-
Smart Radiator summer / maintenance / bleeding mode (leaving the radiator open)
When summer comes, the valves should stay in open position. With the currently available modes, specially referring to "OFF", the valves stay closed. This is dangerous for the valves themselves, risk to get stucked, and for the pumps of the boilers which run periodically to prevent pump lock due to long inactivity.
-
Group rooms
Can you add a feature to group rooms (i.e. ground floor / first floor etc) to a cluster to be able to boost / switch off with one click.
-
Holiday Schedule
Would it be possible to add in a calendar feature to pre-programme upcoming Holidays? E.g. enter a time and date for the holiday to start and for it to end? This would remove the need to remember to switch all heating and hot water to 'Off' as you leave, plus allow for pre-planning and set the holiday parameters (e.g.…
-
Bridge range extender
Nearly all my issues with tado revolve around lack of connection between the radiator thermostats and the bridge. Surely either a more powerful Bridge or a bridge extender could be developed
-
Change the hysteresis / PID settings
Hi Tado. The current desire of the smart thermometer algorithm to track the set temperature is killing my hardware. It is turning it on/off so often that things are breaking (like TCVs). How about I can select the min and max settings that trigger a state change? Or if it is a PID system, I should be able to change the…
-
Lowering frost protection or turn it off per device
I have a conservatory attached to the property and the temperature can go down as low as 3 or 4°. A useful feature to be able disable frost protection for this area or choose a lower level for frost protection, such as zero.
-
Some Suggestions
Tadoº Ecosystem Ability to use AC thermostat as a sensor to give temperature readings to radiator valves or the radiator thermostats (this is a big turn down). On the App (iOS) System: Ability to add shortcuts to iOS system, allowing to activate Boost Heating, Resume Schedule, Turn Off All, more easily. Geofencing: ability…
-
Timed override for geofencing
Would be good to have a way to override geofencing (to home or away, from auto) for a set period of time - like the timed manual override for TRVs. I manually override geofencing to ‘Home’ so that heating stays on for babysitters when I leave the house. But then I have to remember to turn back to “Auto” when I get home.…
-
Maximum Temperature Limit
Hi there, with the increasing cost of fuel , I was thinking that a maximum temperature limit may be of some use that could be set by the account holder in order to prevent "temperature tampering" by anyone not authorised. This could possibly be built into the app, and hopefully could save money. Any thoughts !
-
Visitors pre-set
It's probably been suggested before but I'd love a preset for certain rooms so you can quickly switch between occupied and unoccupied. For example we have 2 X guest bedrooms. When visitors come it would be really helpful to have a preset to quickly switch the heating schedule on just for their rooms. When unoccupied we…
-
show humidity on room tile
Why do I have to go into a room to see the humidity? There’s enough space on each room tile to add the humidity figure.
-
Display Humidity level on wired and wireless sensor display
It would be important to allow the display of humidity levels on the wired and wireless sensors (square devices) when pressing the round button. This feature could be configured in the app. The humidity level would be displayed just after the temperature. You can also extend this display to smart radiator valves.
-
Support newer version of Worcester HT-BUS
I just upgraded from a worcester bosch greenstar cdi to a worcester bosch greenstar 8000 life. On my old boiler I could connect to the digital low voltage interface bus however the new boiler the ht-bus is not supported and I couldn't simply change over I had to rewire to the old relay style. The bus interface is better…
-
Plieger
Goedemiddag, Wil toch even reageren op onderstaande mail van jullie. Misschien dat jullie er iets mee kunnen?! Ik heb een Herz adapter M30 inwendig naar M28 uitwendig gekocht waar een messing sukje bij zat wat over de pen van de kraan past. Ik heb enkel het messing stukje op de en gezet en….. tadaaa, de Tado knop werkt.…