Hi, I have five stats fitted and all been running fine for weeks, the last couple of days my sitting room stat is programmed to 16 degrees from midnight to 18.00 and then 21 degrees from 18.00 to midn…
Hello I have Starter Kit - Wireless Smart Thermostat [incl. Programmer with Hot Water Control] (V3+) and 4 Smart Radiator Thermostat. Could someone help me out I don't want the radiator thermostat to …
Hi, I currently have a new ideal logic+ combi boiler that is controlled by a Drayton Digistat+3. This is connected by 2 low voltage cables (Red = C / Yellow = On) there is also a blue wire that is not…
The lack of a range extender makes the tado system totally unsuitable for large or old houses. Wish I’d known this before I invested. What would the community have used had they known this before?
I'm looking to get a Viessmann 100-W and just wanted to confirm which kit I should get? I'm assuming I just need this to be up and running using Opentherm? I'm a bit sketchy on the difference between …
My heating thermostats have been running with no issues for over two years, only replacing batteries. Now one of the thermostats set at 21c is heating to 26.5 Why?
Hello! I have disconnected my tado V3+ cause to be honest i did not liked the way it worked,and to be more clear and on the matter of facts,i can tell you that after the instalation( bridge+ thermosta…
Hello. I have an old cottage with a new extension part. There are 2 modern Worcester boilers with wireless thermostats. One boiler does the old part of the house, one boiler does the new part. We have…
"Connecting to the server has failed. Please check your internet connection" On my phone I can't open the app, but if I go to the web and login to the tado site I can see that web app is connected and…
I'm struggling getting my extension kit to connect into my new Glow Worm Energy 35C boiler. The instructions show connecting the wires to the - and + connections of the extension kit, and the other en…
Hi Really not sure what I need to purchase to replace my following system. Current set up: Danfoss TP9000 in the cupboard with the hot water tan Danfoss TP4000 in the lounge downstairs (which controls…
Hi, Looking for guidance on this. I have 7 tado TRVs installed and am about to instal the receiver ( or whatever they call it ) so they call for heat. On my last system ( 8 years ago so I’m struggling…
Can see in another thread that someone found an update button in the HomeKit section. So us not using HomeKit can't FW update? Updates might be controlled by Tado then? Any reason forgot updating the …
Hi We have a 4 story new build house with UFH (2 Zones) in the lower ground floor and a zone per floor in the rest of the house. Each ‘floor zone’ has its own Digistat +3 thermostat in a room where on…
I live in a town house which as a 2 zone system. Zone 1 is ground and middle floor , zone 2 is top floor. My lounge I have added some TRV’s to create another zone (zone 1.1) If zone 1.1 TRV’s are call…
Hi! Can someone please tell me what the correct way to wire my tado is on my setup (Attached) I was thinking to do like this, but not really sure: Live to COM Neutral to P1 Output (by Live) to NO Many…
Hi, Since I upgraded to iOS 15, tvOS 15 etc, when I open the home app, all the smart thermostats are showing a temperature of 25 degrees. This is definitely not the case. I don't think HomeKit and the…
Hi, In my kitchen I have 2 radiators both fitted with smart rad thermostats. They are both in a tado room 'kitchen'. It seems one of the rads is coming on independent of the other. In my understanding…
Hi we are doing a renovation and putting NuHeat underfloor heating in the majority of downstairs but some of the rooms will only have radiators. Upstairs will all be radiators with 5 bedrooms and two …
Hi. Did anyone had issue with smart radiator valves? I have 5 of them for 2 years now and few of them once a few days when starting heating seems to freeze. I mean that they basically start buzzing lo…
Hi everyone. I tried to install my new smart ac control and unfortunately I cannot pass the stage of registering it. Every time I try it switches to registration through HomeKit and get stalled there …
Boiler is an IDEAL Logic ESP1 35KW combi boiler Thermostat controller is in the hallway, it is a DANFOSS TPONE-B Wiring to the thermotat looks like this, there are two wires, one brown one going to CO…
Hello all, I'm hoping to switch over from a Nest v2 setup to Tado in the coming months, So have a question about what equipment I need. Details on my current setup below: New build, brand-new heating …
So I have 2 tado thermostats (2zones) And I have skyQ tv with 2 additional mini boxes. When I’m watching a sky mini box. And the thermostat clicks on/off. The tv goes black. For about 20 seconds. Cutt…
I wonder if it is possible to somehow connect the tado system with the alarm system of the house. It would be very useful to set tado to away mode if the alam system is armed and set it to home mode i…
Hi, We're renovating our small kitchen and want to use a wet UFH system as there isn't space for an effective radiator. The rest of the house is all radiators in a single zone, powered by a combinatio…
As many of you know, tado is not working with HomeKit as long as it doesn’t allow to resume the heating schedules after any single change made with HomeKit. I understand tado likes to sell subscriptio…