-
Grant Oil Boiler install
I would like to to install Tado (thermostats and TRV) on my setup, is this possible? Grant Oil Boiler for heating and hot water Various Drayton and Honeywell controllers Is this possible? Anyone done something similar? Regards, Mike
-
Anyone else replacing batteries on a regular basis
Seem to be replacing batteries across my 14 devices on a regular basis (Duracell and Energiser)
-
All TRV's disconnected but still heating
As title suggests, my wireless receiver is showing as not connected, so all my TRV's and display unit say offline. Thing is, they are still heating, and I can still see the days heating chart up to the current time. Is this normal? Do they continue to perform as normal, only responding to manual changes on the trv until I…
-
How to soften "graph readout"?
Would you be able to advise me on how to "soften graphs". I got living room downstairs which is on one thermostat and bedrooms upstairs on another. The readout in living room are very smooth and seems to be keeping a temperature running with just one heat wave once it reach its desired temperature. Bedroom on the other…
-
Wiring - Salus, Brotje, Hot Water
Hi Guys, Here is my setup: Smart Thermostat wired with Salus KL06 (Heating Module with 220V NC Valve) + PL06 (Pomp Module) for floor heating, Extension Kit wired with Brotje WHBS 22C, 12 x Smart Radiator, My problem is how to configure. it. Hot Water don't work, sometimes it stuck and even heating don't work. I tried…
-
Ideal logic combi esp30
Hi, Trying to set up the wireless v30 starter kit to an ideal logic combi esp 30. All wiring is correct as per the drawings. Tado is calling for heat and boiler is showing call. 230v present at s/l ..... Burner kicks in momentarily and then stops. Has anyone encountered this and solved the problem? Thanks
-
Tado thermostat doesn't response sometimes or set temperature on 25C.
Hello, Our Tado thermostat , hanging for al least 4 years, doesn't response very well. If we press the button, it displayes the temperature but then the button on the thermostat doesn't response. And if it response, it increase the temperatur directly to 25 C (from18 of 19C in steps, it looks like someone keep pressing the…
-
Valiant Combi Boiler Setting
Hi there Just moved into a new house with an existing Tado system. App working etc but just want to check what setting I should have the boiler at so that there’s no conflict. Should the boiler be set to On or Timed? Thanks in advance
-
Room temp doesn't match SRV temp.
I have an open-plan ground floor with two radiators, on at each end. Both have SRVs and are linked to the wired smart thermostat that is positioned at one end of the open plan room. The thermostat is set to 20c and the radiators are linked to it. However, the thermostat is struggling to hit 20, but the radiators are…
-
New install issues
Hi, I have recently installed a tado system in the house and have a few issues. The smart TRVs temperature inaccuracies are ridiculous and not consistent across the temperature range. I have 3 Govee temperature and humidity sensors all reading the same temperature as the Tado wireless thermostat. So no problem there. I…
-
Using tado API on OpenHAB
Hi To whom it may concern, I am looking forward to being/connected with tado smart Thermostat for commercial use. Our goal is to have access to API but unfortunately I read the FAQ and understood that you don't provide. Therefore I wanted to check if it is positive to use OpenHAB service for commercial use.
-
Boiler always on
Hi everyone, I installed a wireless smart thermostat today with no obvious problems. Reset the boiler after the power interruption. Set it to turn the heating and how water on which it did but when I’ve turned them down or off the boiler still seems to be on constantly. The wireless receiver isn’t showing lights that…
-
Why does my schedule not run without me having to turn the boiler/heating on?
I want to just leave my schedule on so that heating comes on and goes off at the set times. But it seems if I turn schedule on, it turns the boiler/heating on as well (the main on/off square on the app) Which defeats the purpose of scheduling.
-
Wireless Receiver - LEDs for Professional installers only?
Hello, I installed my Wireless starter kit today via the TADO app, replacing my Honeywell BDR91 attached to a Worcester Bosch Greenstar Combi boiler. All good and everything appears to be as it should be. However .... when I look at the "Manual for Professional Installers" leaflet, there is a stage - stage 6 Configuration…
-
New QUestion sent by Paologirola translated
sent to me by mistaked "Good evening everyone I'm new to the group I would like to have info on app tado I explain in my home I have two thermostat tado the first connected by wire for zone 1 while the second thermostat in wifi with actuator for second zone at the first test of operation all ok in the sense that I turned…
-
Energy IQ
Hi all, I have recently installed a Tado system along with 4 Wireless Thermostats. Which means that I don't have wireless TRVs in the aapre room, my office the two bathrooms and the kitchen. This means that when the heating comes on any of these 5 rooms will also come on. Until I replace all of them is there a way to get…
-
Initial Wireless receiver setup
TADO have told me my receiver is saying its connected to the relays on the boiler and not the digital - ive followed all their instructions and wired everything correctly. Is there a way to reset the receiver so that it picks up the correct instructions because last week just to test out its wireless connection i plugged…
-
Valve Adaptors
HI all ive got 5 radiators which are vaillant setup - the adaptors that then make this native with the TRVs are about 15 quid each - i note that VAILLANT Valve Adaptor Pack | Netatmo make plastic ones for a pound a pop - does anyone know if these would be compatible with the TADO TRVs as the thread appears similar but…
-
FAQ Group Created.
This is a test group - please let me know if its viable, and if not can it be placed elsewhere - first FAQ has been put there, FAQ GROUP — tado° Community
-
App Turning On Heating By Itself
Hi, Does anyone know why the app turns on the heating in my bedroom and living room by itself? I have a schedule set for 23 degrees between 7.30am And 8.30am. The rest of the time the schedule is set to 17 degrees. I don’t have any early start selected for the rooms. Just now I heard the relay on the thermostat click and…
-
Why is heating on based on schedule when "away" state has been set?
I'm confused by my heating switching on while away had been set many hours earlier. This afternoon the heating switched on to reach the set temperature of 19 degrees as configured in the "home" smart schedule. I expected heating to remain off because "away" state was configured which is set to heat only to maintain 14.5…
-
Heating turn off
Hi please can you let me know why my tado turns the heating off. I have not set it to do this, no window or door open. It seems to do it at random times. I have set time block please help
-
How to release thermostat from its mounting
My thermostat keeps rotating with its mounting so I can’t release it to change the batteries, I have this problem on at least 3 different thermostats and wondering if this is a common design or installation problem?
-
Access denied message when trying to add devices?
When I log into the Tado app, go to Settings, Rooms & Devices, and click Add devices, I am getting a message "Error - accessDenied" pop up. Is this happening to anyone else, and is there a way to fix it as Tado support doesn't work on Sundays. Thanks, Mark.
-
Complicated setup - will this work?!
Hi everyone In my house I have two zones (thermostats) that can individually turn on and call for heat from the boiler. #1 is day zone #2 is night zone Day zone has two rooms, night zone has 3 rooms. Every room has 1 radiator. Here’s what I’m thinking to do: ZONE 1 (DAY AREA) Room 1: - smart wired thermostat connected to…
-
Leaking towel rail since installing Tado on other rads
This may be a coincidence... Since installing Tado and smart thermostats on all my radiators (except one where the smart thermostat was DOA and is being replaced) the towel radiator in our bathroom has developed a leak. As the towel rad doesn't have a TRV (our plumber advised they shouldn't have..?) this is often the only…
-
Baxi Duo-Tec 28 HE A
I have just fitted everything up and all ok. Starter kit V3+. I have one question if anyone knows and is kind enough to help? My boiler has an FM/1 wireless receiver and wireless thermostat, do I need to remove it? There is nothing in the instructions that tells me anything? I know how to remove it, but not sure what to do…
-
Time schedule
My system can’t be off by the schedule few times.
-
2 TRV in the same room
Hello, I have a room with 2 radiators therfore I installed 2 TRVs, selected one as the "Measuring Device". My expectation was that based on the temperature measured by the "Measuring Device" both TRVs will open-close eactly at the same time and be set to the exactly same state, however I can feel that one radiator is warm…
-
TRV not calling for heat
Brand new install into an old house that I've recently moved into. Our Boiler is the garage, connected to an extension kit. Thermostat is in our kitchen, with two TVR radiators (TADO). All radiators else where in the house have Tado TVR - configured into seperate rooms / zones with single TRV / Radiators. All online and…