-
Why does it heat my house while I'm away?
I have Geofencing enabled. My schedule is set to start heating up on weekdays at 10am to 18.5c. My away setting is set to 10c. If I'm not home or if I leave home it does register me as being away, but it just heats up anyway. Strange thing is today it got to 16c and then held it there all day. It shows on the graph it was…
-
Boiler active and scheduling.
Hi all, I've just installed Tado with my combi boiler and added 8 SRVs to the radiators that previously had TRVs. however 3 still need valves fitting. Living Room - 2 SRVs + Room Thermostat Dining Room - 1 SRV + 1 Towel radiator (No TRV) Bedrooms, Hallway - 5 SRVs 2 Bathrooms - Towel Radiators (No TRV) I noticed last night…
-
Checking Tado is Right for us: Smart TRVs, UFH Control etc.
Hello, Currently in our house we have a Nest Learning Thermostat Third Generation for all the radiators in the house. For the two large family rooms downstairs we have replaced these radiators with water underfloor heating. This UFH runs from a single manifold in the garage and the two UFH rooms can be controlled and…
-
Local Weather programming
Idea local weather application on the software app. so that is heating is on inside and the temperature is hot/cold outside system can be aligned switch on/off cost and time saving for user of the Tado product this option would not need additional hardware only software and weather data.
-
My camera will not record my connection details
My camera does not record my registration details
-
Tado V3+ with wireless connection to Baxi Combi
Hi. New to all this. Just purchased a new build house and want to install Tado wireless V3+. I’ve followed install instructions via the app but when I turn the main power back on the boiler has no power. Found out the fuse has blown. Changed the fuse and the same thing happened again. Can anyone point me in the right…
-
UK Opentherm and wireless V3 kit
Hi, Ive started fitting the starter kit V3 along with wireless smart radiator TRVs. I have one customer who is asking why an opentherm connection has not been used when he has so say 'Smart' controls. His boiler is no longer modulating with weather compensation. Am I missing something in the setup?? Thanks
-
TRV Offline - Steps to Improve Connection
I just had my broadband router relocated and immediately the furthest TRV went offline, though my WiFi is OK in most of the house. Since it is the radiator that is complaining is it my broadband router or the Tado Internet Bridge I need to get closer to the radiator? If it's the Tado Internet Bridge does it have to connect…
-
Tado V3+ with Smart TRV's used with Tado V2 - are they compatible?
I am looking to upgrade my Tado V2 extension kit to the V3+ version, but I have a load of smart TRV's that I use with my current V2 extension kit. Would these TRV's be compatible with V3+ or do I need to buy new ones? Thanks in advance.
-
How long SHOULD a flow temp take to come up?
im gojng to seem thick again here. My combi boiler (without hot water tank) is rated to 24Ki have about 9 rads most are smaller but three bigs ones in three rooms with high ceilings that I know take about 90 mins to come up 2 degrees to temperature. My boiler flow temp after setback starts off at about 30 deg and in 15…
-
Radiator Thermostats
I have a house that has Tado TRV on all the radiators and thermostats in each of the major rooms to allow better temperature control. However recently I have found that the app shows rooms are heating despite temperatures being higher than requested. Initially, I thought it was an error and checked the radiator and it was…
-
Why is my system coming on?
In the last week the control unit has decided to turn around midnight even though no programmes are active. This sets the pump running but the boiler doesn’t fire because nothing has been requested but the smart thermostat.
-
Connections
Can anyone tell me if the wireless receiver connection HW NO should only have 240v when there is demand from the software?? Tech support won't answer this simple question...
-
How do wired thermostat and Tvr work together
I have a wired thermostat and was thinking of getting the radiator valves to go in other rooms. My question is, if the wired thermostat is not calling for heat as in off but the radiator valve want heat does the boiler come on and just heat that room. Or does the room thermostat have to be calling for heat for the radiator…
-
EU wireless receiver Opentherm not working
Just replaced my UK wireless receiver with EU version to get Opentherm... all wired as per boiler and Tado instructions and all looking OK on the Tado app, however when Tado called for heat the boiler didn't fire up! After much "googling" and head scratching I finally contacted Tado support (who were quick to respond btw)…
-
Sticking Tado room t/stat.
The t/stat repeatedly sticks on so the boiler is on all the time. Been advised by support to reset the bridge (so problem is known about although nothing on search). This works sometimes but not others so situation is such that I've replaced Tado t/stat with a manual t/stat which is of course very reliable. Very peed off…
-
Batterien
:s Ich habe ständig die Fehlermeldung mit den Batterien! Habe mehrmals die Kontakte gereinigt!!
-
Wireless receiver connections
I am getting a little desperate waiting for Tado to respond to my issue and wondered if any has experienced the problem. The output of my new receiver HW NO is permanently live, irrespective of the demand (can't switch off), tried everything, checked the S Plan wiring and it is correct, strange that the heating works fine…
-
V2 Tado upgrade to opentherm
I have a V2 currently wired to my boiler. However, the boiler needs to be replaced (Combi). I will be getting a boiler with opentherm option. Can I use the EU wireless receiver with my V2 on opentherm. Thanks
-
TRV on constant heat
Hi, I'm currently away for work, but my wife changed the batteries in one of the TRV's the other day. Since then, the radiator has been on constant heat. It is connected to the internet bridge, as I can see the updated heating chart, but changing the temperature manually on the valve or the app does nothing. I got her to…
-
Difference between models of SRV . . .
Does anyone know the difference between the Smart Radiator Thermostat V3+ Basic for Multi-Room Control @ £59.99 and the Add-on Smart Radiator Thermostat @ £74.99 ? I note the display on the V3+ is a bit altered from the original version but it seems a huge price difference for two devices which so far as I can see do…
-
Immergas Victrix tera 24 plus
Hello, I have Immegas Victrix tera 24 plus and I want to conenct it by eBus with Smart Thermostat V3+. If I tried it (I use + and -), Immergas didn't turn on (boiler has same port for relay and bus). Can you help me please?
-
We have dual zone heating using individual room TRV’s but hot water is not working
So yesterday we installed individual TRV’ on all radiators. So they work as individual zones (Tado sorted this). the hot water doesn’t seem to be working original set up was heating zone thermostat upstairs. Heating zone thermostat downstairs. And hot water via 1 timer controller anyone shed any light on how we get the hot…
-
Radiator balancing
1) Any thermometer suggestions for balancing radiators.? 2) Once you have smart TRVs is balancing still needed as they will regulate flow from the front end rather than the outlet from the rear end of the rad? cheers
-
Wrong reading
Hi, new to Tado. Only installed the smart TRV’s yesterday. I checked the app this morning and it said that one of my child’s radiators had almost 10kw output over night. And all other rooms had 0 output. That’s definitely not right. Is there any reason for this? Have I set it up wrong?
-
Tado TRV external temperature sensor - Home Assistant
I have recently bought TRV's for my house and I am not happy temperatures I am getting on the TRV's its not not accurate and offset isn't helping me. The only possible solution is an external temperature sensor but these are priced at £89.99 each!!!! too expensive and I will be returning my Tado system back for a refund if…
-
Manual Control Timer not working
I have just installed TADO TRV's and have been into the app and under settigns/rooms & devises/ under each room selected timer for the manual control. I have tested this and oddly this only seems to be working in 1 room, all the others are not timing out can anyone help
-
Boiler still firing after thermostat has reached its temperature
I have a wireless thermostat but have noticed in the last week or so that when the required temperature has been reached our boiler is still firing up. Obviously this is causing us to use more gas than normal, so expensive! The boiler is pretty much firing up all day but the house still feels quite cold. We've got it set…
-
Non thermostat radiators staying on
I recently installed three radiator valves and the wall thermostat all great. All the rest of the radiators except for three (two bathroom towel rails and one in an airing cupboard) have standard thermostats, and are set to be off. Following the instructions the existing Honeywell control has been set for heating to…
-
Pin Extenders - 20mm tip to thread
Hi, I'm trying to install a Smart Thermostatic Valve but I keep getting error E4. My TRV is a Siemens M28x1.5, I'm using the right adapter, however, the distance between the tip of the pin and the beginning of the valve thread is 20mm so I guess I need a different pin extender that is not included in the box, right? or am…