-
Ability to rename device
When batteries are running low I get an email informing me that a particular device in a specific room has an issue. In some rooms I have 4 radiators. I then have to go round ‘blinking’ the stat multiple and watching all the stats in the room to find which one it is. it would be great to be able to rename or give a…
-
Ebus Max Flow Temperature setting (like the one just released for Opentherm).
Would it be possible to do the same for Ebus controlled boilers via the wired Tado, +- settings? My Vaillant can ramp up to 80C if it wants even if I set the max temp lower on the boiler. The ebus will ignore these settings and do what it feels is best. I might only want it to go to 66 or 70C max for example. It's just…
-
Offline notification
My Internet Bridge went off-line and I didn't realise for hours. A simple reset was all it took to fix the issue, which I could have done way sooner if I'd realised. Tado sends other notifications, like a thermostat needing batteries. I would like Tado to send me a notification, either push-notification in the app, or…
-
Worcester Bosch 4000 ems control
Please enable support of EMS / Ebus functionality so Tado can control modulation of this boiler
-
Pre-heat and early start for Tado X
Hello, Just bought the tado x System and I am a bit disappointed that the pre-heat and early start feature are missing. Are there any plans to implement those two features? Please implement those two features🙏 Thanks, Florian
-
Provide method to specify type of heating system, i.e. radiators, underfloor, etc.
There is no facility to specify what type of heating system is installed. It appears Tado treats all systems as if the heating system is based on radiators. In case of a underfloor only system it is likely the floor is cold when the first call for heat after a break is generated. Currently the system would start to run for…
-
3rd party temperature sensor support or cheaper add-on temperature sensor
I have multiple tado radiator thermostats, but all of them are a couple of degrees out with the actual temperature. I use an Aqara temperature sensor to measure the actual temperature in the room, further away from my radiator. It would be great if the tado app could use the data of these aqara sensors to measure the…
-
Dedicated tile for boiler status on/off (same as hot water)
Im fairly new to Tado but one feature i've seen that is so blindly obvious i though i was doing something wrong. It would be great to have a tile on the app which shows if the wireless recevier is actively calling for heat. Similar to the "hot water on/off" tile. A boiler on/off tile. I know there are the ~~~ wavey lines…
-
allow changing the name of devices
Please allow us to change the names of devices to make it easier to identify them. For example, getting an email that tells me: "We have noticed that the batteries in your Smart Radiator Thermostat VA*******048 in the zone ****** are running low." I have 15 devices and if each device had a name I wouldn't have to waste…
-
Notificación al móvil en caso de encendido/apagado de calefacción
Una sencilla forma de saber si se ha puesto en marcha la calefacción en nuestra casa (o en una estancia de ella) a través de una notificación al móvil (tira o globo) especialmente si nos encontramos fuera de nuestro hogar. Igualmente se podría notificar apagado de calefacción. Estas notificaciones podrían activarse o…
-
Setup modulation for underfloor heating
Hello, I have underfloor heating in my family house and have set a constant temperature of 22.5°C on the Tado V3 thermostat. Last night, the outdoor temperature was 2°C. At 1:15 am, the indoor temperature dropped to 22.5°C, and Tado started heating at the lowest level (one bar). It continued to heat at one bar from 1:15 am…
-
Create a range extender or let us use a second bridge...
Having olny 1 bridge per house is a massive design flaw yet to be addressed by Tado. Unless you leave in a tiny house made of cardboard walls, the TRV wlll lose connection or burn batteries in only a matter I'd a couple of weeks. I live in a house across 3 floors, I really struggle with the range and can't have full…
-
Set Humidex instead temperature
It can be useful to have the option to set the perceived temperature instead only the normal temperature. In the high humidity zones temperature is not significant. It would be nice to trigger the air conditioning with your wireless control to decrease humidity.
-
Smart wall plug for underfloor heating pump
You offer nearly everything except a way to turn a underfloor heating pump on or off. My living room thermostat is connected to the underfloor heating, and to control the pump I have to set up a complicated process through Homey and a Z-Wave smart wall plug. It would be great to have a Tado smart wall plug which can be…
-
Give users access to the advanced configuration parameters
As most of us here will be aware, Tado has several advanced controls and configuration options that support are able to use to configure your devices when you contact them (cycle periods, minimum on/off times etc). Sadly these advanced options are hidden from users and the only way to access them is through support which…