-
Boiler on icon
Is it possible to have an icon on the main app showing if the boiler is on off..
-
Care & Protect not working...
Hello. Due some glitch after electricity failure boiler was not responding to Tado "heat" command for over 23 hours... Temperature in our rooms was dropping down but system did not announce any issues... I would see this as typical example when Care&Protect should be alerted as usuall heating response is completely…
-
New internet bridge
Hi I recently moved into a house with Tado installed but no internet bridge. I’ve replaced this and downloaded the app. All says connected yet my heating isn’t coming on. What could I be doing wrong?
-
Radiator thermostat moving the valve pin in/out?
Hi I'm new in tado. I started to mount bridge, pairing main thermostat and for the start mounted two radiator thermostats. Everything looks fine, thermostats did a calibration, when i connected to my FAR thermostatic valves. OK, my boiler is off , main tado wired thermostat is not yet connected. But when i changing…
-
How do I use the app properly :-(?
I have just had my Tado installed and everything is connected and working fine. However, it just seems to ignore any schedule or instructions that I set on the app. The heating will not turn down or even turn off. My house is boiling!!!! Please help
-
USB cable
USB cable is very short on the v3+and would like to order a longer cable but I get confused with the various types ie usc c etc Can someone please advise me what I should order
-
Pairing light on bridge
Dear Tado Community, today I relocated the bridge to see if it would connect more efficiently with the receiver as recently the system keeps failing to switch off when it should - which kind of defeats the purpose of having it in the first place. So now, the bridge pairing light won't stop flashing, although the other…
-
Greenstar 30Cdi system boiler with diverter valve fitted
Hello everyone, I've spent a while searching through the forums to try and find a simple answer to my question, as the subject says, I have a Bosch Greenstar 30Cdi system boiler with the optional diverter valve and 'slide in' programmer fitted to control the heating of my unvented hot water tank. I purchased the V3+…
-
Hysterese afstelling
Kan iemand mij vertellen wat de Hysterese afstelling is,en of ik deze kan aanpassen?
-
Tado sometimes stops heating
I've had a few occasions recently where the TRVs are calling for heat, but they don't get it. I can resolve it by pressing the test button above the 3 wavey lines on the receiver next to the boiler. I don't need to intervene on the boiler. I have 11 rooms. It seems to happen every few days. It was working fine before…
-
Tado radiator thermostat doesn’t calibrate
I have one tado radiator thermostat that won’t calibrate. It used to work and been fully functional for over a year. It also only briefly flashes ‘Hi’ for a fraction of a second, when prompted by the app. The brightness of the display is also very low. The batteries have been changed. Any help would be appreciated.
-
HomeKit going to sleep?
I installed a v3 starter kit a few days ago. I seem to have a repeat issue where first thing in the morning the thermostat in HomeKit is status “no response” if I go into the Tado app everything is fine and I can control it. Once I turn it on through tado the thermostat becomes responsive through HomeKit and will stay…
-
Merge "deleted rooms" with a new room created
I have deleted a room and re-configured again due to malfunctioning radiator thermostat. Now in my "heating activity" dashboard it shows the history of this room in "deleted rooms". Is there any ways to merge this deleted room to the new one I've created so the statistics aren't disturbed?
-
2 zone setup with 2 wired thermostat and without boiler thremostat
Hi, I think it was discussed for a long time but search is hard. I am new to Tado, just bought 2 wired thermostat and 8 x Smart TRV which my house had 2 zones for Lower and Upper floor with a wired thermostat for each floor and a combi boiler without water tank. My question is when I installed the Tado TRV to the radiator,…
-
How to improve the learning of the thermostats?
I’ve had Tado installed for a year now and in the most part I like it. However, it is always overheating rooms. I have UFH in 3 zones and set it to 20°C. It will easily get past 23°C often. I thought the thermostats were learning? I’m just not sure why it isn't better at figuring when to turn off demand in our…
-
Wireless starter kit
Have replaced Drayton wireless thermostat and SCR receiver plus Honeywell 699. Hot water works ok but CH doesn’t work. It seems the thermostat/control unit just won’t trigger the boiler. Any thoughts? Thank you in advance.
-
Danfoss RAS C2 TRV Bodies Compatibility
Can I ask if anyone is still having issues with getting flow through SRVs when boiler is called. Have spent a considerable time with support getting valves opened and delaying boiler calls. If you have issues what type of valve do you have? I have new Danfoss RAS C2 and I understand that other systems have had to update…
-
Will tado work for my house?
I don’t know anything about heating systems. But my goal is managing the temperature of each room separately, make it comfortable and save money. I have Eneco district heat with Honeywell chronotherm IV in my leaving room. My house has 2 floors and 7 radiators (normal ones not floor). 1st floor 3 radiators - 2 in the…
-
Is my current setup compatible with tado ?
Dear all, I have a Siemens RDE100.1DHW thermostat. I use this to control my heating system and also have independent control to hot water (DHW). I want to replace it with a tado system. I believe the Wireless Smart Thermostat starter kit is the appropriate one due to separate DHW. My present thermostat works with batteries…
-
how to fix devices not talking to each other
I've run tado successfully here for five years. I don't remember doing anything unusual at the start of summer to switch anything in the system off. Hot water has run as expected over the summer. Today, switching a radiator on for the first time, there's no response. The iOS app shows everything connected, but when I…
-
New Tado installation, all working but...
Replaced Drayton wired thermostat and old controller with Tado Wireless V3+ along with 6 Smart Tado radiator valves. The boiler is a Grant 21E Oil boiler. The issue I have is the central heating pump is always on, the boiler however works when required, turning on and off as expected, just the water pump on 24*7. I have a…
-
No Heat! How do I fix it?
Hi All, I had someone install my tado v3 kit a few days ago. I have since found I have hot water but no heating. The App says it's on, and the light on the wireless reciever is on, but the pump in not pumping and the boiler is not firing. I have attached a picture of the current wiring. Can anybody tell me if this has been…
-
Question on modulation
Is it possible to see anywhere the temperatures that Tado is requesting from the boiler? I can see people posting them in some threads, but it's not clear to me where to get that information from. Thanks
-
Screw size for replacement
Hi, I've managed to lose one of the screws shown in the red box below. Does anyone know what size they are so I can get a replacement one from somewhere? Please disregard the wiring in this photo, the photo was taken when things were being moved around and tested. Thanks
-
Tado V3 User Open Window Detection Stopped Working When New Thermostats were Added
Hello Tado Owners, Help me understand what went wrong. I currently have Tado V3 bridge with 6 thermostats - 3 thermostats which are firmware v54.20 and 3 thermostats that I bought recently to add up which are firmware 95.10 I have the fully paid V3 app, with Auto-Assist enabled and Open Window Detection also enabled Up…
-
System calls for heat outwith schedule
Recent installation with 10 year old Worcester Bosch Greenstar boiler. System appears to be working well, however it generates spurious calls for heat outwith it’s scheduled on time, normally overnight. The preheat option is disabled, I have a Deco mesh Wi-Fi, through a cable modem. Any suggestions re cause or fix?
-
Explanation of the 3 Wavy Lines....???
Hi everyone, Earlier today I raised a question with Tado Support.... I have asked them to give me a 'definitive' explanation of Exactly what is happening when any of the 3 wavy lines are displayed.,,,,,,,,,ie 1 wavy line means.......??? 2 wavy lines means.....??? 3 wavy lines means.....??? There are actually a few possible…
-
Normal radiator TRV valve vs Tado smart TRV valve
I have 9 normal TRVs valve on 9 radiators. I am planning to have a tado° Wireless Smart Thermostat Starter Kit V3+ and just 1 tado° Smart TRV Thermostatic Radiator Valve. Will my other 8 radiators still heat up along with the one with tado smart radiator valve? Or I need to have Tado smart radiator valve in all radiators?…
-
Tado V3+ and Vaillant Ebus
Hi, I currently have a Tado V3+ wired starter kit coupled with Tado smart TRV's. I'm about to replace my boiler, will Tado modulate a Vaillant Ecotec Plus? Or am I better to stick with a pure Opentherm boiler like a Baxi or Viessman?
-
Energy IQ Meter Readings: New gas meter, restarts at zero
Hi, I've logged my gas meter reading in the Tado app in "Energy IQ => Meter Readings => Add" a few times each month. A few months ago, our gas meter had to be changed and the readings on our gas new gas meter now restarted at zero. Can I just put the zero and subsequent readings into Tado's Energy IQ Meter Readings, and…