-
Daikin Heat Pump Compatibility
I am looking for a smart home heating solution and contacted support to assess compatibility for Tado X which states it accommodates under floor systems. Support informed me that Tado X is not compatible with Daikin Altherma R F - EHVH-CB and Daikin ERLQ006CAV3. I would suggest adding compatibility as this is a widely…
-
Maximum flow temperature per smart thermostat
Please enable setting max flow temperature per smart thermostat, not per whole central heating system. When smart thermostat controlling underfloor heating calls for heat alone (radiators don't ask for heat) there is no need to heat the system so high. A lot of users have mixed systems (ufh + radiators) so it would be…
-
Set a working temperature range
In the intelligent programming section there isn't the feature to set a minimum and a maximum temperarture. Currently, you can only set a maximum temperature above which the heating switches off and below which it switches on. It would be nice if you could set a minimum temperature below which the heating is activated and…
-
Summer mode
My son has a Netatmo system and during the summer, the connected valves calibrate every 2 weeks, even when the thermostat is off, so that the thermostatic heads do not get calcified or stuck (which may happen if the valve is fully closed for a couple months). With Tado, I need to take all my programming to put the valves…
-
Add support for Worcester 8000 digital control
One of the biggest boiler brands in the UK, and yet there is no digital support from tado. I want my boiler temperature properly controlled and modulated, not just on and off. Tado markets itself as being compatible with a really wide range of boilers and controllers, so to miss this (for years) is appalling. I just…
-
More intelligent Balance
I have been using Balance functionality for a while now. The idea is great, however I find the "rules" for decreasing the temperature by 2° during high energy price periods too static. A few ideas to make this more "intelligent": If a "Balance period" coming up during which my "home" otherwise would be heated up a lot,…
-
Increase or decrease temperature by 2° everywhere (instead of Boost Beating)
Sometimes you just want it to be slightly warmer or slightly cooler in your entire home. Therefore a "Decrease by 2°" button would be useful to reduce the temperature in all rooms. And another one "Increase by 2°". Ideally coupled with a setting for how long this should apply. A bit like the current 30-minute ‘Boost…
-
Real window sensors from tado
We would like a real window / door sensor for the "window open function". The current detection of the open windows via the thermostats works so far quite well. However, we have discovered some problems. 1. In some rooms the detection of an open window does not work or does it too late (e.g. bathroom, room with balcony or…
-
Make a window sensor that turn the heating off (the open window detection doesn't work so well)
Make a little window sensor as an option that could be installed at a window and connected with one or more Tado thermostats, so that one or more thermostats totally close the heat, when the window is open. The present open window detection closes if it feels colder air, but it works very badly because it often turns heat…
-
Battery status Matter
Hello, when Tado X radiator thermostats are connected to HomeAssistant using Matter Addon they dont show battery status because its not sending any. The radiator thermostats are connected through other brand Thread Border router.
-
Allow swiping to access next room
Once you selected a room you should be able to just swipe to the next room but have to come out of the room to go back to the home screen and then select the next room; this is rather cumbersome and was much easier in the pre-v3+ app
-
Decrease burner power before lowering target flow temperature
Hi, I have a bosch condens 2500 boiler, connected with nefit opentherm-ems converter. Using this setup with tado x wireless receiver (+trvs, wireless thermostats), via opentherm control. As far as I see, this setup works well, changing the target flow temeprature and setting the burner power to minimum value happens, so…
-
Boiler Overun
When all heating demand is stopped our boiler goes into overrun and dissipates it heat into the garage (where it is not required). It would be good if when the heating is not called for boiler heat demand signal is stopped but the radiator valves would stay open for a adjustable time to use the stored boiler heat in…
-
thermostat mode
Hello, the choice to eliminate the possibility of setting the operating mode on the thermostat (legacy mode) to turn off the air conditioner "manually" is wrong; it was a very useful option.
-
my.tado.com : support for 2FA
Hi. There is a ETA for support 2FA for the accesso to my.tado.com ? Best regards
-
Profiles (again)
How much work will there be to enable us to create differnt profiles in the app? I know its been asked before but users seem to have an answer by adjusting the existing home profiles. I DONT WANT TO DO THIS. I want to press a button when for example we have guests staying or if we have a snow day or i'm working from home…
-
Funzioni in app
1 ) Sarebbe utile integrare in app la possibilità di variare manualmente la temperatura di mandata dell'acqua. 2) Quando alla caldaia è collegata una sonda esterna utilizzare la temperatura letta da essa ( sicuramente più precisa ) per regolare la temperatura interna perchè i dati del meteo sono troppo generici e succede,…
-
Better support for Underfloor Heating
Hi, I would like to request better software support for underfloor heating systems in the Wired Thermostats when using relay mode. The modulation used by the Tado Wired Thermostates is not beneficial to my system because it tries to turn the UFH on and off repeatably when NOT calling for "full heat" (i.e. when calling for…