-
Battery status Matter
Hello, when Tado X radiator thermostats are connected to HomeAssistant using Matter Addon they dont show battery status because its not sending any. The radiator thermostats are connected through other brand Thread Border router.
-
Allow swiping to access next room
Once you selected a room you should be able to just swipe to the next room but have to come out of the room to go back to the home screen and then select the next room; this is rather cumbersome and was much easier in the pre-v3+ app
-
Multi Home Support
I would like to use tado in my main house and in my vacation home. Currently this is only possible by using one account through the app and the other account using the web-app. I would like to have both available in the same account.
-
Pre-heat and early start for Tado X
Hello, Just bought the tado x System and I am a bit disappointed that the pre-heat and early start feature are missing. Are there any plans to implement those two features? Please implement those two features🙏 Thanks, Florian
-
Decrease burner power before lowering target flow temperature
Hi, I have a bosch condens 2500 boiler, connected with nefit opentherm-ems converter. Using this setup with tado x wireless receiver (+trvs, wireless thermostats), via opentherm control. As far as I see, this setup works well, changing the target flow temeprature and setting the burner power to minimum value happens, so…
-
Boiler Overun
When all heating demand is stopped our boiler goes into overrun and dissipates it heat into the garage (where it is not required). It would be good if when the heating is not called for boiler heat demand signal is stopped but the radiator valves would stay open for a adjustable time to use the stored boiler heat in…
-
Give users access to the advanced configuration parameters
As most of us here will be aware, Tado has several advanced controls and configuration options that support are able to use to configure your devices when you contact them (cycle periods, minimum on/off times etc). Sadly these advanced options are hidden from users and the only way to access them is through support which…
-
thermostat mode
Hello, the choice to eliminate the possibility of setting the operating mode on the thermostat (legacy mode) to turn off the air conditioner "manually" is wrong; it was a very useful option.
-
my.tado.com : support for 2FA
Hi. There is a ETA for support 2FA for the accesso to my.tado.com ? Best regards
-
Profiles (again)
How much work will there be to enable us to create differnt profiles in the app? I know its been asked before but users seem to have an answer by adjusting the existing home profiles. I DONT WANT TO DO THIS. I want to press a button when for example we have guests staying or if we have a snow day or i'm working from home…
-
Funzioni in app
1 ) Sarebbe utile integrare in app la possibilità di variare manualmente la temperatura di mandata dell'acqua. 2) Quando alla caldaia è collegata una sonda esterna utilizzare la temperatura letta da essa ( sicuramente più precisa ) per regolare la temperatura interna perchè i dati del meteo sono troppo generici e succede,…
-
Real window sensors from tado
We would like a real window / door sensor for the "window open function". The current detection of the open windows via the thermostats works so far quite well. However, we have discovered some problems. 1. In some rooms the detection of an open window does not work or does it too late (e.g. bathroom, room with balcony or…
-
Better support for Underfloor Heating
Hi, I would like to request better software support for underfloor heating systems in the Wired Thermostats when using relay mode. The modulation used by the Tado Wired Thermostates is not beneficial to my system because it tries to turn the UFH on and off repeatably when NOT calling for "full heat" (i.e. when calling for…
-
Ability to rename device
When batteries are running low I get an email informing me that a particular device in a specific room has an issue. In some rooms I have 4 radiators. I then have to go round ‘blinking’ the stat multiple and watching all the stats in the room to find which one it is. it would be great to be able to rename or give a…
-
Enable eBUS support for Tado X Wireless receiver
The V3+ supports both eBUS and Opentherm however the newer product series X does not support eBUS. Please enable also eBUS support for the X series. I imagine since you have the code for V3+ in the firmware it could be refactored over for the X and with a firmware update it could work.
-
Reduce the comfort temperature range to 18-21°c
In the uk a room set for the comfort range of over 20°c can far exceed a comfortable temperature. I would suggest reducing this so my app doesn't think my house is cold all the time
-
[Energy IQ] Allow for new meter and continue entering meter readings
When replacing a meter, it becomes hard to continue entering meter readings as one has to add the last old meter reading to the new meter readings (and sometimes even subtract the first new meter reading from that number too). Under Energy IQ, provide a meter reset button, with for the date of changeover: ++ the first new…