-
Is it possible to increase the minimum opening size on the radiator valves?
Hi Sometimes my radiators are wheezing (not just with the Tado smart valves, but the old manual ones too), I think when most of them are closed and a few ones are barely open. Now this is not an issue with the manual valves, I just set them to an opening when they are not wheezing. Because Tado adjusts them automatically…
-
Vokera vibe wiring
Hi I was fitting a tado to my brothers with the above combi, and when setting the tado up it couldn’t find the boiler model, do we email support for wiring instructions ? Thanks
-
what is the correct way to connect my Tado wireless receiver to my Vokera Compact 29A combi boiler
a wiring diagram for my question would be very.helpfull. Cheers
-
Replacing RWB2
I’ve got an old Glow-worm Mastermind RWB2 which uses the industry standard back plate. Boiler is a Worcester Danesmoor 20/25 oil boiler. Room stat is a Honeywell T6620B. I can only see one 2 port valve in the airing cupboard, and for the heating to come on, the hot water must be on too. I believe it’s gravity fed. Would…
-
Heating and hot water on
Hello. I replace my old termostat today with tado v3. I follow the wireing method but for some reason the heating and hot water is on even if is turned off. So I play with that for a good few hours. But still. I have to put it back my previous termostat. Any idea
-
Voice commands
Hi, According to the tado docs, we can voice command "one or multiple rooms". What is the command for multiple rooms? Currently I have setup manual routines/automations in Google Home, e.g. "Boost all heating", "Boost upstairs heating", but these are just 'change set point' ones which is the same as manual control. Also,…
-
Painting thermostat casing with water based emulsion.
Would be interested to find out if anyone has successfully painted thermostat to blend with wall colour? Thanks.
-
Is it just me, or is the graphing broken?
Both online, and via the Android app, the option to display a graph of temp/humidity under the 'heating' icon now seems messed up. it no longer shows the rough times across the top etc. It appears all that is compressed into RH side... this is from the web but my phone is just the same.. sigh. I suspect this is since last…
-
Receiver signal quality
Hi, Is there any debug option to know the quality of the receiving signal? I´m so sure that the developers have something to know how well it works. Actually the used radios should provide the RSSI parameter. So, is there any way for user to access to these metrics for helping during the installation? Thanks
-
Can Tado replace a wireless Danfoss Icon (water based underfloor heating) system?
Hi, I’d like to replace two Danfoss Icon Thermostats I have with Tado, I have a water based underfloor heating system from Danfoss, two zones, and two wireless Danfoss Icon Thermostats. The Danfoss module controlling the heating system is connected to the Icon sender module via Ethernet / RJ45 cable, which is what I’m…
-
How to connect two devices to one tado
Hi. I am dealing with a situation at my home. I need my Tado to turn on the boiler and the pump. There will be all three possible situations. That means boiler heating and pump not running. Boiler heating and pump running. Boiler and pump turned off. I have three wires running from the thermostat to technical room. Is…
-
Help replacing British Gas UT1 and hard wired temperature control
I’m trying to install my Tado starter kit to replace my old British Gas UT1 model. The house has a combi boiler, wired to the UT1, with a separate hard wired temperature control. Pictures of wiring attached and also the wired temperature control. Please could you advise on how to wire my tado in successfully as following…
-
Confirmation of kit requirements.
Evening all, I have been lurking for a while and have two questions for those who have Worcester 2/ 4/ 8000 models, or whoever has knowledge of these. 1, given the option between Tado with eu for modulation or the Worcester easy control. What would you have ? I can get both for a similar prices £150 - £170 2, if I went…
-
Opentherm with Worcester 25i ERP (GC47-406-60)
Hiya all. I am looking to fit a wireless V3+ starter kit to a Worcester 25i ERP. I want to use OpenTherm connections and Tado compatibility says its OK with EMS-Bus but not EMS+ Bus. The boiler says its EMS but doesn't stat which? Any ideas? Thanks :-)
-
Replacing Honeywell devices
Hi, thinking of getting a tado device as one of my Honeywell displays has failed. in one room I have a Honeywell wireless thermostat with bdr91 receiver this controls the heating in the house. there is a wired Honeywell thermostat in the kitchen which controls under floor heating. this is all connected to a green star…
-
Moving from a Danfoss wired RET-230L thermostat to wired TADO thermostat
I currently have a Draytom LP522 controller which has 4 Danfoss RET-230L wired thermostats controlling four underfloor heating zones and I would like to replace the thermostats with Tado wired thermostats keeping the Drayton controller. The RET-230L has a 3 wire connection (4 if you count ground) as shown below. How would…
-
DHW controls doesn't work Vaillant combi
Hey, I have installed the wireless receiver, a V3+ module and radiators thermostats, a v3+ was configured with Vaillant EBUS, before I have the vr 940f receiver by Vaillant and it can control a temperature of flow for CH and DHW. For now I cannot control CH flow in the tado app and cannot control it on the boiler but…
-
Anyone had success using Tado radiator thermostats as google home automation starter?
I’ve been trying to use Tado readings as triggers for Google home automations but the readings are not available. The are though in IFTTT. Anyone had luck setting this in in google home?
-
Tado smart trv
Why do the smart trv’s cost more from Tado professional shop than off Tado shop, I have bought the Wireless Smart Thermostat Starter Kit V3+ as it has Modulation Control but can see no difference in the trv apart from the guarantee. Thanks
-
Why can't Home Assistant see TADO thermostats?
TADO working fine if individual STRVs are added to dashboards but where 2 x STRVs are controlled in TADO by the room stat in that room I cannot get the thermostat onto the dashboard. This means the zone temperature cannot be simply adjusted like a single STRV can. Looking for a fix by TADO!
-
Wireless Smart Thermostat V3 - Vitodens boiler - OpenTherm query
Hi - I have an Visseman Vitdodens 100 OpenTherm compatible boiler. OpenTherm updated their technology in 2021 and I want to know it the Wireless Smart Thermostat V3 supports the full latest Open Therm technology which was updated in 2021? I presume I need to get the EU version? If so, is there anything additional required?…
-
Greenstar 4000 Combi Boiler
Hi All, I have a Greenstar 4000 combi boiler and I'd like to use the digital connection to enable hot water pre-heating and control the heating via modulation. Is this possible with the Tado Wireless receiver (V3+)? If not is there a converter I can get for the Greenstar to make it talk OpenTherm and then connect it to the…
-
Vaillant Ecotec Plus 35KW - is it supported?
As titled - looking for the v3+ wireless kit.
-
Boiler keeping firing
Ever since I put in smart thermostats the gravity fed boiler keeps firing for approximately 20 secs every 4-5 mins. It’s not on a separate zone so is “always on” along with the two heating zones which the smart thermostats are on. Any thoughts?
-
Viessman Vitodens and V3 thermostat boiler issue
I have a Viessman 100-W B1HF-M and a V3 Tado setup The bridge, hub and thermostat are all connected to the WiFi However when adjusting settings via the app or using the thermostat it doesn’t ‘call’ the boiler Link below is to an image of the current wiring. How do I fix this? https://ibb.co/9V93SHp
-
Wiring a Honeywell ml1 5sb
Hi I have an old Honeywell thermostat Wired identically to this one . My understanding is: Earth to P1 2 to P2 3 to NO 1 to COM Can anyone confirm this is correct?
-
reset tado v2
Hi how i reset a tado v2? i tried to touch with two finger the arrow but nothin appened bye
-
Black temperature sensor
Tado make a black thermostat, why not a black temperature sensor?
-
Fitting smart thermostat to M30 x 1.5mm valve head
I am fitting smart thermostat to a M30 x 1.5mm valve head (probably Myson) and getting error E2. This means no contact between the pin and the thermostat. Any ideas on how to resolve this?
-
Wiring Tado Wireless Controller to Joule Kodiak Tank and Samsung Gen 6 Heat Pump
Hi Just had a Samsung / Joule Air to Water Heat Pump Installed. At the moment its wired with the Samsung Wired Programmer setup, We purchased the Tado Wireless kit to work as the main thermostat for the central heating, and are hoping that it can also be used to give some control to the domestic hot water as well (This is…