-
morco GB24 combi boiler
hi im looking for some help on how to wire the v3+ reciever to my morco GB24 combi boiler to control my heating thankyou
-
Radiator thermostat dead after battery change
Today I had two radiators with the message: low battery. So I decided to change them. I replaced the batteries in both radiator thermostats and only one came alive and the other is dead in the water. No lights, no nothing. Does anyone know how to reanimate the radiator thermostat? FYI: new batteries, tried to change…
-
Adding Underfloor Heating Systems
My house has a central heating system plus underfloor heating in 3 rooms. Can I bring the 3 x underfloor heating systems into my Toda environment as separate zones. So I would have 1 x room thermostat, 3 x smart radiator valves & 3 x underfloor heating controls - 7 zones in total. 2 of the underfloor heating systems are…
-
Where to put the cables?
When I took off my functioning thermostat, I noticed the wires are not connected in the way as I know them. I know that the blue cable is generally speaking always the Neutral wire. This doesn’t seem to be the case here (I checked other thermostats, and they are all wired this way). Should I put the blue wire in P1, like…
-
New boiler
I need a wiring diagram to wire an existing tado system to a new boiler that tado does not recognise
-
Tado if overshooting with new boiler
Hi, I recently swapped my old system boiler for a combi. I specifically got a boiler with opentherm so Tado could modulate it and that is all wired up and working fine. I’ve actually had my Tado for many years and have swore by it. But since swapping the boilers my rooms are always over shooting when they didn’t do that…
-
About a AC Control unit v2. Is this the normal behavior of The AC Control unit?
The AC control unit turns on and off the Heatpump unless I manually use The remote control unit. BR. pjok01, Denmark.
-
Tado V3 Wired Starter Kit with Glowworm Essential 28c Boiler - Heating just stays on
Hello, I have installed and configured the wired starter kit with my Glowworm Essential 28c boiler but no matter what I have set in the app for the heating schedule, the boiler just stays on. I have: Wired the eBus terminations correctly. Registered the internet bridge, receiver and wireless temp sensor and they appear…
-
Boost Heating used to work brilliantly but not now!
I have reprogrammed the heating. Maybe that works!
-
Suisse, western area around Vaud. Installation engineers? Anyone?
kendrick@bluewin.ch 0044 7557 806315
-
Tado Smart AC Control Constantly connecting and disconnecting from WiFi.
Hi, I have a Tado Smart AC Control that shows E04 on the display. It is constantly connecting to my WiFi network for 0s, and disconnecting, only to reconnect again and repeat the process. This is ridiculous behaviour. The reason it can't connect to the Tado servers, and why it's showing E04 is because there is no internet…
-
Combi boiler hot water control
Hello everyone. A bit of pickle here with hot water control and i can't seem to find an answer to it. I have a vaillant ecotec pro (vcw 289 i believe) hooked up to tado via ebus. Works like a charm when it comes to heating, no issues here. But i have a problem with hot water control as it seems to have overtaken the…
-
Install Tado on Vaillant ecoVIT plus VKS INT 196
Hello, is it possible to install a Tado smart thermostat (starter kit v3+) on a Vaillant ecoVIT plus VKS INT 196 ? And how? (Connections on the board, ebus...?) Cannot find any info about that. Thanks.
-
Turn open window notification off
Is there a way to keep the open window Detection on (with 30 min timer) but avoid the notifications?
-
Wiring Tado Wireless Controller to Joule Kodiak Tank and Samsung Gen 6 Heat Pump
Hi Just had a Samsung / Joule Air to Water Heat Pump Installed. At the moment its wired with the Samsung Wired Programmer setup, We purchased the Tado Wireless kit to work as the main thermostat for the central heating, and are hoping that it can also be used to give some control to the domestic hot water as well (This is…
-
Fitting smart thermostat to M30 x 1.5mm valve head
I am fitting smart thermostat to a M30 x 1.5mm valve head (probably Myson) and getting error E2. This means no contact between the pin and the thermostat. Any ideas on how to resolve this?
-
Worcester Bosch Heatslave 15/19 combi oil boiler wiring instructions please?
Hi, I have a Worcester Bosch Heatslave 15/19 combi oil boiler from around 2005 and there are no wiring instructions integrated in the app...... so i was wondering if anyone can help please or suggest a model that is equivalent/same that I can then click and follow that wiring in the app ? I have bought the Tado Wireless…
-
Black temperature sensor
Tado make a black thermostat, why not a black temperature sensor?
-
reset tado v2
Hi how i reset a tado v2? i tried to touch with two finger the arrow but nothin appened bye
-
Wiring a Honeywell ml1 5sb
Hi I have an old Honeywell thermostat Wired identically to this one . My understanding is: Earth to P1 2 to P2 3 to NO 1 to COM Can anyone confirm this is correct?
-
Viessman Vitodens and V3 thermostat boiler issue
I have a Viessman 100-W B1HF-M and a V3 Tado setup The bridge, hub and thermostat are all connected to the WiFi However when adjusting settings via the app or using the thermostat it doesn’t ‘call’ the boiler Link below is to an image of the current wiring. How do I fix this? https://ibb.co/9V93SHp
-
Vokera vibe wiring
Hi I was fitting a tado to my brothers with the above combi, and when setting the tado up it couldn’t find the boiler model, do we email support for wiring instructions ? Thanks
-
tado + MCZ
Bonjour, J'ai un poêle a pellets de Marque MCZ avec une télécommande infrarouge ou on peut gérer la température est ce que TADO fonctionnerais dessus? Merci de votre retour
-
Setpoint change through TRV always "While in home mode" despite set to "Until next automatic change"
I have several rooms in my home. For each of these rooms I have set settings => room => "Manual Control on tado device" to "Until next automatic change". For most rooms this works as expected: When I change the setpoint using the TRV, the app displays "Until <next block time> while in Home Mode" for that room. However for…
-
Boiler keeping firing
Ever since I put in smart thermostats the gravity fed boiler keeps firing for approximately 20 secs every 4-5 mins. It’s not on a separate zone so is “always on” along with the two heating zones which the smart thermostats are on. Any thoughts?
-
Vaillant Ecotec Plus 35KW - is it supported?
As titled - looking for the v3+ wireless kit.
-
Greenstar 4000 Combi Boiler
Hi All, I have a Greenstar 4000 combi boiler and I'd like to use the digital connection to enable hot water pre-heating and control the heating via modulation. Is this possible with the Tado Wireless receiver (V3+)? If not is there a converter I can get for the Greenstar to make it talk OpenTherm and then connect it to the…
-
hello
hello mally ewtrwetwte3
-
Wireless Smart Thermostat V3 - Vitodens boiler - OpenTherm query
Hi - I have an Visseman Vitdodens 100 OpenTherm compatible boiler. OpenTherm updated their technology in 2021 and I want to know it the Wireless Smart Thermostat V3 supports the full latest Open Therm technology which was updated in 2021? I presume I need to get the EU version? If so, is there anything additional required?…
-
Why can't Home Assistant see TADO thermostats?
TADO working fine if individual STRVs are added to dashboards but where 2 x STRVs are controlled in TADO by the room stat in that room I cannot get the thermostat onto the dashboard. This means the zone temperature cannot be simply adjusted like a single STRV can. Looking for a fix by TADO!