-
Extension Kit as a Hot Water Programmer - Help!
Hello, I am having trouble with adding a wireless extension kit to control my hot water programmer. Quick summary of my existing setup: I have had a Tado setup in my house (a 4-year-old new build) for about 4 months. There 2 thermostats downstairs which connect to UFH. Upstairs there is another thermostat setup as a zone…
-
Is it possible to see room graphs via Tado for nearly 2 years ago?
My graphs only go back 12 months. Are they stored eg by Tado anywhere? Thanks
-
Signal Keeps Dropping - Internet Bridge light flashing
My tado system has been workng well since installation until recently - The internet bridge keeps falling off and goes "offline" It seems to drop on and off at certain times of the day, and then at other times works well I have located the bridge right at the centre of the house, reasonably near to the boiler and centre to…
-
Boiler switches from Constant on to Automatic then does not respond to Tado
I have a Worcester Bosch Greenstar HE 35 connected to wireless Tado. I set the boiler to ‘Constant on’. Everything works fine. However, for some reason the boiler switches itself from Constant on to Automatic, then it does not respond to the Tado until manually switched back to Constant on. Can anyone help/advise how to…
-
Three zone central heating system
I have a three zone central heating system with a programmable thermostat on each floor controlling a 2 port motorized valve. Can I replace the thermostats with wired tado smart stats. I do not need smart HW control
-
Adding wired thermostat to hot water wireless starter kit
Hi, I've replaced my honeywell ST699 with the wireless starter kit for my s-plan HW and CH system and all is working as expected. However, i've currently bridged the DT90E wired thermostat wiring and mounted the wireless thermostat here however, is there a wiring diagram for how the wired thermostat should be added to this…
-
Boiler constantly ON
Guys , I have the following setup . Smart Thermo linked to an extension kit in the Hot Press which controls a valve to control hot water and call for heat , connected to Internet bridge . On the installer app all show as connected and up to date , the problem is that the boiler (Ideal Logik 24 ) is constantly ON . I've…
-
Wireless temperature sensor problem
I have a room controlled by the wireless temperature sensor . It controls the smart radiator valve . The sensor doesn’t get the temperature up to the target temp before switching off the boiler .I have to keep increasing the target temp to get it to switch the heating on again . Any ideas welcome
-
Replace danfoss with tado
Hi, I would like to replace my Danfoss (not sure if TP4000 or TP5000) with a tado wired thermostat. There are just 2 wires connected to the Danfoss, one connected to COM and one to ON. I have a combi boiler (Heatrae Sadia Electromax) and the thermostat controls just the heating, not the hot water Would the tado thermostat…
-
Wrong room heating up
We have inherited our tado system with a house purchase and have smart thermostats on every radiator in the house. We have had a few troubles with it. Over the summer I programmed all of the rooms to OFF FROST PROTECT but on 2 random occasions that I am aware of all the heating came on in the house even though the app said…
-
Replacing old controller and thermostat with wireless Tado. No access to wiring centre.
Hi, I am looking to replace my old Honeywell ST6400C controller and Honeywell wired thermostat with a Tado V3+wireless thermostat starter kit. I have a Worcester Greenstar 24i system boiler. Unfortunately due to thoughtless installation, the wiring centre is inaccessible without removing the boiler. I was wondering if I…
-
losing Faith with Tado.
So we've had a wireless tado system installed by a qualified heating engineer but right from the start we've had issues. There is one wireless smart thermostat in the hall and one in the lounge, with two Tado SRV's, as suggested by Tado. Then there are two more SRV's dotted around the house and the rest are just TRV's with…
-
One of the radiator became very hot but thermostat is turned off
The radiator in dining room became very hot since 2pm today, but the thermostat configured OFF the whole day! Seems whenever the boiler is turned on, the radiator in dining room would be warmed up no matter the thermostat is configured on or off. Could anyone advise what I should check or do? Thanks. Alexander Lai
-
I want hot water to turn on automatically when heating is turned on
Please forgive me if this is already a well established method, but I am having trouble finding a solution. Could anyone advise me as to whether it's possible to have the heating control automatically turn on the hot water. We have set up our programme to have both the hot water and heating working in sync, but with frost…
-
replacing existing wireless smart thermostat
Several times now my wireless smart thermostat has lost pairing with the bridge. (it's out of warranty). So in the morning we have no heating or hot water. It took me several attempts to get it to start working again this last time. Can I simply replace the existing smart thermostat with a new one?
-
Suddenly app not showing correct settings
All has been fine for a month but now in my app it says the temp is set to 13c for my rooms whereas if I open each room I have set the temp to 16 for each schedule . I see no way in this discussion to add screenshots - is this because I am in my iphone or can I really not add photos to show the issue?
-
Internet down and then?
Hi When I changed my boiler and the water tank. I told the installer that I wanted a controller that I can control via my phone but also directly in case the internet is down. I now got Tado installed and the only thing I can do without using the app on the phone is using the controller to change the main temperature, turn…
-
Chaffoteaux inoa green 24 EU. Bus protocol doesn’t work with extension kit.
Hello, I’ve got a combi boiler Chaffoteaux inoa green 24. I’ve installed extension kit and wireless smart thermostat like in installation instruction by bus protocol. But my boiler doesn’t work now on bus protocol with tado Before i’ve got an on/off salus thermostat. I think The problem Is that i need to make some changes…
-
Moving House... add an extension kit to existing install?
Hi all, I am moving house and taking my Tado equipment. I currently have a Combi and I am moving into a house with a hot water tank and non-zonal heating. The controls are traditional 90s Honeywell programmer and wired thermostat. I want to use my existing Tado and I assume I will need an extension kit to have hot water…
-
Wiring up a Ideal Vogue C32 GEN2 with V3 starter kit.
Hello! After reading the forums, it seems like this should be pretty easy but the instructions / boiler don't make this easy for my simple head - clearly! I'm trying to upgrade from a Ideal touch wireless thermostat. Here are some pictures of what I can see. @johnnyp78 - any advice? You seem to be a helpful chap!
-
Changing Thermostat Batteries
Hello, after I changed the batteries to my radio thermostats, the thermostat seems not to work anymore. If I pushed the button I get no lights or messages o temperature reading. The app keep saying that the thermostat is connected and the batteries are low. If I try to get the greeting message to visualize in the…
-
Missing “Jumper” extension kit
Hello! Does anybody know how I can option the orange “jumper” for my extension kit? I have just moved into my new house with an existing Tado system and the I realised the boiler was constantly firing, even when the radiators were off. After some back and forth with support, it seems I need an orange jumper which is…
-
My boiler is nit triggered by Tado thermostat
Today I installed the Tado wire thermostat. It doesn’t triger my boiler
-
Radiators + Water-based underfloor heating
Hi, I have 3 floors at home. Floor 1: 1 Wired Smart Thermostat + 2 Smart Radiator Thermostats Floor 2: 2 Smart Radiator Thermostats Floor 3: Smart Thermostat wired to the pump controlling the Water-based underfloor heating. I used to connect all the Smart Radiator Thermostats to the Wired Smart Thermostat in Floor 1 (Zone…
-
Wired up as required but have no central heating. Grant vortex pro 26e.wiring diagram in manual is n
Wiring in manual is numbered
-
Controller setting wrong
I'm not getting any hot water, after a year or two of having everything working OK. We have Yplan gravity system with hot water cylinder. We changed the mechanical valve head but still no joy. Tested the controller and it shows as yellow, combi. When I change it to green for Yplan it flashes and settles on green but still…
-
Wired thermostat v3 and radiator thermostats in one room not supported?
I have installed a wired smart thermostat and radiator thermostats on the radiators in the main room. I have radiator thermostats in other rooms as well as I want to program with a different temperature/schedule I noticed that the radiators in the main room are closed off when the temperature is achieved, as expected. But…
-
How customisable are tado’s manual controls?
Hello all. I’m considering setting up my whole house with tado - smart radiator valves included. I’m yet to find a clear answer on something and wonder if someone can help. Is it possible to control the whole system manually with one ‘command’? Whether that’s a button in the app or an Alexa voice command. Probably easiest…
-
Worcester Bosh 24/28i Greenstar with Comfort RF 1 wireless thermostat
I've bought a Tado from Ovo, but now realise my control unit is listed as 'not compatible'. Is there any way to fix this? The unit is a Worce.ster Bosh 24/28i Greenstar with Comfort RF 1 wireless thermostat. My plumber has tried installing it, but we can't get the heating to come on. Why is this so hard, there only seem to…
-
Trying to modulate a Worcester greenstar 440cdi ErP
Hi, I have recently had a new boiler fitted and for various reasons it had be a greenstar 440. As I understand it Tado is able to modulate Worcester boilers through HT-BUS / EMS-BUS. The problem I’ve got is that the person who fitted my boiler has connected in Relay mode as that’s how the previous one was done. I cannot…