-
WiFi 6 capability/upgrade
Hi with 3 floors to my house the wireless capability to speak to a single bridge may be causing issues for me. Is there a solution that provides far. Ore effective wifi6 capability or comparability with a wifi6mesh network? TIA
-
schedules that can be assigned to week numbers (for co-parenting)
When faced with co parenting, kids are typically away for a week and the next week they're back. During the off weeks, no heating in their rooms and their bathroom is required and that cost can be saved. In vacation time this scheduling can change, for example two weeks of and then back. So having the ability to make two…
-
Open window toggle
Can we add in the option to tell a thermostat that you’ve opened a window. Many times a window might be open but it’s not detected and as the temperature drops the heating kicks in. Currently if I open a window I have to lower the thermostat so it doesn’t kick in but if I could just switch it to open window so the…
-
Keep the radiator valve open for a while after the temperature has been reached.
So the smart thermostat button works like this. You set a temperature like 20 degrees. However the room is19 degrees. Tado turns the valve of the radiator open and your central heating boiler starts heating. However after the temperature has been reached, Tado gives a stop signal but immetiately shuts down the radiator…
-
Redundancy in the event of internet loss of server faults
Currently Tado does not have an effective method of controlling their system locally if the internet goes down or if their is a fault on their servers. Can tado re assess this and provide a way to still use the heating controller locally via a smart phone connected to the same WIFI network as the Tado devices, so that in…
-
Tado Smart App - Learn function
I would embrace a Learn function in the App, where I could point my original AC remote to the Tado-device, to "Learn" functions available in the original remote, i.e. Silent Mode, Swing, Defrost mode, Timer Set etc. To use these Learnt functions I suggest to be able to have custom buttons on the Tado App Home screen.
-
Valve pin position indicator
My Bosch system which I got rid of in favor of Tado included in the app a place where you could see the position of the valve pin. This was useful to determine if TRV was fully opening or closing the valve pin and other temperature issues. I think this would be useful on the Tado system as well
-
Antifreeze & déactivation possibilty
Hello, Support told me that it s not possible to deactivate or change the antofreeze temperature. The minimum temperature when you set to off is 5°C. I would like to be abble to set the antifreeze temperature at a temperature below 5°C (as set by default). And also to be abble to deactivate completely a radiator head. This…
-
dealing better with low battery: add a new battery state "yellow"
i have noticed a couple times that i get a tado e-mail that a device needs new batteries but when i look at the app it will show a green battery icon and "good" the cause is, i think: during a cold night the batteries have lower capacity and the e-mail get sent. the app will also show a red icon when looked at right after…
-
Relative units in Energy IQ setup
In residential buildings there are still some individual radiator meters. In the Energy IQ setup one can only give kWh or m3 as unit but this is only available on a building level. Can something be done to use individual meter readings from Techem meters for example?
-
UK Customer Service Telephone Number
Currently no UK customer service telephone number is available. This is not good for Elderly people who are less technically endowed then other generations and when they have a fault just want to speak to someone to get the fault rectified especially in the Middle of a UK winter. It causes allot of anxiety. Given the…
-
Settings after signal loss and auto-reconnect
Regarding the wireless receiver of the central heating, it is undesirable for it to remain on when there is no signal. I have returned several times to a home with tropical temperatures after the signal was lossed for unknown reason (so far) and the heater remains (last setting before disconnection). Can't this be set to…