Hi all, I’ve got a new build property with Therma txq0027, multi-room. Ch1 whole house, ch2 just does lounge, which is pointless, + hot water. The wiring looks identical to fit the Tado receiver (-ch2…
I have just installed the v3+ and the boiler will not fire up when heating is called for, hot water works fine. I replaced a British Gas wireless thermostat and programmer which was working fine, I ha…
so my smart thermostat is set to heat at 15.2 but for the last week the boiler seems to just be constantly on the thermostat now reads 23.2 and its still on. i have checked this against a thermometer …
I recently observed an issue with my Ideal Logic Code ESP1 38 where, despite setting the Tado Pro app to 80°C, Opentherm doesn't surpass 60°C. While this may seem positive, I encountered a problem whe…
I have one +/- 55 m2 open area with the following layout. On the right is the entrance with a door and a window. On the left a large sliding window towards the yard. I have 3 radiators, all three the …
Hi Experts, I am planning to move to tado. I kindly need to know which tado system would work best to control hot water and heating to the maximum benefit. I have a 20 years old heating system. This c…
Hi, I've bought new thermostats, but Tado don't provide install instructions to switch from the existing Therma thermostats as they aren't recognised by the online tool. Rather than wait 4-5 days for …
Hi I have tried to install wireless controller where previous controller was danfloss FP715si. I marked up all the wires and took off the old controller and there was a wire behind that was not connec…
I have just moved into a house with a Worcester Greenstar Compact with Comfort II RF and bought the tado kit required but the installation is beyond me. Thanks in advance.
No meaningful solution from Tado other than change batteries and restart. upping the temp on the app does not put the heating on as the command is not getting to the thermostat. been like this 4 days.…
Hi all, I'm looking for some advice. I have a new build property with a Logic H24 boiler in the garage and what appears to be a manual controller (for Frost?) next to it. The opentherm pins appear to …
I have a tado Starter Kit - Wired Smart Thermostat V3+. It's great, but the thermostat location is above a radiator and this is messing things up. Moving the thermostat would be really difficult and p…
Can anybody explain what I’m doing wrong? I’ve put the thermostat in my son’s room as he has a monitor in there with the temperature on too so that I can check. I’ve set it to be 21 degrees and the ta…
I've got a recent Baxi condensing boiler connected with Opentherm via the wireless remote kit that supports Opentherm. When any of the radiator valves call for heat the boiler is switched on almost im…
Hi Guys, I’ve been reading up on all the Tado stuff for the last few days and I think I know what I need but just wanted an opinion or two on whether I’m on the right lines before I go ahead and purch…
The API exposes a heating power section: "heatingPower": { "type": "PERCENTAGE", "percentage": 33, "timestamp": "2022-03-11T07:15:43.873Z" } This is presumably used to render the 1/2/3 flames in the U…
Hi there I've been studiously putting in my meter readings - every day in fact - in to Energy IQ. The problem is the estimated usage (and therefore cost) is totally wrong. What's going on and how do I…
Got a Tado V3 installation kit fitted it was the wireless thermostat I got and that was fine. But I bought 3 SRT's the wireless thermostat I put in my living room and when I fitted one of the SRT's to…
Hi, I’m trying to install the smart radiator valves. However, I’m having difficulty. I can screw the smaller section on the radiator, but unable to then fit the ‘smart section’s I think this is becaus…
Hi so I got the low battery email and checked the app and also reported there, so removed the head then the battery plate, left it for a minute then put the plate back on and fitted the head but the w…
Costo has a special offer on tado at the moment, I bought my system from them some years ago when there was a similar promotion . . . https://www.costco.co.uk/search?searchOption=uk-search-all&text=ta…
Newbie here so forgive me! Worcester greenstar 4000 boiler 3 years old, wireless 'Center' thermostat not operating despite battery change. Now looking at Screwfix: Tado V3+ Black Edition Wireless Heat…
Hi, I’m interested in moving to Tado but I’m not sure what kit to buy. I have a combination boiler heating system with a wired thermostat. It is not a combi boiler. I have a separate hot water tank. I…
Background I have the Heating controller + bridge + numerous TRVs and a couple of room thermostats. The Wifi environment is a mesh setup with 5 WiFi points / nodes to eradicate any dead spots. The Tad…
I have a simple system. Heating one room with the thermostat nearby. We are sitting warmly with the temperature nearly a degree above the set point and the heating suddenly tuns on. The explanation se…
I have a V3+ system with 1 Smart Thermostat and 6 TRV. I'm considering subscribing to the Auto-Assist, but I'm not sure how the subscription model works. Does my wife also need to buy it? What about k…
Hi, In the old version of the app you could go to Settings/Rooms/Smart AC Control and select Thermostatic or non-thermostatic mode. I am having an issue with my AC that may be related to the AC temper…
I have a Smart AC Smart Controller, I would like to shut down the AC when the room temperature reaches the target. I was able to do that last year with the Thermostatic Mode. Now this option has dissa…
I currently have 7 smart TRVs in different rooms, and there's a wireless temperature sensor in the hallway connected to the EU Combi boiler kit via Opentherm. I'm wondering if keeping the sensor in th…
