-
Would the the following 3 Channel setup work?
Our house is currently using a system boiler, and it has a 3-Channel programmer (Horstmann H37XL) for upstairs heating, downstairs heating and hot water. There are two wired thermostats, one upstairs, and one downstairs. My current thought is removing the programmer and connecting the upstairs heating and hot water to a…
-
Efficiency question
Hello! We've moved into a property that already has a TADO system installed. So have not installed this ourselves. The house is old, cold, lots of windows and poorly insulated. We have all rooms set to 15 degrees as a baseline and raise the temperate when we're at home or using particular rooms. However - just keeping all…
-
Tado Installers
Been looking at a Tado Starter Kit and possibly having a go at installing it myself but the more i look at my heating system the more complicated it looks and the more weary I get especially with how slow the chat facility is (Its a regular boiler with a hot water tank) so I thought about getting a pro in to install it.…
-
Tado Alexa manual control command not working as expected.
Hi, Recently installed Tado and set everything up with Alexa. The documentation says that if I issue the command "Turn off manual control in the (room name)" it should revert to the smart schedule. Instead it simply turns that zone off completely. Is this a bug in the skill? Seems likely that's the case. Doc ref:…
-
New house with Tado installed
Moved into property with Tado - previous owner not helped other than to say download app is easy. Downloaded app. Is Valiant boiler linked to cylinder in cupboard and tank in loft. Equipment I appear to have is Tado thermostat on wall in entrance, tado bridge that I have installed into router in entrance (very short wire…
-
Radiator without TRV
Hey guys; Just installed and have had my Tado running for over 3 weeks now. However I wanted to understand why two of the radiators in the rooms (hallways and master bedroom) where the wired thermostats are installed (that replaced the old wired one) have no Thermostatic Valves. I read somewhere that it’s to balance…
-
Smart radiator valves not heating in a 2 zone S plan
This may be a long post, so apologies in advance. My heating circuit is an S Plan with 2 heating zones (upstairs and downstairs). I have these controlled individually via radio wired smart thermostats. Equipment wise I currently have: - 1x Wireless receiver - 2x Wired smart thermostats - 2x motorised valves, controlled by…
-
How Long Does Being High Last?
The duration of the high from recreational drug use, such as marijuana, depends on various factors. Primarily influenced by the potency of the substance, individual tolerance, and the method of consumption, the effects typically peak within the first 30 minutes to two hours. For most individuals, the peak sensations of…
-
Upgrading from V1 to V3+ and geofencing subscription charges
I currently have the old v1 and I’m thinking of getting the v3+ to compliment my new boiler. I am confused with different stories regarding charges for geofencing. I already have a v1 bridge for a long long time. Will I be able to upgrade to v3+ without a monthly charge and if so, is there a specific way to do this? Thanks…
-
Tado Wireless Receiiver (EU version) + Glow worm Ultracom2 18SXI on EBUS
Hi all, I purchased a Tado setup to replace my old setup for heating, which was a Honeywell ST9400C + 2 "wireless" thermostats in the house. That connected to a Glow worm Ultracom2 18SXI Boiler, which i believe is a combi. in addition to that, a few years ago when i had solar panels installed, the company who installed it…
-
Cannot get hot water control on the app
I can see heating in the app but not hot water. Help please.
-
My heating is scheduled to turn off at 10:00pm but continues running every night
My heating is scheduled to run from 6pm to 10pm (21 degrees) everyday. Iv noticed that each evening after 10pm my heating continues to run. it should only run after this time if the temperature drops below my fall back temp of 17 degrees after 10pm which it doesn’t get that cold! When I check the app after 10pm the…
-
Heat request not being sent to heater
I have an Ariston Clas B Premium Evo Heater, and I bought a wireless Tado (v3+) starter kit for it. I replaced an old relay thermostat with it, and I wired it to use the Ariston bus system (BridgeNet), so the wireless receivers Digital - goes into the Heater's T, Digital + goes into the Heater's B connector. K configured…
-
Tado fitted
Hi got a Tado Wireless V3 kit fitted today basically it was just the wireless receiver that was left to wire up as i had already setup the internet bridge and paired the Thermostat this morning. So a guy came and fitted the wireless receiver in place of my old Drayton programmer today and everything is connected and…
-
Opentherm
Hi all, long time tado user with a new setup question? I've recently had a new boiler fitted (ideal logic max C35) and I'm struggling to get the system working on opentherm with my setup. I have:- Internet bridge V2 Smart thermostat Extension kit 7 x TRV's With the extension wired to the boilers opentherm connections and…
-
Changing Battery on TRV
Hi, Just a heads up when changing a trv battery... Tado instructions say; ------------------------------------------------------------------------------------------------------- "To restart the Smart Radiator Thermostat, remove the batteries from the device and wait 10 seconds before putting them back, then close the…
-
Boiler not responding
Original system Ideal logic system 18 Honeywell ST9400c Honeywell T6360B Fitted Starter kit Wireless smart thermostat V3+ Including programmer for hot water Bridge- wireless temp. Sensor, wireless receiver All paired Wired as per instructions Original stat linked. “S-plan From 3 hw blk. To HW NO From 4 ch grey To CH NO Did…
-
EU Tado Wireless Receiver to Ideal+ Combi C30 Help please
Hi, I'm almost ready to give this a go got the gear trying to replace an old dual channel hive system which was turned into single channel once the combi boiler was installed. I want to take advantage of opentherm and the smart TRVs otherwise it offers nothing more than hive currently does. I've attached photos of inside…
-
Why does my Tado app not have a Heating tile
I have Tado heating, hot water with radiator thermostats
-
Ground Floor too hot
Hi, I have recently acquired a Tado Starter kit (wired) for my house plus smart radiator valves for 3 x bedrooms upstairs. I replaced the old honeywell thermostat and put the tado in the same location: living room - ground floor. It seems that my house has one single zone.- which everytime any bedroom demands heat then the…
-
Why does Internet Bridge "Pairing" status show incorrectly in iOS Tado App?
My Internet Bridge is in pairing mode, confirmed by blinking LED on the bridge, but the iOS app shows "Pairing Inactive" by the joined circles below the bridge details. At the bottom of that iOS page however, it says "Deactivate Pairing" which agrees with the status LED on the bridge itself. Tapping "Deactivate Pairing"…
-
TVR in baby room? health implication of magnetic fields?
Hello. The title says much. I wonder if the magnetic fields required for the Tado TVR to communicate are not bad for the health. General search on internet says that magnetic fields from devicea have impact on brain and nervous system. Is there some rules to follow to limit the impact? Thank you
-
Google nest integration.
I have six rooms with radiators. 4 rooms have tado radiator nobs. My Nest thermostat is in the living room that does not have a todo nob on its radiator. At the moment the heating is set to 17 so the boiler is not on. So setting the other rooms to a different higher temp makes no difference because it’s not getting any hot…
-
Do I need to buy anything to enable opentherm on this boiler?
eli5 please. Just purchased an eu thermostat from the tado website. Have the ideal logic combi c30 boiler. Will the eu thermostat come with everything I need or do I need to buy any additional hardware, Ive attached my wiring on my boiler Thanks in advance
-
Tado TRV periodically open\close
During night time, the boiler is off, so there should be no need to schedule the TRV to turn off heating. For this reason my only schedule starts at 00:00 and ends at 24:00 with my desired temperature. During nigh time, the TRV periodically "works"... you can hear it, you can hear the motor spinning. What is the reason for…
-
Tado App on Android
When I look at the temperature chart in the app Instead of seeing the home symbol for a time period I see the following: (From the App - Heating - select the graph symbol) Any idea what it means ? Thanks
-
Newbie Question Regarding SRT
Currently I have two smart thermostats. One wired that controls the underfloor heating and a wireless one to control the rest of the rads in the house. I have now purchased some Tado SRT. I'm having them installed in a few weeks. My question is, once installed, can I control the heating in individual rooms from my smart…
-
Wired Controllers Status
I'm really enjoying updating our heating to Tado. It is a mixture of TRVs and Underfloor heating. There is something that is really bugging me. The existing underfloor heating controllers that I have are Normally Open, so easy to replace with a wired Tado controller. In the app, there are multiple levels of on. This makes…
-
Factory reset bridge
Hi, I have changed my Tado setup and giving it to a friend however when she is trying to add the bridge to her account it won’t let her. I can’t give her my account details as I have purchased another Tado system. It’s the V3+ wireless bridge and setup I gave to her as I wanted a wired setup (long story) anyway I’ve tried…
-
Remove “OVO” energy account from Tado.
Bit of a long shot but I purchased my Tado thermostat through a major hardware store, I was with British Gas when I set it up. Then I moved to OVO energy and there was an option to link my OVO account to TADO. That was ok for a year or so but now I’ve switched to E.on Next and want to remove the annoying OVO logo and the…