-
Tado X - notifications on SRVs
Hi, I've just moved from a V3 system to new X system. I'm still learning how the new system is working and I've just set a very simple configuration with just one room. I'm currently using 6 SRVs. First point I'd like to investigare is about switch on/off or temperature modification performed through the App or the…
-
Disable TRV "calibration" when offset is changed [required for using external sensor]
As you may have read elsewhere on this forum, myself and other Tado users have been working on ways to make Tado TRVs more usable by using cheaper external sensor to read the actual room temperature and dinamically update the temperature offset of the valves with great results. The only drawback of that is that we have to…
-
Setting for binary relay operation
I have used my Tado V3+ thermostat to replace an old fashioned binary thermostat. Love the features but find the 3 'wiggly lines' levels of heating very frustrating (and slow to heat rooms). Would it be possible to add a setting which provides a simple binary on/off heating arrangement i.e. the relay is always on if the…
-
Internet Bridge local API
It’d be great if it were possible to interact with the Internet Bridge using a local API so that requests don’t need to be made via the internet. Presumably there’s some kind of http server on the device as HomeKit is able to communicate with it locally?
-
Tado x regolare la temperatura dei caloriferi, impostare icona quando la caldaia è accesa
Buonasera chiedo di poter impostare su ogni testa termostatica la temperatura di mandata nel calorifero per tutti quelli che non hanno il protocollo opentherm in modo tale da regolare automaticamente con l'algoritmo in base al meteo ecc la temperatura dell'acqua dei termosifoni. Mettere una spia su app per vedere quando si…
-
Support newer version of Worcester HT-BUS
I just upgraded from a worcester bosch greenstar cdi to a worcester bosch greenstar 8000 life. On my old boiler I could connect to the digital low voltage interface bus however the new boiler the ht-bus is not supported and I couldn't simply change over I had to rewire to the old relay style. The bus interface is better…
-
Dedicated tile for boiler status on/off (same as hot water)
Im fairly new to Tado but one feature i've seen that is so blindly obvious i though i was doing something wrong. It would be great to have a tile on the app which shows if the wireless recevier is actively calling for heat. Similar to the "hot water on/off" tile. A boiler on/off tile. I know there are the ~~~ wavey lines…
-
Schedule a boost
I am often away from home. My underfloor heating has a 24 hour thermal lag from 6 degrees to 22 degrees. I regularly forget to preheat it. Can you please add a facility to diarise a temperature boost for one or more rooms?
-
Hybrid Heat Pump support [Atlantic Aurea 5 R32]
This heatpump comes with the plugwise Anna thermostat using the opentherm protocol to control most combi-boilers, so they control the heatpump and the combi-boiler, but one must remove the Tado thermostat. If plugwise can control the hybrid system, it should be trivial for tado to do the same thing. I would like to remove…
-
Geolocation Improvement's for Mobile users W3W?
Tado like devices often get repurposed into not conventional ‘homes’, such as canal boats and Rv’s Could the home location be made dynamic either using data from the home network ( our teletonica router has a gps function)? If that is too complicated or not possible due to the hardware limitations in the internet bridge,…
-
Support more than 10 rooms and 25 devices
Please can you add support for more than 25 devices and only 10 rooms, with a 5 bedroom house, with ensuites with a number of downstairs rooms, 25 devices is not enough when you want radiator TRVs and smart thermostats in each room. also limiting the total rooms to 10 does not work in this environment either. Please,…
-
IFTTT replacement - customised boost temperature and duration
I used to use IFTTT to boost my heating to 21 or 22 degrees for 1-2 hours depending on the setting. It was WAY more useful than just 25 degrees for 30 minutes. Tado removed the integration, but could features like this be integrated into the app then? It seems like an easy change, we can already boost, it just needs to…
-
Night mode
Hi, I think it would be useful to have a "night mode" with a setting in temperature. With the other modes, away and home can be set as a scene recognised by alexa, Google home. So we can stop heating the apartment or some rooms when we go to sleep with third-part routines/automations.
-
Worcester Bosch Greenstar 8000 and EMS
Please can you configure the Tado wired unit to work with the Worcester Bosch Greenstar 8000 and EMS
-
Stabilizing heat demand pattern for constant set temperature
I live in Scandinavia and often work from home, so I have a consistent heating demand throughout the day. When looking at the temperature/heating graph view, it is clear that the heating demand (and temperature) follows a cyclic pattern with a period of 45min on average. I'd love to post an image but I don't think this…