-
If at least 1 connected device is available in a room, to read and control from that
1) in a rooms settings and you select the measuring device. If that is connected then don’t grey out the room, put a red spot to indicate one of the devices has an issue. Allowing you to control the room still as and when the others connect they sync 2) energyIQ data source and units. Can we add litres for oil consumption ?
-
Disable away mode notifications when heating is off
The away mode notifications work well for me, however they don’t make any sense when the heating is off. So the weather is warm, I’ve turned the heating off, but I still get an away mode notification every time I leave the house. Any reason these couldn’t be disabled automatically while the heating is off?
-
Battery Power for AC control rather than mains plug and 1.8m lead
I have AC in bedrooms and the your smart AC control would be an attractive convenient addition to my smart heating intallation. It would be much neater to have these powered by batteries as opposed to a mains plug with 1.8m lead trailing up a wall which is very unsightly and severely limits placement options Look forward…
-
EnergyIQ bad UI design for viewing history
Hi, Thanks for the latest EnergyIQ update: >> Energy IQ has been updated, and now you can view your historical heating consumption all the way back to when you first installed tado°. To check your consumption from a previous period, open the Energy IQ skill and select the desired month from the dropdown menu at the top of…
-
Vane angle positioning on tado Smart AC
Hello! With the latest firmware (100.0) of tado Smart AC Control it is still not possible to control an angle of vanes on an AC unit :( This feature would be quite welcome and I hope for tado's support in this regard. Thanks and regards, Zarko.
-
Select and copy serial number to clipboard
When contacting technical support they request the serial number of the device. You have to manually type it in when you should be able to long press and copy to clipboard
-
Energy IQ Tariff rounding bug
The gas price is 5.65p (UK pence) per kWh and previously it was 3.44p per kWh. However Tado App asks to enter this as £ so I enter 0.0565 and 0.0344. However Tado rounds this to 0.06 and 0.03 which is quite a large rounding error, resulting in a bad estimation. Could you please update this to allow more digits. Thank you &…
-
Ventilation remote solution needed
Hi, could you please help me to find the right device to add to my existing tado° set (Wireless temp sensor+wireless receiver+internet bridge) which work perfectly to heat the house, but not to cool it down. I would need to control the existing manual ON/OFF ventilation switch as well, based on the inside temperature in…
-
Temperature monitor or probe for Hot water tank
Please can we add a remote temperature probe for a Hot water tank. Simular to a radiator thermostat. However it will tell the temperature of the Hot water Tank. This could also be used to integrate temperature control for the Hot water and weather to re-heat, turn on the hot water or turn off.
-
Store a basic schedule locally in case of crash / lost connection
My Tado system crashed when I went on holiday when the boiler was on. It stayed on max heating until I got home. Quick sums showed it had burned abut £50 in gas (which Tado refunded in the end) but surely it makes sense to store a limited schedule locally, at the boiler controller. What's potentially worse is if the system…
-
Silence mode activation for Vaillant (GREE) airco
I have a Vaillant airco, which is acutely a GREE airco. I’m really happy with the Tado remote, but i can’t select silence mode. It is the mode I use the most. Please add this function to the Tado remote
-
Energy IQ area & Data Analysis improvements
Hi, After the last time suggestions about the review the previous data and Yes, I can see the delveoper quick changed now. The previous data with the m3 usage only rather there had the cost £ figure in the current montly. (current month, that could choice m3 leave or cost £$)..Hope that can be apply to the previous data as…