we added Tado TRV's later on and it was great to be able to turn off the heating in rooms we were not using for additional savings. We have moved and…
-
Heating coming on when it shouldn't
Had heating on today, when I turned it off it came back on its own, app and wireless sensor says heating off, then WiFi and triangle lights started flashing in tado receiver, had to rest bridge for it to go back to off, concerned this would happen when not at home
-
Target temperature in graphs
Hi Really like the graphs of the heating profile throughout the day for each ‘zone’. However it would be great to see the target temperature (in a red line) on those profiles.
-
Tado and no modulation, or WorcesterBosch and no Tado?
Hi all. So I have a dilemma. I'd love to get a Tado system installed, but I own a WorcesterBosch Greenstar boiler. Reading historic posts in this forum it sees that WB don't allow or enable modulation using any thermostat except their own: So here's my choice: Get the nice Tado experience, but with only on/off…
-
Color of tiles
The color of the tiles is now fixed at blue/green till 18 deg and orange/red from 19 degrees. We never set the temperature above 18,5 and therefore the colors are always blue/green. It would be nice to be able to set other limits. Having different limit for bedroom and living room would also be nice.
-
Hide Tiles
On the homescreen there are tiles that I never use and would like to hide. It would be nice to be able to hide the following tiles: auto-assist, air comfort, energy IQ, Care & Protect.
-
Internet bridge won’t connect to new router
I’ve just got a brand new router. My bridge powers up fine, the router light only flashes for a few seconds and then goes off. Nothing happens after this. My Philips Hue bridge works fine, to rule out the Ethernet cable, i switched to the hue bridge cable but it still didn’t connect. I then plugged it back into my old…
-
tado General Enquiries
Anyone know how I talk to tado? Their help system doesn’t have a General Enquiry option (that I can see)…
-
How do I bypass Dragon Digistat+ whilst retaining Danfoss receiver?
Hoping this proves more helpful than Tado support have been on this occasion… I have just moved in to a new house and brought my old Tado system with me. The system in the new house comprises an Ideal boiler, LP241 controller, Drayton Digistat+ wireless thermostat, Lifestyle Wiring Centre and a Danfoss RX1 radio receiver…
-
Heating coming on with HW
We’ve been using Tado for a few years and recently had a new pressurised hot water system put in plus new underfloor heating in kitchen. Since then the central heating has been coming on when only hot water should be on. Any ideas?
-
Can only access1 of my 2 Tado accounts
I have 2 boiler somehow I have managed to create 2 accounts with 1 email but when I logged out from 2nd account to access the 1st (which I did) I can't access 2nd account at all. I do have other e mail addresses which Tado doen't recognise. What can I do?
-
Smart control of 11 UFH zones
Hi I wonder if there is any way to use Tado wireless kit to control 11 separate under floor heating zones? Today I have two Roth controllers, one with 5 zones and the other with 6 zones and everything controlled by 11 of their wireless thermostats. I would really like to make all of them "smart" and be able to control it…
-
Wireless receiver wifi and error lights blinking white.
Wireless receiver WiFi and error lights both blinking. Everything is working, I can control my heating and hot water. What does these lights both blinking mean? I’ve been unable to find any information about this. Thanks, Russ
-
Fitting Tado in Worcester boiler
I have a Worcester Greenstar Highflow 440 CDi boiler with an integral DT20RF programmer. Is it possible to fit a Tado programmer without interfering with the internal wiring of the boiler?
-
Which has priority
Hi, I'm a newbie at this and I have what may potentially be a stupid question, but here goes. I have on my system 2no. smart room stats and 8no. smart TRVs. All this is connected to my Worcester Greenstar Heatslave II oil fired boiler. I have left my original Worcester Comfort II RF roomstat and integral receiver in place…
-
How do I get my heating to work.
Tado has been brilliant for many years but the heating has become temperamental. I have tried pairing but the smart thermostat does not pair. My phone can talk to thermostat when programming but it seldom talks to the boiler. I have tried resetting and other things without luck. I have a different programme each day with…
-
My tado radiatorknob went offline now it is nott powering up
My radiator knob became offline. I tought it has a dead battery. Changed the batteries but never get a HI message. I tried different batteries but nothing changed.
-
Can I connect WiFi to my Internet bridge without a router?
I have recently purchased Three 4G MiFi broadband and the router has no connection ports, so I am having difficulty connecting to the WiFi.
-
TADO EU model - Opentherm + PDHW on a System Boiler with water tank
Hello... I have a system boiler and water tank. My boiler is IDEAL VOGUE MAX S18 which supports Opentherm and PDHW. The heating system is on S PLAN. My aim is to have Opentherm with Priority over Hot Water. Can TADO EU model archieve this? If NO, why not??? The PDHW on a S Plan requires the CH zone valve to be upgraded…
-
[Deleted]
[Replaced with a question]
-
I have a potterton pro max sl boiler with a Honeywell timer unit and a wired thermostat
I am wanting to know can I not just run the wireless thermostat for the heating and leave my timer on to control the Water? Was hoping to just swap the old t3 Honeywell home unit out and fit the Tado wireless starter unit? As the wiring to the old Honeywell timer is all over and doesn’t match any pictures I can see?
-
Hot water ok but no heat as of this evening (31/03/2024)
Hi folks, earlier today we noticed it getting colder in the house so checked the system, sure enough no heat. The boiler isn't turning on when heat is requested but does work ok for the hot water. Looking at the gas consumption the heating has only been on at around 4pm today. I should say the system has been installed for…
-
Assistance Needed with Tado Thermostat Setup for Two Zones
So we have the same situation here actually on two different houses, as they are family and they have both put under floor heating in their homes, and so we have the same challenge in both houses. We have bough a total of 4 Tado Starter kits, so have spent quite a bit of money. The challenge is: Combi boiler in both…
-
What A Hopeless System
Time to call it out. Tado is a pile of crap. The system is wholly unreliable and the company support is non-existent. Does anybody here think the company stands behind their product. It is 100% rubbish, if not worse.