-
Valve pin position indicator
My Bosch system which I got rid of in favor of Tado included in the app a place where you could see the position of the valve pin. This was useful to determine if TRV was fully opening or closing the valve pin and other temperature issues. I think this would be useful on the Tado system as well
-
Antifreeze & déactivation possibilty
Hello, Support told me that it s not possible to deactivate or change the antofreeze temperature. The minimum temperature when you set to off is 5°C. I would like to be abble to set the antifreeze temperature at a temperature below 5°C (as set by default). And also to be abble to deactivate completely a radiator head. This…
-
dealing better with low battery: add a new battery state "yellow"
i have noticed a couple times that i get a tado e-mail that a device needs new batteries but when i look at the app it will show a green battery icon and "good" the cause is, i think: during a cold night the batteries have lower capacity and the e-mail get sent. the app will also show a red icon when looked at right after…
-
Relative units in Energy IQ setup
In residential buildings there are still some individual radiator meters. In the Energy IQ setup one can only give kWh or m3 as unit but this is only available on a building level. Can something be done to use individual meter readings from Techem meters for example?
-
UK Customer Service Telephone Number
Currently no UK customer service telephone number is available. This is not good for Elderly people who are less technically endowed then other generations and when they have a fault just want to speak to someone to get the fault rectified especially in the Middle of a UK winter. It causes allot of anxiety. Given the…
-
Settings after signal loss and auto-reconnect
Regarding the wireless receiver of the central heating, it is undesirable for it to remain on when there is no signal. I have returned several times to a home with tropical temperatures after the signal was lossed for unknown reason (so far) and the heater remains (last setting before disconnection). Can't this be set to…
-
Data export
Please allow download of chart data for each room. This would be most useful as a CSV file. Data available should include date/time, actual room temp, demand temp (what the heating has been set to), humidity, open window detection, etc. I would like to be able to analyse my own data, and be able to make easier comparisons…
-
Switching between Zone Controller and No Zone Controller/ Universal Switch
Please could you incorporate a universal switch for Zone Controller, so that the user could switch all his TRVs to "No zone controller" and back to the specific Zone Controller with a single toggle button? Currently, it's really annoying having to go to Settings -- Rooms & Devices -- The name of a TRV -- scroll to the very…
-
Open mode
I suggest to incorporate to smart radiator thermostat the possibility of allowing the valve to remain open, even if it exceeds 25 degrees
-
Matter…Thread
a few month later nothing new ? I don’t want to buy dead products…
-
Wireless Internet Bridge
This is a super simple idea, and franky it surprises me you haven't done this yet (or have you?), but wouldn't it make sense to have an alternative do the Internet bridge with a wireless antena? I have my home fairly well covered with a mesh wireless connection, but the fact that you need to have all radiators connected…
-
Monitoraggio finestre aperte
In Tado non esiste un report relativo al monitoraggio delle finestre aperte durante la giornata. Propongo, se possibile e non troppo oneroso, di inserire questa nuova funzionalità che ci dica: - tutte le stanze in cui si è verificato il rilevamento con gli orari - quante volte in quella stanza si è verificato - le…
-
Show end time while editing the duration of a heating override in the tado (web)app
When temporarily overriding the heating schema (e.g. I temporarily want to heat up a specific room), I can choose for how much time I want this override. However, I typically want to directly see at what time this override will stop, not only how long it takes. So basically, when setting the duration of the override, it…
-
Battery Warning TRV
Can you please provide a warning when battery low. At present a warning is given and TRV has already failed. Please give a warning earlier before the trv fails
-
thermostat mode
Hello, the choice to eliminate the possibility of setting the operating mode on the thermostat (legacy mode) to turn off the air conditioner "manually" is wrong; it was a very useful option.
-
Can Geofencing button be put higher in the home screen
I use my geofencing button very often in order to switch manually from "home" to "away". I would like to have this button on top. After all, it over-rules all other buttons Can this button be added to the function button "Reorder Rooms". This way, I can put the button where I want it Thanks
-
add LPG to Fuel type
would i be possible to add LPG to Heating Type with the calculations to work with graphed data to reflect price and KWH for unmetered connections
-
Default for adjusting a TRV should be “until next change” or at least set as default
I quite often increase the heating in the front room using the TRV. That seems to set the temperature “until you resume the schedule” whereas if you use the app the default is “until next change”. This has resulted in me leaving the heating set on 20oC overnight a few times. Is there a way to change the default setting? If…
-
Temperature Display
Hi When you blink the display from the app can it display the current temperature rather than a pointless message. Regards John
-
Global boiler override schedule
My system gets turned on a lot as different rooms heat up at different rates. I’d like to have a global boiler override schedule so I can ensure it’s always off at certain times (including heating and hot water) rather than having to try and set weird on/off blocks for every room throughout the night/day to try and save…
-
Graph showing global boiler activity
I don’t think this exists, or I cannot find it. I’d love to be able to see the pattern of when my boiler is active globally rather than when each room is calling for heat.
-
Open or close valve without controlling heating system
It would be nice if we could control the valve full open or fully closed without start/stop heating system. Example, i need a radiator always opened because of the pressure system and dont want it to control the heating system, just let the current water flow in.
-
eliminazione modalità operativa su Termostato
Salve volevo farvi ragionare sulla scelta di eliminare la possibilità di impostare la modalità operativa su Termostato con il controllo clima In pratica adesso questa funzione non è più utilizzata perchè ritenuta obsoleta. Sono in disaccordo. Attualmente con l'ultimo aggiornamento avete impostato che il controllo clima da…
-
Away mode schedule
It would be great if Tado would support an away mode schedule: a schedule that only operates when away mode is triggered, instead of the current single away mode temperature. My use case: due to dynamic energy pricing it is wise to start heating around noon, even if I'm away. But if I'm home in the morning than heating…
-
Show Actual Status of Wired Thermostat Controller
Hello Team, Currently Wired Thermostat shows heating on only when it's manually Switched ON to a heating setpoint or scheduled ON. It would be good to see when the controller switched ON the Heating device based on the requirements of Room TRV Controllers.
-
Away mode schedules for hot water
Away mode for hot water is simply on or off. Is it possible to have on or off or a schedule? As is case with heating, when I go away in winter months, I would want some heat in the water system as well as within the home to ensure against freezing pipes and condensation build up in rooms and mould.
-
Different setting based on who is at home
Firstly, this function may have been mentioned before. I couldn't find it though. There are 4 of us in the house, me my wife and the two children. All radiators in all rooms have the Tado radiator controls. All 4 of us have access to the app and use location tracking. When just the two of us (my wife and me) are at home, I…
-
Catalan language
As a Tado's thermostat owner and Catalan speaker, I want purpose you the new idea to add Catalan language in your app. Catalan language is known for about 10 million people (from Spain, France and Italy) so it would be great for Catalan speakers enjoy Tado's apps in their own language as other European people do. Thank you.
-
Average temperature of multiple thermostats in same room
In a large room with multiple radiators/thermostats, it would be good to have the option of using the average/weighted temperature instead of having to choose one device.
-
Option to select between load compensation or weather compensation
Hi Could you add an option to select between using load compensation or weather compensation using internet weather data, this would let you try both methods to see what works best for your particular house. On all digital buses craig