I've been using a full Tado system with TRVs in every room for a few years now but last night it did something new. The heating had been off for hours but the boiler mysteriously sprang to life and st…
Hi, I was looking to see if anyone has the same issue as me? I’m not sure if I am micro zoning too much? I have a 3 level house with really poor internal insulation between rooms. I have downstairs at…
Anyone know what’s going on here? All my rads (which have the smart trvs) are in night mode set to 12 degrees, all the room temps are currently above that, yet 1 rad is apparently calling for heat mak…
My heating is 1 tado thermostat and dumb trvs. So that controller controls every rad. The office is in the garage, i want to be able to turn the heating on and off for that room independently from the…
Hi, Can anyone help me confirm that the wiring on the boiler was done correctly by the installer? I have some doubts and just need some confirmation that it is correct. Below are the pics from the Tad…
Has anyone got any advice for this? After making a manual temperature change on the app, I assumed that it would revert to schedule at the next time change. I was dismayed to discover that the process…
About a year ago we moved into a new property and inherited an Ideal Logic combi boiler connected to a Tado smart heating system. As it's now getting colder, we're noticing a lack of central heating a…
I am replacing a Drayton Lifestyle 112 with a Tado Smart system including DHW. It controls a Vaillent Ecotec Plus 637 system boiler but there has never been a roomstat connected. I have everything els…
Hi there My hub, bridge and thermostat all say a firmware update is required and all show as connected and reachable, however when I click to update, it says accessory isn’t reachable? Neither works i…
Have just been through one of those nightmare "disconnection sequences" which I fear become part of the "life with tadoº" experience one becomes used to after living with the system for a few years. A…
Hi, appreciate some help. I have two heating zones, downstairs + hot water and upstairs. I have two 12v thermostats connected to a Heatmiser UH1 wiring centre. Can i connect a wireless receiver to zon…
Anyone has this yet, set temperature 16c and thermostat reports 18c and it is clearly over 18c but heat still on 100%. Did reset with removing battery, removing room all together and nothing helps, st…
I'm really hoping someone with experience can help out. I've had a Tado system installed since beginning of year all working no problems. Heating was turned off over the summer using the App, with the…
Hey fellow tado community, I'm a new tado user and now I'm sitting here with a bunch of adapters and none of them seem to fit. I have an oventrop thermostat and I checked the compatibility list here. …
Hello. Due some glitch after electricity failure boiler was not responding to Tado "heat" command for over 23 hours... Temperature in our rooms was dropping down but system did not announce any issues…
Hi I recently moved into a house with Tado installed but no internet bridge. I’ve replaced this and downloaded the app. All says connected yet my heating isn’t coming on. What could I be doing wrong?
I have just had my Tado installed and everything is connected and working fine. However, it just seems to ignore any schedule or instructions that I set on the app. The heating will not turn down or e…
USB cable is very short on the v3+and would like to order a longer cable but I get confused with the various types ie usc c etc Can someone please advise me what I should order
Dear Tado Community, today I relocated the bridge to see if it would connect more efficiently with the receiver as recently the system keeps failing to switch off when it should - which kind of defeat…
I've had a few occasions recently where the TRVs are calling for heat, but they don't get it. I can resolve it by pressing the test button above the 3 wavey lines on the receiver next to the boiler. I…
I installed a v3 starter kit a few days ago. I seem to have a repeat issue where first thing in the morning the thermostat in HomeKit is status “no response” if I go into the Tado app everything is fi…
Hi, I think it was discussed for a long time but search is hard. I am new to Tado, just bought 2 wired thermostat and 8 x Smart TRV which my house had 2 zones for Lower and Upper floor with a wired th…
I’ve had Tado installed for a year now and in the most part I like it. However, it is always overheating rooms. I have UFH in 3 zones and set it to 20°C. It will easily get past 23°C often. I thought …
Have replaced Drayton wireless thermostat and SCR receiver plus Honeywell 699. Hot water works ok but CH doesn’t work. It seems the thermostat/control unit just won’t trigger the boiler. Any thoughts?…
Can I ask if anyone is still having issues with getting flow through SRVs when boiler is called. Have spent a considerable time with support getting valves opened and delaying boiler calls. If you hav…
Dear all, I have a Siemens RDE100.1DHW thermostat. I use this to control my heating system and also have independent control to hot water (DHW). I want to replace it with a tado system. I believe the …
I've run tado successfully here for five years. I don't remember doing anything unusual at the start of summer to switch anything in the system off. Hot water has run as expected over the summer. Toda…
Replaced Drayton wired thermostat and old controller with Tado Wireless V3+ along with 6 Smart Tado radiator valves. The boiler is a Grant 21E Oil boiler. The issue I have is the central heating pump …
Is it possible to see anywhere the temperatures that Tado is requesting from the boiler? I can see people posting them in some threads, but it's not clear to me where to get that information from. Tha…
