-
I want hot water to turn on automatically when heating is turned on
Please forgive me if this is already a well established method, but I am having trouble finding a solution. Could anyone advise me as to whether it's possible to have the heating control automatically turn on the hot water. We have set up our programme to have both the hot water and heating working in sync, but with frost…
-
“Saved Schedules” Idea
Hello, I have seen some posts about shift workers. To echo these. The way of editing schedules is very fiddly and time consuming, especially when you have a different shift pattern each week. It would be more beneficial to have “saved bank” of specific days and specific weeks you work, and you can quickly copy them into…
-
replacing existing wireless smart thermostat
Several times now my wireless smart thermostat has lost pairing with the bridge. (it's out of warranty). So in the morning we have no heating or hot water. It took me several attempts to get it to start working again this last time. Can I simply replace the existing smart thermostat with a new one?
-
Suddenly app not showing correct settings
All has been fine for a month but now in my app it says the temp is set to 13c for my rooms whereas if I open each room I have set the temp to 16 for each schedule . I see no way in this discussion to add screenshots - is this because I am in my iphone or can I really not add photos to show the issue?
-
Internet down and then?
Hi When I changed my boiler and the water tank. I told the installer that I wanted a controller that I can control via my phone but also directly in case the internet is down. I now got Tado installed and the only thing I can do without using the app on the phone is using the controller to change the main temperature, turn…
-
Hot water boost via app
There used to be functionality using the app whereby you could boost the hot water for a limited period of time, say 1/2 hr then it would return to schedule. As it now works you can only override the schedule and turn the hot water on. If you then forget to turn it off it will run 24/7, not good at all..
-
Add hot water boost - instead of manual control under hot water settings
In order to boost the hot water for a time period (eg 1 hour) you have to go into Rooms & devices, settings, hot water and then finally access the manual control. It would be a lot easier and more user-friendly and intuitive if there was a simple boost button under Hot water icon. In case anyone is following all the…
-
Chaffoteaux inoa green 24 EU. Bus protocol doesn’t work with extension kit.
Hello, I’ve got a combi boiler Chaffoteaux inoa green 24. I’ve installed extension kit and wireless smart thermostat like in installation instruction by bus protocol. But my boiler doesn’t work now on bus protocol with tado Before i’ve got an on/off salus thermostat. I think The problem Is that i need to make some changes…
-
Moving House... add an extension kit to existing install?
Hi all, I am moving house and taking my Tado equipment. I currently have a Combi and I am moving into a house with a hot water tank and non-zonal heating. The controls are traditional 90s Honeywell programmer and wired thermostat. I want to use my existing Tado and I assume I will need an extension kit to have hot water…
-
iPhone/Siri Shortcuts Support
TADO application doesn't appear in Siri/iPhone shortcuts. This application is very powerfull and, though complicated to use, can do much more than IFTTT in the Apple world. Tado must support Siri shortcuts. Homekit is obviously supported and a few (very limited) number of things can be done that way. Please support me.
-
Wiring up a Ideal Vogue C32 GEN2 with V3 starter kit.
Hello! After reading the forums, it seems like this should be pretty easy but the instructions / boiler don't make this easy for my simple head - clearly! I'm trying to upgrade from a Ideal touch wireless thermostat. Here are some pictures of what I can see. @johnnyp78 - any advice? You seem to be a helpful chap!
-
Changing Thermostat Batteries
Hello, after I changed the batteries to my radio thermostats, the thermostat seems not to work anymore. If I pushed the button I get no lights or messages o temperature reading. The app keep saying that the thermostat is connected and the batteries are low. If I try to get the greeting message to visualize in the…
-
Missing “Jumper” extension kit
Hello! Does anybody know how I can option the orange “jumper” for my extension kit? I have just moved into my new house with an existing Tado system and the I realised the boiler was constantly firing, even when the radiators were off. After some back and forth with support, it seems I need an orange jumper which is…
-
Ability to use Wireless
Tado needs the ability to use multiple wireless temperature thermostats to control different rooms independently.
-
My boiler is nit triggered by Tado thermostat
Today I installed the Tado wire thermostat. It doesn’t triger my boiler
-
Heating status for On/Off mode
I would prefer to see the heating status as a simple on/off symbol rather than the three waves. I have a heating source that does not support opentherm and thereby only works in on/off mode. Why I would need this: This would be useful to really check if my heatpump is working properly: I currently do not always know for…
-
Radiators + Water-based underfloor heating
Hi, I have 3 floors at home. Floor 1: 1 Wired Smart Thermostat + 2 Smart Radiator Thermostats Floor 2: 2 Smart Radiator Thermostats Floor 3: Smart Thermostat wired to the pump controlling the Water-based underfloor heating. I used to connect all the Smart Radiator Thermostats to the Wired Smart Thermostat in Floor 1 (Zone…
-
Increase Zone Controller Max Rooms
I ran into the limit of 10 rooms on one Zone Controller and I need it set to 12 rooms. I am sure this has also affected other Tado users retrofitting a complete house.
-
Wired up as required but have no central heating. Grant vortex pro 26e.wiring diagram in manual is n
Wiring in manual is numbered
-
Controller setting wrong
I'm not getting any hot water, after a year or two of having everything working OK. We have Yplan gravity system with hot water cylinder. We changed the mechanical valve head but still no joy. Tested the controller and it shows as yellow, combi. When I change it to green for Yplan it flashes and settles on green but still…
-
Wired thermostat v3 and radiator thermostats in one room not supported?
I have installed a wired smart thermostat and radiator thermostats on the radiators in the main room. I have radiator thermostats in other rooms as well as I want to program with a different temperature/schedule I noticed that the radiators in the main room are closed off when the temperature is achieved, as expected. But…
-
How customisable are tado’s manual controls?
Hello all. I’m considering setting up my whole house with tado - smart radiator valves included. I’m yet to find a clear answer on something and wonder if someone can help. Is it possible to control the whole system manually with one ‘command’? Whether that’s a button in the app or an Alexa voice command. Probably easiest…
-
Worcester Bosh 24/28i Greenstar with Comfort RF 1 wireless thermostat
I've bought a Tado from Ovo, but now realise my control unit is listed as 'not compatible'. Is there any way to fix this? The unit is a Worce.ster Bosh 24/28i Greenstar with Comfort RF 1 wireless thermostat. My plumber has tried installing it, but we can't get the heating to come on. Why is this so hard, there only seem to…
-
Postponed buying 8 Tado thermostats, looking for other solution!
Postponed my idea to install 8 tado thermostats, because it appears that, nevertheless many people ask for this integration, still nothing happens. If it comes to brands that cannot be integrated with Smartthings, there are a lot more cheaper ones on the market I figured...
-
Trying to modulate a Worcester greenstar 440cdi ErP
Hi, I have recently had a new boiler fitted and for various reasons it had be a greenstar 440. As I understand it Tado is able to modulate Worcester boilers through HT-BUS / EMS-BUS. The problem I’ve got is that the person who fitted my boiler has connected in Relay mode as that’s how the previous one was done. I cannot…
-
Thermostat Not Following Programming Schedule
Last night the thermostat called for heating, switching on the boiler and heating circuit. It did this although the App and Smart Schedule had the Thermostat programmed to OFF. The App showed the thermostat status as OFF. Even so the thermostat ignored the programming and called for heating. Any ideas why?
-
Tado HW function not working!
Got it working now by reconnecting the devices and re-installing the app.
-
Smart AC Installation
I have bought a Smart AC control but the installation lacks any useful information. How can I connect it to Wifi? What is the HomeKit? Ok i figured it out I have to download 'Home' application which is never mentioned at anywhere at Tado site / installation process. Do I need 'Home' to be installed on my phone to be able…
-
Air Comfort suggestions
Hello, We're supposed to make energy savings with Tadoº, but it's quite inappropriate to get a suggestion to turn the heating on when a room is just below 20ºC. The World Health Organisation recommends a room temperature of around 18°C in Winter, and The Energy Saving Trust advises setting the thermostat to around 18-21°C,…
-
Measuring device
Hi All, Just a very quick question. Does setting a measuring device in a group disable other devices within that same group from calling for heat? I can't see a definitive answer in the community and have seen previous discussions mention that this function has to be set up by tado support, so just wanted clarification.…