Active

A Pause Button… with Adjustable Duration
I would like to suggest a Pause button… Similar to the Boost button but with the opposite effect. Or add a time restriction to the Off button. With the weather so variable there are times when the heating just does not need to come on if one of the rooms drops 0.2 degrees below the target temperature. With temperature…
Show the water temp that goes into a radiator or warn if too low
So, I had an issue with our central heating. Two-story apartment, the lower floor was fine, the upper floor not so much. Out of three radiators upstairs, one was kinda happening, the rest cold. I noticed it was a bit chilly. I played around with the two cold ones, removed the thermostat, and eventually called the landlord…
Set temperature for selected rooms shortcut
It would be useful if I can select the rooms fast where I would like to set a temperature for the next hour other than doing it individually. Thank you,
Active / Inactive rooms fast switch
I wold like to include a fast button for each room within the main view to mark that room as 'active' or 'inactive'. That way you can switch on/off the room you are currently using with a click. This would be nice.
Time block call for heat option
In the room time blocks, provide the ability to choose at different times whether thermostat calls for heat, or operates in passive mode
Smart AC Control V3+ / Setup Quiet Mode
Dear Support, It would be a great plus for the product tado smart ac control v3+ to support quiet mode. The controller already supports fan control and adding this feature will provide the benefit of completely giving away the hard manual controller of an older air condition. Maybe a generic mode could be added for the…
Allow additional schedules in addition to Home and Away
It would be great if it was possible to have additional schedules in Tado. I’d like if you were able to add additional schedules, such as “day shift” and “night shift” or “staycation”, so you can easily change schedules to meet your requirements. For example it I found i needed to change my normal schedule to account for…
modo frio para el termostato
Actualmente tengo un sistema de suelo radiante/refrigerante y necesitaría que los termostatos tuvieran una función de frío para poder usarlo tanto en invierno como en verano. Esto ya se lleva pidiendo durante años en el foro Tanto en ingles:…
Merged: Smart Radiator summer / maintenance / bleeding mode (leaving the radiator open)
This discussion has been merged.
Holiday Schedule
Would it be possible to add in a calendar feature to pre-programme upcoming Holidays? E.g. enter a time and date for the holiday to start and for it to end? This would remove the need to remember to switch all heating and hot water to 'Off' as you leave, plus allow for pre-planning and set the holiday parameters (e.g.…
Bridge range extender
Nearly all my issues with tado revolve around lack of connection between the radiator thermostats and the bridge. Surely either a more powerful Bridge or a bridge extender could be developed
Lowering frost protection or turn it off per device
I have a conservatory attached to the property and the temperature can go down as low as 3 or 4°. A useful feature to be able disable frost protection for this area or choose a lower level for frost protection, such as zero.
Some Suggestions
Tadoº Ecosystem Ability to use AC thermostat as a sensor to give temperature readings to radiator valves or the radiator thermostats (this is a big turn down). On the App (iOS) System: Ability to add shortcuts to iOS system, allowing to activate Boost Heating, Resume Schedule, Turn Off All, more easily. Geofencing: ability…
Timed override for geofencing
Would be good to have a way to override geofencing (to home or away, from auto) for a set period of time - like the timed manual override for TRVs. I manually override geofencing to ‘Home’ so that heating stays on for babysitters when I leave the house. But then I have to remember to turn back to “Auto” when I get home.…
Visitors pre-set
It's probably been suggested before but I'd love a preset for certain rooms so you can quickly switch between occupied and unoccupied. For example we have 2 X guest bedrooms. When visitors come it would be really helpful to have a preset to quickly switch the heating schedule on just for their rooms. When unoccupied we…
show humidity on room tile
Why do I have to go into a room to see the humidity? There’s enough space on each room tile to add the humidity figure.
Display Humidity level on wired and wireless sensor display
It would be important to allow the display of humidity levels on the wired and wireless sensors (square devices) when pressing the round button. This feature could be configured in the app. The humidity level would be displayed just after the temperature. You can also extend this display to smart radiator valves.

Active

Discussion List