For district / city heating the bill and meter readings are in GJ. It is very annoying to have to manually convert the units. Should be an easy fix: 1GJ is 277,8 kWh or 31,6 - 32,68 m3 gas.
When no heat is requested, the pressure in the system can be so low, that the radiator valve pin does not spring out fully. This can result in an E4 error, or invalid calibration. This can be manually…
Do I need a subscription for geofencing to automatically work when both our phones are away from home? It shows both our phones are outside the perimeter but the temperature indoors stays set to home
Hi We have a tado V3+ that it not working, about twice a week, although the app shows the heating should be on (always in a morning) it's not coming on, it only works when I select the boost option. A…
Hi all, Tado user since 2017 where have the following setup... EPH 3x channel/zone programmable control panel (2x CH & 1x HW) with a wired thermostat for downstairs and a wired thermostat for upstarts…
The included 30 cm power wire and ethernet cable contradict the advice that optimal positioning of the bridge should be vertical and not directly behind the router. It is very hard to get the bridge i…
Hi I have a few thermostats in my house that I am planning to replace with Tado Wireless. 1) What is the max distance between Smarthub and the thermostats? 2) I will have 4 thermostats (wired) connect…
Hi Everyone, So we have a new build property with an Ideal boiler which is capable of Opentherm and modulation. I purchased the Wired version of Tado as I read that it was capable of achieving this vi…
Hi have just had new wireless v3+ installed, the bridge and controller are online but the wireless thermostat is off line, have tried pairing loads off times have reset, have moved the bridge but can’…
App says to contact support so going down this route. Any help on the wiring for swapping these over? This controls the hot water and there are two wired thermostats for 2 zones that I need to replace
So got a new Tado system installed yesterday. Not impressed. 1x wall mounted smart thermostat (upstairs zone) - replaced old danfoss thermostat 1x wall mounted wireless temperature sensor (downstairs …
I bought and installed Tado Starter Kit with Wireless Smart Thermostat to replace Danfoss TPOne-M controller for main central heating and hot water. That works fine but I also bought and installed a T…
A command to restore the schedule both by room or whole system is vital. I keep forgetting to manually restore at night and wake up to cold or too hot rooms. This command could be used as part of a 'g…
Issue The Tado was causing the boiler to enter Anti-Cycling mode. After speaking to Tado tech support, they have changed the Tado relay “to turn on once there is a heat request, and turn off once this…
I have underfloor heating downstairs and radiators upstairs. I also have a hot water storage tank upstairs. The timings associated with the firing of the boiler are managed by a three channel controll…
Tado speaks about being environmentally friendly but my radiator thermostat broke. The resolution is to share a receipt and they ship me a new one (across multiple countries) and then I return mine (a…
Hello, we need your help to see if/how I can control an underfloor heating with our current Tado system. Situation We have a conventional boiler and a hot water tank. We have a wireless receive/extens…
I've searched for this, but no one seems to have the same problem. I have a schedule set to turn my AC to heat every morning, and turn off at 7:30. However, most mornings the tado unit doesn't send th…
Hi All. I have an Ideal Logic+ 35 combo boiler and I've just installed the Wired Smart Thermostat starter kit v3+. I specifically chose this as both the boiler and the smart thermostat both support Op…
Hi Everyone, So thanks to you lovely people, I managed to realised the Wired Thermostat was not infact suitable for my use case and therefore ended up purchasing the EU version to allow Opentherm and …
I noticed that tado is not good at keeping a stable room temperature. Instead of turning the heating on in advance while temperature is dropping close the level, it turns on when it’s just below. But …
I have four rooms controlled by tado. At night time when only one or two radiators in bedrooms are potentially heating at a time the radiators are too noisy(loud water flowing noise)- I assume as all …
Hi, we have the baxi 830 combi using opentherm with tado and Drayton TRV's. If radiators are balanced they all heat up properly and radiators are quiet until the boiler modulates down as it starts to …
Hi all, Recently we have had some issues with our Ideal Logic Boiler whistling / whirring as it fires up. It doesn't happen every time, but it's noticeable when it does, and it's started happening in …
It’s usually lot of waste of heating when heating is on level 3. Tado is not able at effectively run preheating economically. Its ability to learn this effectively gets complicated as the many things …
Hi I’m looking to install a Tado V3 to replace my existing boiler controls. It’s currently using an apt timer for control and it’s a bit dated. It’s a Firebird Envirogreen 20-26kwh Boilerhouse model. …
