I've installed 4 x Smart Rad thermostats, and I've just installed 2 x basic rad thermostats. Am i right in saying the only difference is the digital display on the smart rad? My basic rad thermostats …
Hi, I've just installed an extension kit, bridge, and wireless thermostat but can't get any heating demand via toe digital connections. My boiler is quite old, but has digital terminals, labelled B B.…
I want to replace my Danfoss wired thermostat on a wet heating system with a Tado smart thermostat. I can find no information on whether this is possible. Any advice please?
Recently moved into a house and paired all of the devices that were left in the house. However, the hot water value is now always open but none of the smart thermostats are calling for heat. Any sugge…
Just about to extend my Tado system to the whole house. I have a Worcester Bosch condensing boiler with a wired thermostat. There is no by-pass circuit fitted in the plumbing. My Thermostat is Tado Sm…
Hi. I'm adding a second zone to my house controlled by a second valve in the CH system. I will install a second wired thermostat to control this valve (as I understand it you have to have a new wired …
Hi all, I have an interval xtreme boiler with built in RF. intergas say this is for opentherm communications with a Honeywell thermostat, will the Tado v3 be able to connect via RF or will I have to b…
I’m appalled that Tado only permits 15 minute blocks when setting the timer. Fine for central heating, but for hot water it means wasteful energy use. I need 5 or 10 minute blocks, twice a day, adding…
Please could someone help or give advice basically I have the tado kit. The thermostat does not heat up the radiators with the smart TRV they will only heat up via the app or manually. Is this system …
Has anyone had problems connecting the bridge to the BT hub 2? I have disabled the Smart Set Up as suggested, with no luck. I have proven the port on the router by connecting my laptop through it (all…
Hello all, I have Tado SRVs on all radiators in my home except for the two rads in the bathrooms wihch are always open. So whenever any SRV calls for heat, the bathroom rads also get heat. That's all …
tado° support comes in for a lot of flack on this forum but I want to add a note of praise. I recently had a difficulty where the CH relay in my wireless receiver was ignoring switch off commands, esp…
Hi, I moved the extender up in a cupboard (didn't unwire anything) but now nothing is working, the app says everything is connected, it's a traditional heating system, I'm not sure if something else h…
Can Tado be installed to service two boilers in the same property. So two smart thermostats with hot water control and run from the same acct? Has anyone done this? Was thinking could setup each on a …
Hi, I'm pretty much sold on picking up the Smart Wireless thermostat. I want to DIY install, but am after some advice before proceeding. I have a Honeywell ST6400C programmer (controlling central heat…
Dear tado community, I have a room with underfloor heating which currently is controlled via a manual control valve at the manifold (the manifold is located elsewhere in the building). I intend to rep…
Good day everyone, I have a daikin altherma bluevolution 6kW heat pump for several months now, next to it I have a 300 liter storage tank. My house has 3 floors with radiators and underfloor heating. …
HomeAssistant entity control features missing after upgraded the tado firmware. Before: Tado: Firmware: 59.6 ------------------- After: Tado: Firmware: 118.3 After upgrading the Tado firmware, at Tado…
Hot water is perfect but I need to bridge the BR1 receiver to allow Tado to control heating. Any idiots guides. Still waiting on Tado getting back to me. There are only 4 wires going to the back of it…
Hi, I have a Baxi Assure 30 currently wired to 2 Danfoss TPone thermostats. I am replacing them with tado v3 wired starter kit but the wiring points are different. I have N01 and N02 used in the curre…
Hi, brand new to this system. My App is showing the next change, to 18⁰ at 21:00, when I have set it to 5⁰ from midnight till 07:00. Programmed time to off is 21:00. Any idea where its picking up the …
My Tado wireless unit is newly installed. I am only getting lukewarm water from the hot water system. How to I get it back to the right temp (about 60 C)
I have two internet networks at home, one is Sky and the the other is Orbi. My question is if the network bridge is set up on one, does the receiver and all the TRVs etc need to be on the same network…
On the “Manual Control on Tado device” I have timer selected and set to 30 minutes but when I turn the hot water on for a boost it continues to the next schedule change. Is there something I am missin…
Hi I have been trying for 3 days now to install the new Tado system onto our boiler. An electrician hand plumber have installed the kit and I’m trying to connect all the thermostats to the bridge. It’…
Hello. I have a few properties available for rent, but please note that some of them lack internet connectivity. However, I can use my phone's internet to download all the necessary software during in…
Hi all, just installed a v3 package with hot water controls, can anybody explain what the purpose of the wireless wall thermostat is, as I understand it the wireless radiator valves control an individ…
