-
Simple fix for the smart TRVs
My smart radiator valves can’t heat a room without setting a large temperature offset due to the sensor being too close to the radiator. This feature doesn’t work very well because when the radiator turns off tado thinks my room temperature plummets, and then instantly turns the radiator back on. This seems to be a very…
-
Buderus Logamax GB142 + RC35 - circulator pump PERMANENTLY ON
I'm a tado user since the very beginning but I never succeeded to turn off the circulation pump of my boiler. My installation: Tado Thermostat wired Buderus Logamax GB142 + RC35 controller (on boiler) 8 thermostatic valves Tado ambience thermostat in some rooms If I override the circulation via the RC35 installed on the…
-
Replacing an UP2 controller
Trying to replace an UP2 controller and switchmaster thermostat. Wired in multiple times but I don’t know where the below wires go on the Tado controller; 1 (blue with brown sleeve) 3 yellow wire 4 red (CH NO?)
-
Vaillant Ecotec Plus 630
Hi, I’m about to upgrade my ancient Potterton boiler to a Vaillant Ecotech Plus 630 system boiler. I’ve been a Tado user for the past 4 years and want to carry on using my Extension Kit and TRVs. The extension kit is a V3 not a V3+. I’ve done a lot of reading and can’t find a definitive answer as to whether I’ll be able to…
-
Genuine Consumer harm
My Home is without heating after installing a Tado system, which was installed by a recommended professional. I cannot even get a response from Tado let alone a fix. I am unable to un install the system - what am i supposed to do? My childrens bedrooms are freezing.
-
Smart TRV’s....what do I need to work with my boiler
Hi. I have purchased the Internet bridge and Smart TRV units and have those hooked up together, but if I wanted to get them direct to work with my combi boiler to control the heating direct what other hardware would I need (as I understand I cant get the Nest unit I currently have to talk direct to Tado)? Can I just fit a…
-
BOILER NO FIRING UP
Hi, I have fitted the wireless v3 control, when the thermostat calls for heat the boiler fan clicks on the fan starts up bur the boiler doesn't fire up, also there is know response at all from a hot water call, I have a Worcester greenstar 18i boiler and a three way vale. Lloyd
-
Installing Tado Wireless Thermostat into a 2-zone heating system
Hi all, I have searched through the forums to see if a previous post exists regarding my set-up, but to no avail. Apologies in advance if I have missed it though! I recently purchased a Tado Smart Thermostat Starter Kit V3 and am looking at the option of self-installing this but I was hoping for some advice on the best way…
-
Do I need the starter kit?
If I buy the Internet Bridge and the Wired Thermostat Addon, is this the same as the Starter Kit? Or will it prevent me from setting it up?
-
Which tado bits are required
I was using tado for about 5 years in a previous home, and will be buying the tado kit for my next property. My previous property was a single-floor apartment with combi boiler, I installed the following tado bits: smart internet bridge, smart thermostat in hallway (wired to a combi boiler which was in the kitchen), smart…
-
Identifying a TRV - can anyone help
Unfortunately there is no manufactures name on the TRVs on my radiators. I have done an image search on Google but results are inconclusive. Anyone help? I attach some pictures. Thanks for any help.
-
Boiler not firing up with OpenTherm
Hi, I have an Ideal Vogue Max Combi 32 boiler. My Tado System is made up of 7 TRV and everything was working fine until I swapped the wireless extension kit for the EU model so that I could use OpenTherm. I believe the wiring is correct, the + and - on the wireless receiver are connected to the OpenTherm terminals on the…
-
Why does Thermostat mode on Smart AC Control not work?
All I want the Smart AC Control to do is manage temperatures within a comfortable range. If it's above the acceptable limit, the AC unit should run in Cool mode until it brings the temperature down. If it's below the acceptable limit, the AC unit should run in Heating mode until it brings the temperature up. Schedule…
-
Tado V3 thermostat has connection issues after changing batteries.
Dear, After changing the batteries of my Tado thermostat (wall model) I experienced some connecting issues. When mounting the cover of the thermostat everything worked fine. but 30 minutes later the connection was lost. What I did next was again opening the cover and close the cover --> and the Tado was connected again.…
-
Thermostat issues
I’ve recently changed the batteries on one of my thermostats as it went offline due to them running out. Worked for 2 days and I have just received another email saying batteries low in the evening and then overnight the thermostat is offline again. Any ideas? The batteries are brand new and another thermostat was changed…
-
V3+ installation with district heating
Hi all Just got myself a v3+ stater kit to replace my fixed honeywell thermostat and Honeywell programmer. Before I replace the programmer, I noticed a couple extra wires in the existing connections so wanted to ask if I can just go ahead and reconnect the existing wires directly into the same connection on the tado…
-
My V3+ setup is not properly supporting zones
Hi all, I have a very simple installation. There are 3 heating zones. My components: 1) V3+ Wireless Smart Thermostat [incl. Programmer with Hot Water Control] for Zone 1 & Water 2) Add-on Wired Thermostat for Zone 2 3) Add-on Wired Thermostat for Zone 3 My problem: The TADO Programmer always turns on the valve for Zone 1…
-
New Tado thermostat and Prime TRVs - radiators not on
Hi. We've just had a Tado smart thermostat installed and, at the same time, changed all the radiator TRVs to Prime TRVs (manually operated). If the Tado thermostat reaches temperature but eg one or two rooms are below the temperature being called for by the TRV i.e. a rad is set to '5' on the TRV, does the Tado 'win' and…
-
Turned one radiator on, another radiator turned on as well
Hi, Please can you help. I have a wired Tado thermostat. The radiator which is in the living room where the thermostat is situated doesn’t have a Tado valve (I thought I read that there shouldn’t be a Tado valve on the radiator where the thermostat is located, but I could be wrong). Anyway, when I turned the bedroom Tado…
-
Why is away mode not overriding manual settings?
As mentioned above - if im the last user exiting home, away mode should not only turn off the scheduled temperatures, but also override the manual settings. For example my schedule stopped at 23, but i changed it manually 'till 23.30. At midnight I've leave with away mode turned on. It didn't affect the manual override.…
-
Modulating controls Compatibility - Glow Worm Ultimate 24h
I have a Glow-Worm 24h System boiler (Y-Plan, Monozoned). I use my Tado via the original extension kit which has the Low Voltage Contacts for use with eBUS, however its currently wired up using old-school relay mode to control both the HW and the CH. From what I can tell in order to use the modulating controls via eBUS and…
-
Home temperature reading and actual temperature
Can anyone help. My Tado thermostat is set to heat at 24C. The temperature at the radiator is 19.1. The room temperature measured by a digital thermometer is 18.3 . Temperature offset is -0.8. Despite being set at 24C the room temperature will not go above 18.7
-
Why does my central heating not start?
Hi. My boiler was already using Tado system when I moved into our new house, but it looks like the boiler doesn't get commands from Tado. Whatever settings I do, they don't change anything on the boiler. Thank you
-
Low heat demand not heating radiators
I have Tado operating in modulating mode on my WB boiler. If a room calls for low heat demand (1 wave) often the boiler will fire and pump at a low heat but no actual heat will get to radiator. This doesn't happen with 2 or 3 waves, just 1. Often the boiler will fire and pump for hours and achieve no heating of the room.…
-
More compatible heat pumps
At…
-
PID regelaar voor de sturing van de thermostaat knoppen
Vanuit de klanten service kreeg ik de vraag of ik mijn vraag hier wilde stellen. Graag zou ik zelf de PID-regeling van de thermostaat knoppen zelf kunnen instellen. Dit omdat niet alle knoppen bij mij een radiator bedienen.
-
TADO - hot water not hot enough
Hi All, I hope you will be able to help me with this. I have installed the tado system (bridge, receiver, thermostat, valves). The heating is working ok and there is a hot water but the problem is the water is not hot enough. I am heating the water 2 x per day 30 min as I have cylinder storage. Before I was using the…
-
One Tado valve
Hi folks, I tried to turn my heating on last evening with just one Tado valve turned on, the rest off, basically to keep my granddaughters bedroom warm. I noticed during the evening they the room was cooling. Strange I thought as the app showed it on, temperature set to 23 (but showing 20 and reducing) radiator wouldn’t…
-
Vaillant ecotec plus 837 & Honeywell cm927
Hi Hope someone can help. I have a vaillant ecotec plus 837 with a Honeywell cm927 wireless thermostat. I want to replace the cm927 with Tado wireless thermostat. According to tech support that's possible and fairly easy to do, would anyone be able to give me rough instructions before I purchase the kit or is it best to…
-
New idea: respond to valid user suggestions?
Hey tado development team, being an owner of a software agency myself, it's a huge red flag to me when I see rather trivial user requests and improvements just sitting there for five years (!!!) without an official response. Some guy named "Frank" answered who seemed like a tado rep, but his account is deleted now.…