-
Help why won't the heating switch off?
We've had tado since last winter and all has been working well. However now the main thermostat appears to be broken and unable to tell the boiler to stop. Its showing the temperature is 23.7. We have it set for 20.1... the radiators it controls are still on! Everything in the app looks ok... no errors and all connected. I…
-
How do i control the Megaflow
Hi all We, have Worcester system boiler (Greenstar 30i System ErP condensing boiler) with Megaflo unvented indirect cylinder -model 210i Central heating and Hot water is connected to Wireless Starter kit and two wireless thermostat- one for each floor The radiators are all connected to Tado radiator valves except the…
-
Worcester Bosch greenstar 8000 OpenTherm and Tado
Hi I have a Worcester Bosch greenstar 8000 combi boiler, and I was looking into using Tado to hopefully control it via the Opentherm connection. Has anyone managed to do this, if so how? Thanks Chris
-
What terminals for NTC sensor.
Hi there. Im about to connect my new wireless starterkit v3. But i seem to have a 2 wire NTC temperature sensor that works on a ohm restiance.. What terminals shall i use on my wireless reciver?
-
Trv mounting
Hi all, I've fitted a trv on my bathroom rail upside down as in the picture attache. However the display is upside down of the valve. How do I correct this?
-
Danfoss TPOne-M replacement with Tado Extension Kit on Logic Heat H24
Been waiting over a week for wiring help from Tado to no avail. I Know this is simple but in the absence of a diagram or labels I cannot wire on the backplate. Here is an image of the wiring. L and N are no problem but you can see a loop from L to COM (Brown) - one end in L but where does the other end go on the Tado and…
-
What devices I need?
Dear Community, I would like to use tado at my home but I couldn't find a similar layout in the forum, so I don't know which devices should I use or is it even possible to control my system with tado. This is my layout (and some planned devices). I have two separate heating zones: one for the radiators and a second one for…
-
Tado NOT safe! (valve fully open on low batteries)
A while ago I got a warning that the batteries are low on one of my devices for a radiator - and by the way battery life completely sucks with tado. They only last a couple of months - total lie in your docs that they can last up to 2 years… but anyway ! Apparently tado advertises that when batteries are too low, the valve…
-
Drayton Lp711
Hi, I have a Drayton Lp711 programmer wired to a Horstman Hrt3 thermostat. I would like to install my new wired smart thermostat but there was no instructions available on the tado app and I'm still waiting to here back from support. Just wondered if anyone had previously setup this configuration. Thanks :)
-
App schedule settings mismatch
The schedules that I see vs what have set for the devices is not matching
-
Roughly, how is my heating performance?
My room is 35m2, I set the temperature to 20-21C degree. Following is the graph of today. https://imgur.com/a/etZpoxP What do you think?
-
Opentherm behavior... how your boiler run?
I have a Viessmann 100 B1KC 35kw and is connected with the wireless receiver on +/- opentherm. Boiler is modulating and is ok,but at low heat request(1 wave) the boiler will not fire till at least 2-nd wave displayed and this time between 1-st and 2-nd level of heat request will ONLY run the pump and can't understand why…
-
Honeywell T3R
Hi we moved into a home with a honewell thermostat, and have found this not suited to us. I've tried upgrading to a tado but unfortunately spectacularly failed with a loud bang. Below is the current thermostat, the tado once wired up, and then the error message recieved. I can't seem to upload the images? Have I killed the…
-
Timer on boiler
Hello, I have a boiler (ideal i2 35) which has the timer, for setting when the boiler comes on, on the boiler itself. I have today installed the wired thermostat to replace the old one and although I can control the temperature I cannot control the timer. I tried having the boiler on constantly thinking Tado thermostat…
-
Import previous bills into Energy IQ on the app
Had a look around the community, but cant see anything on this. Is there a way import the previous years data into energy IQ bills area? I have the data in a .csv file already and would like to just squirt it into the app.
-
What happens when…?
If I get the thermostat, control unit and radiator valves (ie the whole thing) if the thermostat is at temperature (in the hall) but the office is not (from the radiator smart valve) will the boiler still kick in and run until the office is warm to the desired temp.
-
Can Tado help with this configuration
We have a children's nursery and so our radiators are in boxing to prevent burns. We have TRVs fitted to all the radiators but they don't work reliably because the heat inside the boxing is higher than it is in the room. Ideally, I'd like a wireless smart thermostat in each room that controls the radiator valves in that…
-
Bathroom Thermostat
My bathroom current has a Danfoss RMT230T thermostat located in the hall with a temeperature sensor in the bathroom itself. Can I replace the sensors in the bathroom with the Tado wireless temperature sensor and the Danfoss thermostat with a wired thermostat. Does the Tado temp sensor talk to the wired thermostat Pictures…
-
Tado Smart Thermostat - Worcester Bosch Greenstar CDI29
Hi, moved into a home a while back that had a wireless Hive. ALl that got removed just before we got the house (we told the woman we didnt need it as I was bringing my Tado with me). Well anyways, moved in and hooked the Wired Thermostat direct into the boiler where it worked fine for the last 15 months. Wiring was + Tado…
-
Hive and Tado
Hi, I have a Hive thermostat and Tado TRVs which are working really well, but I’ve been wondering if there is any advantage to going completely Tado and replacing the Hive thermostat? I’d appreciate anyone’s thoughts. Thanks.
-
Why can't I get a bearer token from the tado API
When I issue the command: "https://my.tado.com/api/v2/me?username=you@yourEmail.whatever&password=yourPassword" (without quotes and of coarse the right username and password) it succeeds in giving me an overview. But when I try to get a Bearer Token for using in futher requests with:…
-
Worcester bus connection
Hi, I bought a V3+ starter kit and some TRV valves to connect to my Worcester Greenstar 32cdi compact boiler. I wanted to modulate the boiler and thought I could do this using the bus connections. But the wireless receiver doesn’t have bus connections? It has park, P1 and P2. Can I use those or do I need an extension…
-
App down, reinstalled, no account data
App was not starting up anymore, reinstalled, and was prompted to sign in again. Upon doing so, no data were there. No home, thermostats, settings, previous data etc. Anybody an idea?
-
Can Tado work with my house?
We have just bought a house, and I would love to install a Tado system, just not 100% it would be compatible. We have an Ideal Vogue Max Combi 40, which is controlled by two Honeywell digital programmers. These split off into four ‘zones’. (Apologies for likely incorrect jargon- see attached photos for setup). There are…
-
Do I need to buy a receiver to replace existing wireless
Hi, I currently have an existing wireless receiver which is a Center EHE0200361 Wireless Programmer and the boiler is a Baxi 600 combi. The other wire is connected to a switch to turn on and off the boiler. I have brought the Tado° Wired Smart Thermostat Starter Kit V3+ The Smart Thermostat from amazon. Do I need to buy…
-
My wireless receiver says the heating is on yet the boiler is still off new install
Boiler is a Worcester greenstar 29 cdi Tado says to use just the L, N, and Grey wire. Isolating the black is this correct
-
Wiring question
Hello, I'm installing my Tado Wired Smart Thermostat from the starter kit v3+, but am running into issue with the wiring. The old thermostat is a Henco UFH-THERM24V-W and there are no instructions available in the app. Working with the instructions for the UFH-THERM24V-WD indicates only 2 wires are connected, but mine has…
-
TRV Accuracy
Hi I am relatively new to the Tado Eco system and am wondering how accurate the TRVs are. I appreciate they won’t be completely accurate for room temperature begin attached to the radiator but have placed a SwitchBot Temperature Sensor on top of the TRVs and get a variation of between .5C and 2C on different radiators.…
-
Are thermostat and wireless receiver sold separately?
Good afternoon, I currently use Tado smart radiator valves with my non Tado wireless thermostat. I am planning to upgrade to a full Tado system and replace my current thermostat. As I already have a Tado hub can I buy the thermostat and the wireless receiver separately? I can’t find them on the add on section of the shop,…
-
only one device showing in room
Hi, I have my thermostat and a radiator trv assigned to my living room with the thermostat set as the measuring device. Since configuring this I can't see the living room TRV on my home page so I am unable to make any remote adjustments. Is there a fix for this. Do I have to move the TRV out of the "living room" and create…