-
Baxi System 100he boiler
I'm thinking of buying Tado V3+ Wireless Heating & Hot Water Smart Thermostat Starter Kit and Smart radiator valves. Does anyone know if they are compatible?
-
Replacing Myson MPRT with Wired Tado – Second Wireless Zone Compatibility and Setup Questions
Hi everyone, I’m planning to upgrade my thermostat setup and recently purchased the Tado Wired Smart Thermostat Starter Kit V3+ to replace my wired Myson MPRT (in the living room). The wired Myson is currently not working and controls the heating for the living room, kitchen, hallway, and bathroom. In addition, my bedrooms…
-
How to supply power to the EU opentherm receiver in UK?
As title states, how could one supply power/wired the EU opentherm wireless receiver in the UK for modulation? I understand it comes with EU plug already attached according to the description. I have three basic ideas, though one may not be all that smart/safe, idk 😂 1. Just use an EU to UK plug adaptor. 2. Actually have…
-
Need help with tado°
I'd like to describe my newest experience with Tado support. I have some problems with hot domestic water - it gets heated to too high temperature. What feedback I got from Tado representative: "That may be the reason the OT connection is not fully compatible. An installation tado° Smart Thermostat directly to your boiler…
-
New/Old system problem
I've just bought a complete system from a neighbour who gave up on it. I got it for a song, but I am having an issue with it. I bought it and set it up a while back, can't remember exactly when (maybe 8 weeks), but I did so because I'm going away for a couple of weeks and wanted to set a couple of rooms to stay at a set…
-
Room no longer getting up to temperature
Before Christmas I installed a wireless Tado thermostat to control the whole house. It worked fine but I wanted to be able to control the bedrooms separately so I don't heat them during the daytime. To do this I bought four smart TRVs to fit on the upstairs bedroom radiators. Since fitting these I've found the system not…
-
Hot Water Turned On Outside of Schedule
Hi Everyone I have just completed my Tado Wireless V3+ Installation with the bridge, wireless thermostat, wireless receiver and 5 TRVs. I followed the installation settings exactly. I have a Y-Plan system with a heat only boiler and a Hot Water cylinder. The HW cylinder has with a Cylinder Thermostat which is set to 65c.…
-
Heating randomly stays on and exclamation mark present!
My Tado V3+ system and TRVs have been fitted for 3 months with no problems. However, on a couple of occasions the central heating will remain on past the thermostat set temperature. The heating then remains on no matter what I do, unless I hard reset the Tado sender unit in the airing cupboard. I also notice that the…
-
V1 Installtion
Hi I have the original V1 beta which I have not used since probably 2019. I powered it up today and it said all components were offline. I then deleted the home so that I can add everything back again. But it's asking for the serial number and 4-11 digit code. I have the serial number but where do I find the code?
-
Altantic Boiller and Tado wiring
Hi everyone, I'm in the process of replacing my old thermostat with a wired Tado V3, but I'm running into an issue. The old thermostat had just two wires connected to it, and following the manual instructions, I connected these to the + and - terminals on the Tado (on the right-hand side) and set the correct settings…
-
Thermostat Receiver not communicating with boiler
Hi there, we had a danfoss receiver installed previously and we replaced it with Tado. We followed the same wiring based on how the danfoss was wired and for a couple of days it was working fine. After 2-3 days the Tado stopped communicating with the boiler and now when we boost the heating on the app or turn on the…
-
Maximum flow temperature per smart thermostat
Please enable setting max flow temperature per smart thermostat, not per whole central heating system. When smart thermostat controlling underfloor heating calls for heat alone (radiators don't ask for heat) there is no need to heat the system so high. A lot of users have mixed systems (ufh + radiators) so it would be…
-
Collegamente IMMERGAS VICTRIX TERA V2 28kw con Tado
Volevo capire se è possibile collegare la mia caldaia IMMERGAS VICTRIX TERA V2 28kw a sistema Tado V3+ mendiante uscite digitali OT Opentherm e quindi in modulazione.
-
Energy IQ update...
Hi, so Energy IQ was pretty good when I started with Tado (4 years or so?). It then went lottery mode where it would just show nonsense. Has anyone else noticed them fixing it? The December numbers are within 80 kWh! That is pretty impressive…
-
Tado won't talk to boiler. I'm cold and losing the will to live...
It's like a loveless marriage, they've fallen out after four years and will no longer speak to each other, just sitting there will folded arms refusing to budge. Go easy… I'm not an electrician or a plumber but have had both of these people (both trusted people who I know) out to try and fix this issue without success.…
-
Google Home integration only allows queries, no set commands
Hi, i have a home setup where Tado is correctly added to the Google Home setup, same room names etc. I use the Google Assistant embedded in a Sonos One speaker. I can perfectly ask questions like 'Ok google, what is the temperature in the kitchen" with replies like Tado is set to 17 degrees and the current temp is 18,5…