-
Allow swiping to access next room
Once you selected a room you should be able to just swipe to the next room but have to come out of the room to go back to the home screen and then select the next room; this is rather cumbersome and was much easier in the pre-v3+ app
-
Multi Home Support
I would like to use tado in my main house and in my vacation home. Currently this is only possible by using one account through the app and the other account using the web-app. I would like to have both available in the same account.
-
Decrease burner power before lowering target flow temperature
Hi, I have a bosch condens 2500 boiler, connected with nefit opentherm-ems converter. Using this setup with tado x wireless receiver (+trvs, wireless thermostats), via opentherm control. As far as I see, this setup works well, changing the target flow temeprature and setting the burner power to minimum value happens, so…
-
Boiler Overun
When all heating demand is stopped our boiler goes into overrun and dissipates it heat into the garage (where it is not required). It would be good if when the heating is not called for boiler heat demand signal is stopped but the radiator valves would stay open for a adjustable time to use the stored boiler heat in…
-
Give users access to the advanced configuration parameters
As most of us here will be aware, Tado has several advanced controls and configuration options that support are able to use to configure your devices when you contact them (cycle periods, minimum on/off times etc). Sadly these advanced options are hidden from users and the only way to access them is through support which…
-
thermostat mode
Hello, the choice to eliminate the possibility of setting the operating mode on the thermostat (legacy mode) to turn off the air conditioner "manually" is wrong; it was a very useful option.
-
my.tado.com : support for 2FA
Hi. There is a ETA for support 2FA for the accesso to my.tado.com ? Best regards
-
Profiles (again)
How much work will there be to enable us to create differnt profiles in the app? I know its been asked before but users seem to have an answer by adjusting the existing home profiles. I DONT WANT TO DO THIS. I want to press a button when for example we have guests staying or if we have a snow day or i'm working from home…
-
Funzioni in app
1 ) Sarebbe utile integrare in app la possibilità di variare manualmente la temperatura di mandata dell'acqua. 2) Quando alla caldaia è collegata una sonda esterna utilizzare la temperatura letta da essa ( sicuramente più precisa ) per regolare la temperatura interna perchè i dati del meteo sono troppo generici e succede,…
-
Better support for Underfloor Heating
Hi, I would like to request better software support for underfloor heating systems in the Wired Thermostats when using relay mode. The modulation used by the Tado Wired Thermostates is not beneficial to my system because it tries to turn the UFH on and off repeatably when NOT calling for "full heat" (i.e. when calling for…
-
Ability to rename device
When batteries are running low I get an email informing me that a particular device in a specific room has an issue. In some rooms I have 4 radiators. I then have to go round ‘blinking’ the stat multiple and watching all the stats in the room to find which one it is. it would be great to be able to rename or give a…
-
Enable eBUS support for Tado X Wireless receiver
The V3+ supports both eBUS and Opentherm however the newer product series X does not support eBUS. Please enable also eBUS support for the X series. I imagine since you have the code for V3+ in the firmware it could be refactored over for the X and with a firmware update it could work.
-
Reduce the comfort temperature range to 18-21°c
In the uk a room set for the comfort range of over 20°c can far exceed a comfortable temperature. I would suggest reducing this so my app doesn't think my house is cold all the time
-
[Energy IQ] Allow for new meter and continue entering meter readings
When replacing a meter, it becomes hard to continue entering meter readings as one has to add the last old meter reading to the new meter readings (and sometimes even subtract the first new meter reading from that number too). Under Energy IQ, provide a meter reset button, with for the date of changeover: ++ the first new…
-
Data export
Please allow download of chart data for each room. This would be most useful as a CSV file. Data available should include date/time, actual room temp, demand temp (what the heating has been set to), humidity, open window detection, etc. I would like to be able to analyse my own data, and be able to make easier comparisons…
-
Ability to schedule "one time" events
Currently you can define a schedule but sometimes I have the need to just schedule a one off session. For example, Friday I will be home earlier than usual so I want to have the temperature be 20 degrees at 13:00 with the end-time being the "next" change. Its nice if this is possible because Tado will then pre-heat…
-
Support one decimal place (0.1) for radiator valve temperatures in the Tado app
These devices appear to report their temperature at 1 decimal place of accuracy (I see it via the API in my Home Assistant integration) yet the Tado app only shows their temperature as integers. Can you please change this? I recognise this might be difficult on the device display itself but not in the app. I'd also like to…
-
Wireless Receiver status
I'd like to see some status on Wireless Receiver, which thermostat is activating, a diagram would be also good, I'd like to see what is the running time of my heater in a day, could be also an indication of which room/device started/use it. Also, in Home Assistant the status of the thermostat is "heat", never goes "off",…
-
Better Boost Options
I was pleased to see the boast function for the system but very disappointed that you can't select the temp (25 is way to high for my house), or select to just boost one room/trv. I find that I often want to boost a room for just 10mins, and only being able to boost for 30mins at 25 is wasteful and unnecessary. I see that…
-
Better explanation with regards to termination of the old thermostat wiring.
I have recently installed the V3+ system and everything went well with regards the installation. I could see all the devices on the app and all the test procedures passed on the Wireless Receiver. However, the heating and hot water would not work. I was convinced I had done everything correctly and was struggling to…
-
Guest mode
There could be an option for guest mode, which would use a different schedule.
-
Exclude rooms from the energy report
Is it possible to exclude the heating of certain rooms from the energy report? Because I have a room in my home where the heating is centralised (but it still has a Tado on the radiator) and it doesn't impact on my bill… And as it stands it impact my energy report because it is constantly on. Thanks in advance
-
Energy IQ to take account of hot water
I find the energy IQ quite useful but it would be so much better if it took into account the gas usage for heating hot water. Can this be implemented so that energy usage for hot water can be shown both separately and combined with heating?
-
Multiple, configurable schedules
In the post-pandemic world splitting schedules by Weekday / Weekend is not flexible enough. We work sometimes in the office, sometimes from home. The kids are sometimes in school, sometimes there is a school break. And so on. It's incredibily time consuming and tedious to have to readjust schedules every time a change…
-
Set a Minimum Central Heating Flow Temperature (OpenTherm)
Hi, The main purpose of this post is to try and gain an understanding of whether setting a minimum central heating flow temperature is a feature that other users of this forum would value and like to be developed by Tado as part of their algorithms. Are there any other users out there that have abandoned using the…
-
Change your shipping delivery service provider
Not just me, but many other customers from ROMANIA are dissapointed with the service provided by UPS. Packages from Tado and other european businesses are not delivered and the reasons invoked by UPS are FALSE: incomplete contact information, the receiver was not available for delivery. UPS doesn't contact the receiver at…
-
Added functionality to TADO SMART AC Control - Panasonic 8/10 degrees mode missing
Hello TADO, Please make an update to your current offering so that you can utilize this functionality on Panasonic air-air heat pumps. This useful feature 8/10 degrees feature is built-in to the heat pumps and is available on the standard remote control. I am convinced that a considerable number of TADO users in the Nordic…
-
Local Mode option for Tado X
Reading the manuals it would seem that if a wireless temperature sensor goes offline, the controller will continue to heat as per the schedule. However, with the server issues the last couple of days I had the following; One Wireless receiver X controls one zone and hot water and was running a schedule. The wireless…
-
Re Server failure issues
Hello I was asked to give a description of a concern I have, regarding your recent server outage and the lack of a fit for purpose local control option in the event of a server outage or loss of internet connection. I have ask my son Jon to write this, as he is a Chartered Engineer and more familiar with the technical…
-
Merged: Spring/Summer and Autumn/Winter settings
This discussion has been merged.