-
Tado not working 100%
Hi We have a tado V3+ that it not working, about twice a week, although the app shows the heating should be on (always in a morning) it's not coming on, it only works when I select the boost option. Any ideas would be welcome.
-
How to add hot water to existing Tado setup?
Hi all, Tado user since 2017 where have the following setup... EPH 3x channel/zone programmable control panel (2x CH & 1x HW) with a wired thermostat for downstairs and a wired thermostat for upstarts. I replaced both original wired thermostats with Tado wired thermostats, added Tado TRVs to most rads (not all) upstairs…
-
Distance between Thermostats (and Smarthub)
Hi I have a few thermostats in my house that I am planning to replace with Tado Wireless. 1) What is the max distance between Smarthub and the thermostats? 2) I will have 4 thermostats (wired) connected to the same hub, can that be a problem? Any minimum distance between the thermostats themselves so that the signals dont…
-
Vitodens 050 not firing up when App is calling for heat
I have had a Wireless thermostat fitted to a Viessmann Vitodens 050. The wiring matches the instructions. The reciever, bridge and thermostat are all connected to the WiFi and visible on the app. The app says the heating is heating to the set temp but the boiler is not on. DHW works as that is on a separate loop. When the…
-
Confused! Electrician couldn’t replace existing Thermostat with Wired Tado device?
Hi Everyone, So we have a new build property with an Ideal boiler which is capable of Opentherm and modulation. I purchased the Wired version of Tado as I read that it was capable of achieving this via digital set up. Electrician was round yesterday and when he took off the existing Thermostat, he mentioned that he could…
-
Wireless thermostat offline
Hi have just had new wireless v3+ installed, the bridge and controller are online but the wireless thermostat is off line, have tried pairing loads off times have reset, have moved the bridge but can’t get it online, any ideas?
-
Looking to swap out Myson MEP1c with Tado
App says to contact support so going down this route. Any help on the wiring for swapping these over? This controls the hot water and there are two wired thermostats for 2 zones that I need to replace
-
Tado - Not impressed
So got a new Tado system installed yesterday. Not impressed. 1x wall mounted smart thermostat (upstairs zone) - replaced old danfoss thermostat 1x wall mounted wireless temperature sensor (downstairs zone) - replaced old danfoss thermostat 1x Wireless receiver to replace old danfoss unit 1x Internet Bridge (wired directly…
-
Wired Smart Thermostat not working
I bought and installed Tado Starter Kit with Wireless Smart Thermostat to replace Danfoss TPOne-M controller for main central heating and hot water. That works fine but I also bought and installed a Tado Wired Smart Thermostat to replace a Danfoss TPOne-B which controls the heating only in our main bedroom. Unfortunately…
-
Boiler not firing up
I have the wireless receiver all set up but the boiler is not firing up when calling for heat
-
Relay or Ebus Modulation?
Issue The Tado was causing the boiler to enter Anti-Cycling mode. After speaking to Tado tech support, they have changed the Tado relay “to turn on once there is a heat request, and turn off once this heat request has been completely fulfilled”. Which seems to be working, but has caused greater peaks and troughs in the…
-
Smart TRV's
What is the difference between A Tado White TRV & Tado basic white smart radiator Thermostat
-
Is it possible to effectively use a tado extension kit to replace a three channel controller.
I have underfloor heating downstairs and radiators upstairs. I also have a hot water storage tank upstairs. The timings associated with the firing of the boiler are managed by a three channel controller (Horstmann ChannelPlus H37). I have installed tado smart thermostats in each room downstairs, set the 'downstairs'…
-
Tado to control a zone valve for underfloor heating?
Hello, we need your help to see if/how I can control an underfloor heating with our current Tado system. Situation We have a conventional boiler and a hot water tank. We have a wireless receive/extension near the hot water tank Our individual rads have Tado’s smart TRVs The problem is we have underfloor heating in a room…
-
Tado AC unit not turning off the AC
I've searched for this, but no one seems to have the same problem. I have a schedule set to turn my AC to heat every morning, and turn off at 7:30. However, most mornings the tado unit doesn't send the command to turn the AC off. The app shows it as off, but the tado never lights up to send the command. Annoyingly, because…
-
Ideal Combi Logic+ Wired Thermostat OpenTherm Installation
Hi All. I have an Ideal Logic+ 35 combo boiler and I've just installed the Wired Smart Thermostat starter kit v3+. I specifically chose this as both the boiler and the smart thermostat both support Opentherm. I had got confirmation from Tado that this combination would work before starting. Wow! It's been quite a journey…
-
Tado = Frustration! Ideal Logik ES1 35
Hi Everyone, So thanks to you lovely people, I managed to realised the Wired Thermostat was not infact suitable for my use case and therefore ended up purchasing the EU version to allow Opentherm and Modulation. I thought I was good! But behold, once everything was wired up, my boiler fails to call for heat! Went through…
-
Boiler too powerful/radiators noisy at night
I have four rooms controlled by tado. At night time when only one or two radiators in bedrooms are potentially heating at a time the radiators are too noisy(loud water flowing noise)- I assume as all the water is flowing through only the two rads. The others being off. This is an issue with boiler rather than the…
-
Noise during modulation
Hi, we have the baxi 830 combi using opentherm with tado and Drayton TRV's. If radiators are balanced they all heat up properly and radiators are quiet until the boiler modulates down as it starts to approach the target temperature. As soon as the boiler modulates down the longe rad for eg starts making a motor running…
-
Ideal Logic FU Fault - Tado Issue?!
Hi all, Recently we have had some issues with our Ideal Logic Boiler whistling / whirring as it fires up. It doesn't happen every time, but it's noticeable when it does, and it's started happening in the last few months. Initially we thought this was a boiler issue, despite the boiler only being two years old. We arranged…
-
Receiver issue
My room sensor and app is showing satisfied but the receiver is still indicating calling for heat and energising the connected zone valve
-
Installing Wireless thermostat kit v3+ on a Vaillant EcoTec Pro24 Boiler with SALUS Controller
Disclaimer: I am not an engineer, nor am I particularly skilled in anything plumbing or electrical. Essentially I'm layman with everything to do with boilers. I do however have a basic understanding of electronics, and I do like taking things part and solving an interesting problem Recently, I bought the Tado Wireless Kit…
-
Installing Tado V3+ - Firebird Oil Condenser
Hi I’m looking to install a Tado V3 to replace my existing boiler controls. It’s currently using an apt timer for control and it’s a bit dated. It’s a Firebird Envirogreen 20-26kwh Boilerhouse model. Has any one got experience of wiring up a Firebird boiler? I’d attach pictures but I can’t see how.
-
Oil condensing boiler using smart start?
Hi We have an old stone cottage, 2ft thick walls, old double glazing throughout and very little loft insulation. The system works quite we but I'd like to improve control of temperature on the house. We only have crads on the living room, from hall and bathroom. The Honeywell bimetallic strip star is in the unheated back…
-
Replacing old (2014) Tado with a new one- what's the process?
Quick one, suspect the answer is simple but I want to make sure I don't muck anything up and break the heating in my house. I have a 2014 Tado wired thermostat (amongst all the other tado bits I have in the house). It doesn't owe me anything- it's done sterling service to date. However the battery compartment has broken.…
-
Wiring the tado
Iv wired the tado best I could, please can someone confirm!!! Appreciate it 😁👍 Iv got a combi boiler, Baxi duo tec Blue wire to N Brown to L Grey to CH COM Black to CH NC Yellow/Green to CH NO
-
Wireless Receiver Hot Water 'call for heat' light stays ON
Just installed a Wireless V3+ with Hot Water Control. The Central Heating side is working perfectly but I think I've got a problem with the Hot Water control. On the Wireless Receiver, the Hot Water 'call for heat' light comes ON at the scheduled time but it remains ON until the end of the scheduled on time. The boiler…
-
Wireless receiver slow blink
My wireless receiver has started a type of occulting blink (more on than off) on the wireless connection light. I can’t find anything that says what this means. Can anybody help? It started after I activated the heating boost function to all devices.
-
Forgot my password
As I have forgotten my password, I have been trying to log in to my todo app all evening. with the link i Got sent it hasn't worked and I got an error message every time. Ihope you can help me. ps the product I have installed in the app is a tado ac Control :'(
-
Wiring Query
Today installed v3 Smart Tado Wireless Thermostat on Combi boiler with a salus RT500 rx. When looking at the Tado wiring instructions it shows a bridge required between L & COM for a Switched Live setup. However, my Salus setup had a bridge between L & NO which was neither the Tado suggestion for Switched Live or Potential…