-
Viessman Vitodens and V3 thermostat boiler issue
I have a Viessman 100-W B1HF-M and a V3 Tado setup The bridge, hub and thermostat are all connected to the WiFi However when adjusting settings via the app or using the thermostat it doesn’t ‘call’ the boiler Link below is to an image of the current wiring. How do I fix this? https://ibb.co/9V93SHp
-
Wiring a Honeywell ml1 5sb
Hi I have an old Honeywell thermostat Wired identically to this one . My understanding is: Earth to P1 2 to P2 3 to NO 1 to COM Can anyone confirm this is correct?
-
reset tado v2
Hi how i reset a tado v2? i tried to touch with two finger the arrow but nothin appened bye
-
Black temperature sensor
Tado make a black thermostat, why not a black temperature sensor?
-
Fitting smart thermostat to M30 x 1.5mm valve head
I am fitting smart thermostat to a M30 x 1.5mm valve head (probably Myson) and getting error E2. This means no contact between the pin and the thermostat. Any ideas on how to resolve this?
-
Wiring Tado Wireless Controller to Joule Kodiak Tank and Samsung Gen 6 Heat Pump
Hi Just had a Samsung / Joule Air to Water Heat Pump Installed. At the moment its wired with the Samsung Wired Programmer setup, We purchased the Tado Wireless kit to work as the main thermostat for the central heating, and are hoping that it can also be used to give some control to the domestic hot water as well (This is…
-
Turn open window notification off
Is there a way to keep the open window Detection on (with 30 min timer) but avoid the notifications?
-
Install Tado on Vaillant ecoVIT plus VKS INT 196
Hello, is it possible to install a Tado smart thermostat (starter kit v3+) on a Vaillant ecoVIT plus VKS INT 196 ? And how? (Connections on the board, ebus...?) Cannot find any info about that. Thanks.
-
Thermostat & App no longer heating
Combi boiler. I proved everything worked fine when installed. Worked for a few days and has now stopped. I turned temp up in app and thermostat and neither kick boiler into heating. Pressing the manual override on the receiver only runs the heating for about 3-5min then it turns off. When in override mode the power light…
-
Care&Protect
It would be good to see how many times the boiler fires up for each room.
-
IMMERSION SWITCH BY TADO
I’m using a full tado system and love it 7 rad valves and 5 under floor heating zones (wet). So in the morning we use a lot of how water from tank it has run out yea the boiling kicks in Shen the stat temp gets low but would like to ad a 3kw immersion switch I know I can go and flick a switch but I want on the app possible…
-
Radiators turning on randomly
Hi all, Don’t know if it’s me just being stupid here.. I have scheduled my heating to come on for an hour a day in the morning to heat the house. I am finding that the radiators are hot at random points of the day also my tado app is saying that my heating is off. Any suggestions in what this could be, as the chat is…
-
Adding Underfloor Heating Systems
My house has a central heating system plus underfloor heating in 3 rooms. Can I bring the 3 x underfloor heating systems into my Toda environment as separate zones. So I would have 1 x room thermostat, 3 x smart radiator valves & 3 x underfloor heating controls - 7 zones in total. 2 of the underfloor heating systems are…
-
Radiator thermostat dead after battery change
Today I had two radiators with the message: low battery. So I decided to change them. I replaced the batteries in both radiator thermostats and only one came alive and the other is dead in the water. No lights, no nothing. Does anyone know how to reanimate the radiator thermostat? FYI: new batteries, tried to change…
-
Tado V3 Wired Starter Kit with Glowworm Essential 28c Boiler - Heating just stays on
Hello, I have installed and configured the wired starter kit with my Glowworm Essential 28c boiler but no matter what I have set in the app for the heating schedule, the boiler just stays on. I have: Wired the eBus terminations correctly. Registered the internet bridge, receiver and wireless temp sensor and they appear…
-
morco GB24 combi boiler
hi im looking for some help on how to wire the v3+ reciever to my morco GB24 combi boiler to control my heating thankyou
-
Tado if overshooting with new boiler
Hi, I recently swapped my old system boiler for a combi. I specifically got a boiler with opentherm so Tado could modulate it and that is all wired up and working fine. I’ve actually had my Tado for many years and have swore by it. But since swapping the boilers my rooms are always over shooting when they didn’t do that…
-
Heating in summer
hi do you turn off heating as the weather becomes warmer or as it’s set up just let it run and do its thing so if warm enough it stays off ?
-
Boiler burner coming on when Tado is off
Hi our gas usage has been incredibly high for a while now and been trying to get to the bottom of it. It feels like it is burning gas for way longer than it should. So I tested it with Tado when I turn off all the rooms and hot water. The boiler is still firing up and burner light is on. We have Tado wireless receiver…
-
Electric underfloor heating
When the thermostats were on sale in the summer I got another one with the intention of trying to replace the crappy thermostats that controls the electric underfloor heating in the bathroom. Forgot about it until I found it gathering dust in cupboard now. The previous owner installed this and we don’t have any technical…
-
Landlord control anonymous
Hi, I’ve had the Tado installed on basis that I can control remotely but my tenant (once found) can also control. Aim here is I can ultimately control and add/remove tenants to then manage accordingly. How ever I live next door and don’t want to share my contact details with tenant under fully managed or I’ll be opening…
-
Moved: Integrate wireless thermostat and smart radiator TRVs
This discussion has been moved.
-
Operating two boilers
Can I control two separate biolers in different properties with the same app?
-
Smart Thermostat not calling for heat
Hi, I have just installed two smart stats as an add on for a system installed last week. The original installation is all working and if one of the rad stats calls for heat it fires up the boiler but the two new ones don’t?…… Am I missing something or is there another reason?……🤷🏻♂️😉🌻
-
Tado support not responding
The support@tado.zendesk.com email has always been very responsive but I have sent two emails recently without a response. Has the support email address changed?
-
Tado Smart AC Control Constantly connecting and disconnecting from WiFi.
Hi, I have a Tado Smart AC Control that shows E04 on the display. It is constantly connecting to my WiFi network for 0s, and disconnecting, only to reconnect again and repeat the process. This is ridiculous behaviour. The reason it can't connect to the Tado servers, and why it's showing E04 is because there is no internet…
-
Setup help / programmer question
Hello All, Appreciate anyone's help in advance, and if anything below I have done wrong or need to do more. I have the v3 wired starter kit + 1 more wired thermostat. I have replaced 2 x Danfoss4000 thermostats (one updtairs bedroom and doenstairs hallway) with the tado wired ones. Was just COM TO COM AND NO TO NO. There…
-
[Feedback Request] Improvements to the Smart Schedule
Hi all, In the next weeks, we will start working on improvements to the Smart Schedule. We have some improvements in mind but we would be interested to get additional feedback from the community. Related topics:
-
Battery Replacement Period
I have a total of 8 tado radiator valves, all of which have the recommended Panasonic eneloop batteries fitted. The radiator valve fitted in the bathroom requires battery replacement every few weeks, whereas all of the others go for months on end before needing replacements. I have used different pairs of batteries, so…
-
Asking Siri to control heating
Is this possible and by what phrases as I’m trying “Siri turn hall on to 20° for one hour” ? Thanks